Effect of Sulfur Precursor on Dimensions of One-dimensional CdS Nanocrystals

One-dimensional CdS nanocrystals have been prepared by solvothermal method using cadmium acetate as a cadmium precursor,elemental sulfur and Na2S,as a sulfur precursor,and ethylenediamine as a solvent at 150℃ for 5 h.The nanocrystals were characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM),transmission electron microscopy(TEM) and UV-Vis absorption spectroscopy.XRD patterns indicate that both Na2S and elemental sulfur as the sulfur precursor result in CdS nanorods with wurtzite phase(h...     

Synthesis of organic ligand passivated zinc selenide nanorods via wet chemical route

Zinc selenide (ZnSe) nanorods have been synthesized by simple and inexpensive wet chemical method using N-Methylaniline as a capping agent. The morphologies and structure of ZnSe nanorods have been characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The SEM and TEM reveal the formation of nanorods. XRD shows the cubic structure with the lattice constant of 5.633 Å. Strong “blue shift” absorption is observed from UV-visible spectrophotometry. The enhanced luminescence property is measured from photoluminescence spectrophotometry. The presence of N-Methylaniline in the ZnSe nanorods is confirmed by the Fourier transformed infrared spectrum.     

多孔NiO纳米棒:可牺牲模板法制备及其磁性(英文)

本文基于微乳液法制备了长度几微米、直径20-100纳米的NiC2O4纳米棒,以此为可牺牲模板得到多孔NiO纳米棒,并采用FESEM、TEM、HRTEM、XRD、FTIR对产物的形貌和结构进行了表征。研究表明,所制多孔NiO纳米棒是由NiO颗粒组成,且NiO颗粒的直径可随热处理温度变化。同时研究了NiO纳米棒的磁性性能,制备的NiO纳米棒显示出随NiO颗粒尺寸变化的铁磁性特征。     

CO2-mediated synthesis of ZnO nanorods and their application in sensing ethanol vapor

High-purity ZnO nanorods have been synthesized via a two-step route using zinc acetate as a precursor without any surfactant and additive. In this method, ZnCO3 fibers were first formed in the CO2-ethanol solution, which directed the formation of ZnO nanorods by subsequent treatment in KOH aqueous solution. The as-prepared nanorods were fully characterized by transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy and Fourier transform Infrared spectroscopy. It was found that the as-obtained ZnO nanorods were single crystals with uniform diameter around 150 nm and length of 4 microm. The nanorod crystals were prismatic with hexagonal cross sections, consistent with the wurtzite lattice structure. Moreover, the sensing properties of the as-prepared ZnO nanorods were also investigated. It was demonstrated that they exhibited good performance for detecting ethanol vapor even at 380 and 250 degrees C.     

Rapid growth of nanotubes and nanorods of würtzite ZnO through microwave-irradiation of a metalorganic complex of zinc and a surfactant in solution

Large quantities of single-crystalline ZnO nanorods and nanotubes have been prepared by the microwave irradiation of a metalorganic complex of zinc, in the presence of a surfactant. The method is simple, fast, and inexpensive (as it uses a domestic microwave oven), and yields pure nanostructures of the hexagonal würtzite phase of ZnO in min, and requires no conventional templating. The ZnO nanotubes formed have a hollow core with inner diameter varying from 140–160 nm and a wall of thickness, 40–50 nm. The length of nanorods and nanotubes varies in the narrow range of 500–600 nm. These nanostructures have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and selected area electron diffraction (SAED). The ZnO nanorods and nanotubes are found by SAED to be single-crystalline. The growth process of ZnO nanorods and nanotubes has been investigated by varying the surfactant concentration and microwave irradiation time. Based on the various results obtained, a tentative and plausible mechanism for the formation of ZnO nanostructures is proposed.     

Chemical bath deposition of ZnO nanorods for dye sensitized solar cell applications

ZnO nanorods using various molar concentrations have been synthesized through the chemical bath deposition method. X-ray diffraction result shows that the ZnO nanorods are of hexagonal structure. The morphology of the ZnO nanorods has been examined by scanning electron microscopy. The ZnO nanorods have diameters ranging from 100 to 200 nm and length of 1–3 μm. Dye-sensitized solar cells have been assembled by using ZnO nanorod film photoelectrode sensitized using natural dye extracted from lantana camara as sensitizer. The ZnO nanorods have been used as electrode material to fabricate dye sensitized solar cells which exhibited an efficiency of 0.71 %, the maximum efficiency was obtained for films deposited for 0.07 M concentration.     

Fabrication and characterisation of MnOOH and β-MnO2 nanorods with rectangular cross-sections

MnOOH nanorods with rectangular cross-sections have been successfully prepared in high yield via a hydrothermal reduction process at a low temperature. After the subsequent heat treatment of the as-prepared MnOOH nanorods at 350°C for 6?h in air, β-MnO₂ nanorods with rectangular cross-section that retained the similar morphologies of MnOOH nanorods were obtained. The products were characterised by powder X-ray diffraction and field-emission scanning electron microscopy. The influences of different degrees of pH on the morphology and phase of the final products under hydrothermal conditions are discussed.     

Microemulsion-based synthesis of porous zinc ferrite nanorods and its application in a room-temperature ethanol sensor

Porous zinc ferrite (ZnFe(2)O(4)) nanorods with a diameter of around 50?nm and a length of several micrometers have been synthesized by a microemulsion-based method in combination with calcination at 500?°C. The morphology and structure of the ZnFe(2)O(4) nanorods and its precursor (ZnFe(2)(C(2)O(4))(3) nanorods) were systematically characterized by x-ray powder diffraction, transmission electron microscopy, field emission scanning electron microscopy and high-resolution transmission electron microscopy. The formation mechanism for the porous ZnFe(2)O(4) nanorods is also discussed. Moreover, the porous ZnFe(2)O(4) nanorods were applied in a room-temperature ethanol sensor and exhibited much better sensing performance than ZnFe(2)O(4) nanoparticles.     

The effects of addition of citric acid on the morphologies of ZnO nanorods

ZnO nanorods of 25-100 nm in diameter and 0.2-1 μm in length were fabricated through citric acid assisted annealing process. The microstructure of ZnO nanorods was characterized by X-ray diffraction, transmission electron microscopy, high-resolution transmission electron microscopy and field-emission scanning electron microscopy, respectively. As a result, it was found that ZnO nanorods were single crystalline and pure. The effects of the growth conditions such as addition of citric acid, annealing temperature on the morphologies of ZnO nanostructures have also been investigated. At the given temperature the length decreased but the diameter increased with addition of the mass of citric acid. With the rising of the calcining heat, the shape of ZnO changed from rod to granule for a given amount of citric acid. Finally, the mechanism for citric acid assisted annealing synthesis of the ZnO nanostructure is discussed.     

V205纳米棒的软化学法合成

采用一种简单的软化学法制备出直径大约为50nm的V2O5纳米棒。此方法无需添加表面活性剂或催化剂，只使用原料和水。合成的产物经XRD、SEM、TEM、FT-IR等分析手段进行表征。另外基于实验结果，进一步提出了可能的形成机理。     

Synthesis and gas sensor properties of flower-like 3D ZnO microstructures

Flower-like ZnO 3D microstructures composed of nanorods have been successfully prepared via a facile hydrothermal method using p-nitrobenzoic acid as the structure-directing agent. The structures and morphologies of the final products have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high-resolution transmission electron microscope (HRTEM). The possible mechanism for the synthesis of the flower-like ZnO microstructures has been proposed primarily. The gas sensitivity of the flower-like ZnO microstructures has been studied to a series of organic vapors at different operation temperatures and vapor concentrations. The results show that the flower-like ZnO microstructures composed of nanorods have good gas sensor properties to ethanol.     

Effect of Tm doping on the properties of electrodeposited ZnO nanorods

ZnO nanorods were fabricated by electrodeposition from solution with and without thulium precursors and characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, photoluminescence and time-resolved photoluminescence. In spite of the low incorporation of thulium into ZnO nanorods, both the morphology and the optical properties of the nanorods were affected by the presence of thulium. The light emitting diodes with ZnO nanorods with and without Tm have been demonstrated.     

Synthesis of zinc oxide nanotetrapods and nanorods by thermal evaporation without catalysis

ZnO nanotetrapods and nanorods have been synthesized by a simple thermal evaporation of Zn powder (300 mesh, 99.99% purity) under simultaneous flow of oxygen and argon gases in two-zone furnace in two different temperature regions. These ZnO nanostructures have hexagonal structure, which grow along the [001] direction in the form of nanotetrapods (diameter approximately 60-150 nm, length approximately 1-4 microm) and nanorods (diameter approximately 30-60 nm, length approximately 2-5 microm). The morphologies of these ZnO nanostructures have been investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It has been found that growth parameters like temperature, gas flow rate etc., control the diameter of the nanotetrapods and nanorods. These novel structures of ZnO nanorods and nanotetrapods may be attractive for optical and other nanodevices.     

Rutile structured SnO2 nanowires synthesized with metal catalyst by thermal evaporation method

One-dimensional (1-D) nanostructures such as tubes, rods, wires, and belts have attracted considerable research activities owing to their strong application potential as components for nanosize electronic or optoelectronic devices utilizing superior optical and electrical properties. Characterizing the mechanical properties of nanostructure is of great importance for their applications in electronics, optoelectronics, sensors, actuators. Wide-bandgap SnO2 semiconducting material (Eg = 3.6 eV at room temperature) is one of the attractive candidates for optoelectronic devices operating at room temperature, gas sensors, and transparent conducting electrodes. The synthesis and gas sensing properties of semiconducting SnO2 nanomaterials have became one of important research issues since the first synthesis of SnO2 nanobelts. Considering the important application of SnO2 in sensors, these structures are not only ideal systems for fundamental understanding at the nanoscale level, but they also have potential applications as nanoscale sensors, resonator, and transducers. The structured SnO2 nanorods have been grown on silicon substrates with Au catalytic layer by thermal evporation process over 800 degrees C. The resulting sample is characterized and analyzed by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), and energy-dispersive X-ray spectroscopy (EDS). The morphology and structural properties of SnO2 nanowires were measured by scanning electron microscopy and high-resolution transmission electron microscopy. The mean diameter of the SnO2 nanorods grown on Au coated silicon (100) substrate is approximately 80 nm. In addition, X-ray diffraction measurements show that SnO2 nanorods have a rutile structure. The formation of SnO2 nanowires has been attributed to the vapor-liquid-solid (VLS) growth mechanisms depending on the processing conditions. We investigated the growth behavior of the SnO2 nanowires by variation of the growth conditions such as gas partial pressure and temperature.     

A simple microwave-assisted decomposing route for synthesis of ZnO nanorods in the presence of PEG400

In the paper, a simple microwave-assisted decomposing reaction in the presence of PEG400 has been successfully developed to synthesize ZnO nanorods with 10-25 nm of diameter and 60-200 nm of length. The product was analyzed and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and HRTEM. Ultraviolet-visible (UV-vis) absorption peak of ZnO nanorods shows a distinct blue shift from that of the bulk and the Photoluminescence (PL) spectrum exhibits a strong near-band-edge emission at 385 nm. Further experiments have also been designed, and the results show that microwave radiation and surfactant PEG400 all played an important role on the formation of ZnO nanorods.     

Growth of well-aligned ZnO nanorods using auge catalyst by vapor phase transportation

Well-aligned ZnO nanorods have been achieved using new alloy (AuGe) catalyst. Zn powder was used as a source material and it was transported in a horizontal tube furnace onto an AuGe deposited Si substrates. The structural and optical properties of ZnO nanorods were characterized by scanning electron microscopy, high resolution X-ray diffraction, and photoluminescence. ZnO nanorods grown at 650 degrees C on 53 nm thick AuGe layer show uniform shape with the length of 8 +/- 0.5 microm and the diameter of 150 +/- 5 nm. Also, the tilting angle of ZnO nanorods (+/- 5.5 degrees) is confirmed by HRXRD. High structural quality of the nanorods is conformed by the photoluminescence measurement. All samples show strong UV emission without considerable deep level emission. However, weak deep level emission appears at high (700 degrees C) temperature due to the increase of oxygen desertion.     

Functionalization of atomic force microscope tips by dielectrophoretic assembly of Gd(2)O(3):Eu(3+) nanorods

An atomic force microscopy (AFM) tip has been coated with photoluminescent Eu(3+)-doped Gd(2)O(3) nanorods using a dielectrophoresis technique, which preserves the red emission of the nanorods (quantum yield 0.47). The performance of the modified tips has been tested by using them for regular topography imaging in tapping and contact modes. Both a regular AFM standard grid and a patterned surface (of an organic-inorganic methacrylate Zr-based oxo-cluster and poly(oxyethylene)/siloxane hybrid) have been used. Similar depth values have been measured using a conventional silicon tip and the nanorod-modified tip. The tips before and after use exhibit similar SEM images and photoluminescence spectra and, thus, seem to be stable under working conditions. These tips should find applications in scanning near-field optical microscopy and other scanning techniques.     

From cobalt nitrate carbonate hydroxide hydrate nanowires to porous Co(3)O(4) nanorods for high performance lithium-ion battery electrodes

We have developed a simple approach for the large-scale synthesis of cobalt nitrate carbonate hydroxide hydrate (Co(CO(3))(0.35)(NO(3))(0.2)(OH)(1.1)·1.74H(2)O) nanowires via the hydrothermal process using sodium hydroxide and formaldehyde as mineralizers at 120?°C. The porous Co(3)O(4) nanorods 10-30?nm in diameter and hundreds of nanometres in length have been fabricated from the above-mentioned multicomponent nanowires by calcination at 400?°C. The morphology and structure of cobalt nitrate carbonate hydroxide hydrate nanowires and Co(3)O(4) nanorods have been characterized by transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM) and x-ray powder diffraction (XRD). Moreover, the porous Co(3)O(4) nanorods have been applied in the negative electrode materials for lithium ion batteries, which exhibit high electrochemical performance.     

Growth of TiO2 Nanorods by Sol-gel Template Process

In this work, TiO2 nanorods with uniform diameter of about 100 nm and a length of several micrometers were successfully prepared by the sol-gel template method. Also the influence of molar ratios of precursor on the morphology and structure of TiO2 nanorods has been investigated. The prepared samples were characterized by Fourier transform infrared spectroscopy （FTIR）, X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The XRD results indicated that the TiO2 nanorods were crystallized in the anatase and rutile phases, after annealing to 400-700℃ up to 2 h.     

Gas sensing properties of ZnO nanorods prepared by hydrothermal method

ZnO nanorods are prepared by a hydrothermal process with cetyltrimethylammonium bromide (CTAB) and zinc powder at 182°C. The samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The gas sensing properties of the materials have been investigated. The results indicate that the as-prepared ZnO nanorods are uniform with diameters of 40–80 nm and lengths about 1 μm, the relatively high sensitivity and stability of these sensors made from ZnO nanorods demonstrate the potential for developing a new class of stable and very sensitive sensors.