Strengthening in and fracture behaviour of CNT and carbon-fibre-reinforced epoxy–matrix hybrid composite

Advanced materials such as continuous fibre-reinforced polymer matrix composites offer significant enhancements in strength and fracture resistance properties as compared with their bulk, monolithic counterparts. In the present work, mode-I (tensile) fracture behaviour of the neat epoxy (without nano- or hybrid reinforcements), nanocomposite (with amino-functionalized multi-walled carbon nanotube (MWCNT) reinforcement to neat epoxy) and hybrid composite (with amino MWCNT and carbon fibre reinforcements to neat epoxy) along with their flexural strength and interlaminar shear strength has been reported and discussed. Limited topological studies have also been conducted to understand the nature of material fracture and its dependence on the notch orientation. The results thus obtained are analysed and discussed in detail to elucidate: (i) alignment of fibre and its influence on the anisotropy in strength and fracture resistance, (ii) dependence of notch root radii on the apparent fracture toughness and concurrence to strain-controlled fracture and (iii) finally, the nature of J–R curves. The results thus obtained have revealed that the resistance to fracture is significantly increased with the addition of amino-functionalized MWCNTs and carbon fibres. In the hybrid composite, fracture resistance is greater in the longitudinal orientation of fibres than in the transverse orientation and it exhibits a significantly higher strength–fracture toughness combination.     

Reinforcement effects of MWCNT and VGCF in bulk composites and interlayer of CFRP laminates

The reinforcement effects of two nanofillers, i.e., multi-walled carbon nanotube (MWCNT) and vapor grown carbon fiber (VGCF), which are used at the interface of conventional CFRP laminates, and in epoxy bulk composites, have been investigated. When using the two nanofillers at the interface between two conventional CFRP sublaminates, the Mode-I interlaminar tensile strength and fracture toughness of CFRP laminates are improved significantly. The performance of VGCF is better than that of MWCNT in this case. For epoxy bulk composites, the two nanofillers play a similar role of good reinforcement in Young’s modulus and tensile strength. However, the Mode-I fracture toughness of epoxy/MWCNT is much better than that of epoxy/VGCF.     

The influence of silicate-based nano-filler on the fracture toughness of epoxy resin

Dispersion of nano-sized, silicate-based filler in epoxy resin is expected to yield improved materials properties in several areas. Various mechanical properties, specifically improved fracture toughness, as well as improved flame-retardant effects are of interest. The final objective of the research is investigating whether a nano-modified epoxy matrix yields improved delamination resistance in a fiber-reinforced laminate compared to a laminate with neat epoxy as matrix material. As a first step towards this goal, the fracture toughness of nano-modified epoxy resin is compared with that of the neat resin. Fracture toughness improvement up to about 50% and energy release rates increased by about 20% are observed for addition of 10 wt.% of organosilicate clay.     

Fracture mechanisms of epoxy filled with ozone functionalized multi-wall carbon nanotubes

This work focused on the fracture mechanisms and reinforcing effects of ozone-treated multi-walled carbon nanotubes (MWCNTs) in epoxy matrix. Ozone functionalization of MWCNTs was found to be of help for a better dispersion and stronger interfacial bonding with epoxy matrix, which in turn improve the strength and fracture toughness of the resin. The MWCNT/epoxy composites showed complicated failure modes than the conventional fibrous composites, which have been quantitatively investigated and correlated with the fracture toughness of the nanocomposites studied.     

Mechanical,thermal and microstructural characteristics of cellulose fibre reinforced epoxy/organoclay nanocomposites

Epoxy nanocomposites reinforced with recycled cellulose fibres (RCFs) and organoclay platelets (30B) have been fabricated and investigated in terms of WAXS, TEM, mechanical properties and TGA. Results indicated that mechanical properties generally increased as a result of the addition of nanoclay into the epoxy matrix. The presence of RCF significantly enhanced flexural strength, fracture toughness, impact strength and impact toughness of the composites. However, the inclusion of 1 wt.% clay into RCF/epoxy composites considerably increased the impact strength and toughness. The presence of either nanoclay or RCF accelerated the thermal degradation of neat epoxy, but at high temperature, thermal stability was enhanced with increased char residue over neat resin. The failure micromechanisms and energy dissipative processes in these nanocomposites were discussed in terms of microstructural observations.     

Reinforcement of ball shaped MoS2 nanoparticles in epoxy resin

The present work involves the synthesis of molybdenum disulfide (MoS2) nanoparticles by annealing the precursor obtained from simple reflux method. XRD, FESEM and HRTEM confirmed the formation of 2H-MoS2 with ball shaped particles, where some of them possess coalesced dumbbell morphology. The reinforcement of polysulphide modified epoxy resin (PSER) by MoS2 with varying amounts from 0.150 to 0.200 wt% provides unique combination of the improved thermal stability, tribological and mechanical properties. XRD studies indicate interaction between the sulphur containing nanoparticles and the epoxy resin. Maximum improvements in tensile strength (440%) and toughness (534%) are observed with ball shaped MoS2 nanoparticles (0.150 wt%)/PSER composite. Also the coefficient of friction and wear resistance show improvements of 60 and 78% respectively for 0.175 wt% loading in PSER compared to the neat resin matrix. Thermal stability is found to be improved maximum by 23 degrees C, when 5% weight loss is taken as a point of comparison. Similar studies on synthetic microcrystalline MoS2 filled PSER show that improvements in all these properties are very inferior.     

多壁碳纳米管/聚醚砜环氧树脂复合材料的制备及力学性能

环氧树脂具有优异的热性能及力学性能,但本身脆性较大。为制备低成本、高性能的环氧树脂体系,使用聚醚砜（PES）和多壁碳纳米管（MWCNT）对环氧树脂进行增韧,制备了不同PES含量的PES-环氧树脂共混物,讨论了PES含量对环氧树脂力学性能的影响;采用熔融法,并配合使用机械搅拌、高剪切分散和超声分散制备了MWCNT/PES-环氧树脂复合材料,测试了其拉伸性能及断裂韧性,用SEM观察了MWCNT在树脂中的分散状态以及拉伸试样的断口形貌。结果表明：MWCNT的加入能够提高PES-环氧树脂体系的综合力学性能,且当MWCNT含量为0.7wt%时,树脂体系的综合力学性能最好;低PES含量下,小于1.0wt%的MWCNT的加入使材料力学性能超过用20.0wt%PES改性的环氧树脂;PES与MWCNT对环氧树脂具有协同增韧作用。     

Improved fracture toughness of carbon fibre/epoxy composite laminates using dissolvable thermoplastic fibres

This paper reports on a novel toughening concept based on dissolvable phenoxy fibres, which are added at the interlaminar region in a carbon fibre/epoxy composite. The composites were prepared by resin infusion of carbon fibre fabric with the phenoxy introduced as a chopped fibre interleaf between the carbon fibre plies. The thermoplastic phenoxy fibre dissolved in the epoxy during curing at elevated temperatures and a phase separated morphology with phenoxy-rich secondary phase was formed upon curing. It was found that the average Mode-I fracture toughness value, G_1c increased tenfold with only 10 wt.% (with regard to the total matrix content) phenoxy fibre added. Other properties such as Young’s modulus, tensile strength and thermal stability were not adversely affected. The mechanical and thermal properties of the neat epoxy–phenoxy blends were also studied for comparison.     

Enhancement of mechanical performance of epoxy/carbon fiber laminate composites using single-walled carbon nanotubes

Carbon nanotubes (CNT) in their various forms have great potential for use in the development of multifunctional multiscale laminated composites due to their unique geometry and properties. Recent advancements in the development of CNT hierarchical composites have mostly focused on multi-walled carbon nanotubes (MWCNT). In this work, single-walled carbon nanotubes (SWCNT) were used to develop nano-modified carbon fiber/epoxy laminates. A functionalization technique based on reduced SWCNT was employed to improve dispersion and epoxy resin-nanotube interaction. A commercial prepregging unit was then used to impregnate unidirectional carbon fiber tape with a modified epoxy system containing 0.1 wt% functionalized SWCNT. Impact and compression-after-impact (CAI) tests, Mode I interlaminar fracture toughness and Mode II interlaminar fracture toughness tests were performed on laminates with and without SWCNT. It was found that incorporation of 0.1 wt% of SWCNT resulted in a 5% reduction of the area of impact damage, a 3.5% increase in CAI strength, a 13% increase in Mode I fracture toughness, and 28% increase in Mode II interlaminar fracture toughness. A comparison between the results of this work and literature results on MWCNT-modified laminated composites suggests that SWCNT, at similar loadings, are more effective in enhancing the mechanical performance of traditional laminated composites.     

Bisphenol A based polyester binder as an effective interlaminar toughener

Bisphenol A based thermoplastic polyesters are commonly used in the industry as binders, or tackifiers, to produce cost-saving preforms in Liquid Composite Moulding processes such as Vacuum Assisted Resin Transfer Moulding (VARTM). However, it is often reported that the presence of these polyesters has a detrimental effect on the mechanical properties of the resulting composite laminates. In contrast, this study shows that interlaminar toughness can be increased without negatively affecting other properties by coating the reinforcing plies with a bisphenol A based thermoplastic polyester if some precautions are taken in mind.The polyester was added to an epoxy resin in order to study its effect on the thermophysical properties and fracture toughness of the bulk epoxy. The polyester molecules acted as a plasticizer for the epoxy resin when the polyester was added in low amounts. This increased the bulk fracture toughness of the epoxy resin by 30%. Polyester modified glass/epoxy laminates were produced and tested for Mode I interlaminar fracture toughness and flexural properties. The increased toughness of the epoxy matrix led to a 60% increased Mode I interlaminar fracture toughness of the laminates, without negatively affecting flexural stiffness and strength of the laminates.     

Dynamic fracture of carbon nanotube/epoxy composites under high strain-rate loading

We investigate dynamic fracture of three types of multiwalled carbon nanotube (MWCNT)/epoxy composites and neat epoxy under high strain-rate loading (${10}^5''–''{10}^6$ s⁻¹). The composites include randomly dispersed, 1 wt%, functionalized and pristine CNT/epoxy composites, as well as laminated, ∼50 wt% CNT buckypaper/epoxy composites. The pristine and functionalized CNT composites demonstrate spall strength and fracture toughness slightly higher and lower than that of neat epoxy, respectively, and the spall strength of laminated CNT buckypaper/epoxy composites is considerably lower; both types of CNTs reduce the extent of damage. Pullout, sliding and immediate fracture modes are observed; the fracture mechanisms depend on the CNT–epoxy interface strength and fiber strength, and other microstructures such as the interface between CNT laminates. Compared to the functionalized CNT composites, weaker CNT–epoxy interface strength and higher fiber strength lead to a higher probability of sliding fracture and higher tensile strength in the pristine CNT composites at high strain rates. On the contrary, sliding fracture is more pronounced in the functionalized CNT composites under quasistatic loading, a manifestation of a loading-rate effect on fracture modes. Despite their helpful sliding fracture mode and large CNT content, the weak laminate–laminate interfaces play a detrimental role in fracture of the laminated CNT buckypaper/epoxy composites. Regardless of materials, increasing strain rates leads to pronounced rise in tensile strength and fracture toughness.     

Fracture toughness of the nano-particle reinforced epoxy composite

Although thermoset polymers have been widely used for engineering components, adhesives and matrix for fiber-reinforced composites due to their good mechanical properties compared to those of thermoplastic polymers, they are usually brittle and vulnerable to crack. Therefore, ductile materials such as micro-sized rubber or nylon particles are added to thermoset polymers are used to increase their fracture toughness, which might decrease their strength if micro-sized particles act like defects.In this work, in order to improve the fracture toughness of epoxy adhesive, nano-particle additives such as carbon black and nanoclay were mixed with epoxy resin. The fracture toughness was measured using the single edge notched bend specimen at the room (25 °C) and cryogenic temperature (−150 °C). From the experimental results, it was found that reinforcement with nano-particles improved the fracture toughness at the room temperature, but decreased the fracture toughness at the cryogenic temperature in spite of their toughening effect.     

聚醚醚酮增韧改性环氧树脂

采用共混法用聚醚醚酮(PEEK)改性环氧树脂(EP),借助差示扫描量热分析(DSC)确定了环氧树脂的固化工艺,测试了共混体系的工艺性能,研究了聚醚醚酮含量对环氧树脂力学性能的影响.借助扫描电子显微镜(SEM)对材料断裂面的形态结构进行了分析,探讨了体系的形态结构与冲击性能之间的关系.结果表明,在改性材料的韧性有所提高的同时,压缩强度、马丁耐热都没有降低.从断裂面的形态来看,是属于韧性断裂.当PEEK的加入量为6%时,韧性最好,达到19.1 kJ/m2,比纯的环氧树脂增加了107.6%.     

聚醚醚酮增韧改性环氧树脂

采用共混法用聚醚醚酮(PEEK)改性环氧树脂(EP),借助差示扫描量热分析(DSC)确定了环氧树脂的固化工艺,测试了共混体系的工艺性能,研究了聚醚醚酮含量对环氧树脂力学性能的影响。借助扫描电子显微镜(SEM)对材料断裂面的形态结构进行了分析,探讨了体系的形态结构与冲击性能之间的关系。结果表明,在改性材料的韧性有所提高的同时,压缩强度、马丁耐热都没有降低。从断裂面的形态来看,是属于韧性断裂。当PEEK的加入量为6%时,韧性最好,达到19．1kJ/m~2,比纯的环氧树脂增加了107．6%。     

Non-stoichiometric curing effect on fracture toughness of nanosilica particulate-reinforced epoxy composites

Non-stoichiometric curing effects on the fracture toughness behaviors of nanosilica particulate-reinforced epoxy composites were experimentally investigated in this study by comparing them with bending strengths to take into consideration the effect of interaction between nanoparticles and network structures in matrix resins. The matrixes were prepared by curing them with an excess mixture of diglycidyl ether of bisphenol A-type epoxy resin as the curing agent for the stoichiometric condition. The volume fractions of the silica particles with a median diameter of 240 nm were constantly 0.2 for all composites. The neat epoxy resins and the composites were cured non-stoichiometrically to change the crosslinking densities of the neat epoxy resins and the matrix resins of the composites within 2740–490 mol/m³. The fracture toughnesses and bending strengths of the composites and the neat epoxy resins strongly depended on the crosslinking densities in the resins. Although the fracture toughness decreased monotonously from that of the stoichiometrically cured resins as the crosslinking density decreased, the fracture toughnesses of composites were largest at a slightly lower crosslinking density of approximately 2490 mol/m³ from the stoichiometric condition of 2740 mol/m³. The fracture toughness and the bending strength were improved for crosslinking densities higher than 2000 mol/m³ by adding particles. At crosslinking density lower than 2000 mol/m³, the particles worked against the mechanical properties as defects in matrix resins.     

纳米TiO_2对复合固化环氧树脂胶粘剂的改性研究

通过添加具有活性的纳米TiO_2对异佛尔酮二胺(IPD)与酰胺基胺树脂作为复合固化剂的环氧胶粘剂体系进行改性,实验结果表明:随着纳米TiO_2的适量加入,环氧胶粘剂体系的物理性能得到很大改善,当纳米TiO_2的加入量达到6%(Wt)时,达到最佳值,与纯树脂体系相比,弯曲强度提高96%,弯曲模量提高38%,冲击强度提高180%.而此时的环氧复合胶粘剂体系的粘接性能也比纯树脂均有所提高,剪切强度提高39%、剥离强度提高28%,以及玻璃化温度提高6%.可见,纳米TiO_2的加入对环氧胶粘剂体系具有明显的增强作用.     

Effects of stretching on mechanical properties of aligned multi-walled carbon nanotube/epoxy composites

Composites based on epoxy resin and differently aligned multi-walled carbon nanotube (MWCNT) sheets have been developed using hot-melt prepreg processing. Aligned MWCNT sheets were produced from MWCNT arrays using the drawing and winding technique. Wavy MWCNTs in the sheets have limited reinforcement efficiency in the composites. Therefore, mechanical stretching of the MWCNT sheets and their prepregs was conducted for this study. Mechanical stretching of the MWCNT sheets and hot stretching of the MWCNT/epoxy prepregs markedly improved the mechanical properties of the composites. The improved mechanical properties of stretched composites derived from the increased MWCNT volume fraction and the reduced MWCNT waviness caused by stretching. With a 3% stretch ratio, the MWCNT/epoxy composites achieved their best mechanical properties in this study. Although hot stretching of the prepregs increased the tensile strength and modulus of the composites considerably, its efficiency was lower than that of stretching the MWCNT sheets.     

Cryogenic mechanical behaviors of carbon nanotube reinforced composites based on modified epoxy by poly(ethersulfone)

Cryogenic mechanical properties are important parameters for epoxy resins used in cryogenic engineering areas. In this study, multi-walled carbon nanotubes (MWCNTs) were employed to reinforce diglycidyl ether of bisphenol F (DGBEF)/diethyl toluene diamine (DETD) epoxy system modified by poly(ethersulfone) (PES) for enhancing the cryogenic mechanical properties. The epoxy system was properly modified by PES in our previous work and the optimized formulation of the epoxy system was reinforced by MWCNTs in the present work. The results show that the tensile strength and Young’s modulus at 77 K were enhanced by 57.9% and 10.1%, respectively. The reported decrease in the previous work of the Young’s modulus of the modified epoxy system due to the introduction of flexible PES is offset by the increase of the modulus due to the introduction of MWCNTs. Meanwhile, the fracture toughness (K_IC) at 77 K was improved by about 13.5% compared to that of the PES modified epoxy matrix when the 0.5 wt.% MWCNT content was introduced. These interesting results imply that the simultaneous usage of PES and MWCNTs in a brittle epoxy resin is a promising approach for efficiently modifying and reinforcing epoxy resins for cryogenic engineering applications.     

Fracture toughness and electrical conductivity of epoxy composites filled with carbon nanotubes and spherical particles

The attainment of both high toughness and superior electrical conductivity of epoxy composites is a crucial requirement in some engineering applications. Herein, we developed a strategy to improve these performances of epoxy by combining the multi-wall carbon nanotubes (MWCNTs) and spherical particles. Two different types of spherical particles i.e. soft submicron-rubber and rigid nano-silica particles were chosen to modify the epoxy/MWCNT composites. Compared with the binary composites with single-phase particles, the ternary composites with MWCNTs and spherical particles offer a good balance in glass transition temperature, electrical conductivity, stiffness and strength, as well as fracture toughness, exhibiting capacities in tailoring the electrical and mechanical properties of epoxy composites. Based on the fracture surface analysis, the complicated interactions between multiscale particles and the relative toughening mechanisms were evaluated to explain the enhancement in fracture toughness of the ternary composites.     

Modeling and mechanical performance of carbon nanotube/epoxy resin composites

The effect of multi-walled carbon nanotube (MWCNT) addition on mechanical properties of epoxy resin was investigated to obtain the tensile strength, compressive strength and Young’s modulus from load versus displacement graphs. The result shows that the tensile strength, compressive strength and Young’s modulus of epoxy resin were increased with the addition of MWCNT fillers. The significant improvements in tensile strength, compressive strength and Young’s modulus were obtained due to the excellent dispersion of MWCNT fillers in the epoxy resin. The dispersion of MWCNT fillers in epoxy resin was observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis.Also, Halpin–Tsai model was modified by considering the average diameter of internal/external of multi-walled nanotube and orientation factor (α) to calculate the Young’s modulus of multi-walled carbon nanotubes (MWCNTs)/epoxy resin composite. There was a good correlation between the experimentally obtained Young’s modulus and modified Halpin–Tsai model.