低频聚苯胺/硅橡胶复合材料屏蔽效能的分析

分析了以掺杂态聚苯胺为填料、硅橡胶为基体的复合材料的导电性以及其在3-1500MHz频段下的屏蔽效能。研究结果表明,随着聚苯胺加入量的增加,体电阻率明显下降,屏蔽效能稳定提高。当加入重量比为100：100时,屏蔽效能在16-19．3dB,体电阻率与原橡胶相比下降12个数量级。     

铜钴镍铁氧体/聚苯胺复合物的制备及其电磁性能

采用水热法制备铜钴镍铁氧体粉末,通过原位聚合法制备具有改善电磁屏蔽性能的铜钴镍铁氧体/聚苯胺复合材料.通过X射线衍射(XRD)、扫描电子显微镜(SEM)和热失重分析仪(TG)来表征该复合材料的形态和结构.研究结果表明,聚苯胺均匀包覆铜钴镍铁氧体,与原始的铜钴镍铁氧体和聚苯胺相比,铜钴镍铁氧体/聚苯胺复合材料显示出增强的屏蔽效果.当铜钴镍铁氧体含量为40％、涂层厚度为2.5 mm时,铜钴镍铁氧体/聚苯胺复合材料的最佳屏蔽效果达到-50 dB,这表明铜钴镍铁氧体/聚苯胺复合材料具有良好的电磁性能.     

石墨烯/聚苯胺复合材料的电磁屏蔽性能

采用直流电弧放电法制备高结晶性石墨烯, 利用乙醇助溶分散法得到石墨烯/聚苯胺电磁屏蔽复合材料, 研究不同掺杂比例的石墨烯/聚苯胺复合材料的电磁屏蔽性能。拉曼光谱分析表明: 由于石墨烯与聚苯胺之间的相互作用, 复合材料中聚苯胺特征峰比纯聚苯胺特征峰稍弱或向低频方向移动。复合物的电导率随石墨烯掺杂量的增加而增大, 当掺杂质量分数为25%时, 其电导率达到19.4 S/cm, 接近纯石墨烯电导率(20.1 S/cm)。频率为2~18 GHz时, 复合材料的电磁屏蔽效能随着石墨烯掺杂量和频率的增大而增强; 当石墨烯掺杂质量分数为25%时, 总屏蔽效能在2~18 GHz范围内由19.8 dB增至34.2 dB, 增加了约42%, 其中吸收部分占总屏蔽效能的比例为66%~81%, 这表明石墨烯/聚苯胺复合材料的电磁屏蔽性质是以电磁波吸收为主; 同时也说明了拥有特殊结构与特性的石墨烯是一种较好的聚苯胺填料, 在微波屏蔽与微波吸收领域将会有广阔的应用前景。     

石墨烯/纳米银复合材料的制备、微结构及其导电性能

将不同比例的氧化石墨烯(GO)和硝酸银混合,采用水合肼一步还原制备石墨烯/纳米银(RGO/Ag)复合材料。采用UV-vis、XRD、FTIR和SEM对RGO/Ag复合材料结构组成进行表征分析,并结合热流量和结构变化研究其构成和热处理工艺对导电性的影响。结果表明:Ag基本以类似球形与石墨烯(RGO)复合;RGO/Ag复合材料的导电性与其构成有很大关系,只有当GO加入量小于50wt%时,Ag含量的提高和热处理工艺的优化可以明显改善复合材料的导电性,其中,GO加入量为16wt%的RGO/Ag片方阻值可达到8mΩ/□;当GO加入量高于50wt%时,复合材料导电性与RGO接近,受Ag含量的提高和热处理工艺优化的影响较小。     

低温聚苯胺/碳纳米管复合材料的制备

采用原位聚合法合成出了具有较高导电性的聚苯胺及聚苯胺 /碳纳米管复合材料 ,考察了不同碳纳米管添加量对聚苯胺 /碳纳米管复合材料表面形态、材料结构及导电性的影响并进行了表征。结果证实 ,制备出的复合聚苯胺的电导率比所见报道值提高了 1～ 2个数量级 ,为高电导率聚苯胺的合成开辟了更广阔的前景。     

PANI/SnO2导电复合材料的制备及光催化吸附性能

采用水热合成法制备了类球状二氧化锡纳米粉体,再经原位聚合工艺制备聚苯胺(PANI)/SnO2纳米复合材料。利用红外光谱(IR)、X射线衍射(XRD)、扫描电镜(SEM)和透射电镜(TEM)表征了材料的结构和形貌,用四探针测试了材料的电导率,考察了反应物配比对复合材料导电性及光催化吸附性能的影响。结果表明,PANI与SnO2之间存在着化学键的结合,形成交联的孔状结构。复合材料兼具良好的导电性和较高的光催化吸附性能,掺杂30%SnO2纳米粒子时,复合材料的电导率为3.57 S/cm,相比于掺杂态聚苯胺提高了将近十倍,对萘酚绿B的吸附降解率达98%,且循环使用率较高(80%±6%)。     

PANI-HCl/PAN电磁屏蔽纳米纤维膜的制备与表征

用化学方法合成盐酸掺杂的导电聚苯胺,然后以静电纺丝技术制备PANI-HCl/PAN纳米柔性电磁屏蔽材料。利用红外光谱和扫描电镜分别对纳米纤维结构和形貌进行表征分析,并用电子万能试验机和矢量网络分析仪分别对导电聚苯胺薄膜的力学性能及屏蔽特性进行了测试和分析。结果表明,随着PANI-HCl含量的增加,纺丝溶液的电导率增加,纳米纤维直径减少,力学性能降低;PANI-HCl/PAN纳米薄膜的电磁屏蔽性能随着薄膜厚度的增加,电磁屏蔽性能提高,当薄膜厚度为91.04μm时,薄膜的电磁屏蔽效能达到20.38dB;同时,纳米纤维膜在低频段均表现良好的电磁屏蔽效果,在1～9MHz频率范围内,当聚苯胺的含量达到13%时,屏蔽率达到90%以上。     

聚苯胺导电材料的制备及表征

采用溶液聚合法和乳液聚合法制备了聚苯胺(PAn)导电材料.考察了所得PAn的产率、溶解性和电导率,并用红外光谱和X射线衍射对产物的结构进行了表征.结果表明乳液聚合法制备的掺杂态PAn有着更高的产率、更好的溶解性、导电性和更好的结晶性.     

超级电容器用聚苯胺/有序介孔炭复合电极的性能

利用原位聚合法制备了聚苯胺/有序介孔炭复合材料.通过恒流充放电、循环伏安和交流阻抗测试考察了不同聚苯胺含量对聚苯胺/有序介孔炭复合材料电化学性能的影响.研究表明:与纯的有序介孔炭和聚苯胺相比,聚苯胺/有序介孔炭复合材料具有更高的比容量,良好的稳定性和充放电循环性能.当聚苯胺质量分数为60%,电流密度为0.1A·g-1时,比容量可以达到409F·g-1.     

掺杂纳米SnO_2-Al_2O_3/Cu新型电触头复合材料的制备及耐磨性能

为满足低压电器对于高品质电触头材料的迫切需求,同时保护稀缺资源、降低电触头成本,采用粉末冶金工艺制备了掺杂纳米SnO_2-Al_2O_3/Cu新型电触头复合材料,并对其电导率、硬度及耐磨性能进行了研究。结果表明:复烧与冷变形工艺均可显著提高复合材料的烧结质量、密度、电导率与硬度。随着纳米Al_2O_3及掺杂纳米SnO_2颗粒的总含量增加,掺杂纳米SnO_2-Al_2O_3/Cu电触头复合材料的硬度与耐磨性能表现出了相同的变化规律,即先升高后降低。当纳米Al_2O_3及掺杂纳米SnO_2颗粒的总含量为0.80wt%时,复合材料的硬度与耐磨性能均达到最优;而当纳米Al_2O_3及掺杂纳米SnO_2颗粒的总含量保持0.80wt%不变时,随纳米Al_2O_3颗粒的含量增加,掺杂纳米SnO_2-Al_2O_3/Cu电触头复合材料的硬度与耐磨性能改善;当掺杂纳米SnO_2颗粒的含量为0时,复合材料的耐磨性能达到了最优。因此较之掺杂纳米SnO_2颗粒,纳米Al_2O_3颗粒对掺杂纳米SnO_2-Al_2O_3/Cu电触头复合材料的耐磨性能有更显著的提高作用。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.