Relationships between Zr substitution for Ti and microwave dielectric properties in Mg(ZrxTi1−x)O3 ceramics

The influence of Zr substitution for Ti on the microwave dielectric properties and microstructures of the Mg(Zr_xTi_1−x)O₃(MZ_xT) (0.01 ≤ x ≤ 0.3) ceramics was investigated. The quality factors of Mg(Zr_xTi_1−x)O₃ ceramics with x = 0.01-0.05 were improved because the solid solution of a small amount of Zr⁴⁺ substitution in the B-site could increase density and grain size. An excess of Zr⁴⁺ resulted in the formation of a great deal of secondary phase that declined the microwave dielectric properties of MZ_xT ceramics. The temperature coefficient of resonant frequency (τ_f) of Mg(Zr_xTi_1−x)O₃ ceramics slightly increased with increasing Zr content, and the variation in τ_f was attributed to the formation of secondary phases.     

Structure, dielectric and electric properties of (Ba0.68−xSr0.308Bi0.006Na0.006Mgx)(Ti0.99Sn0.01)O3 ceramics

(Ba_0.68−xSr_0.308Bi_0.006Na_0.006Mg_x)(Ti_0.99Sn_0.01)O₃ ceramics were synthesized by solid-state reaction process. The samples (X ≤ 0.010) are a mixture of cubic (major) and rhombohedral (minor) phases. The rhombohedral phase causes a large dielectric loss in low temperature regions and plays an important role in diffuse phase transition of ceramics. While X > 0.010, the rhombohedral phase decreases and gradually disappears. The dielectric loss of ceramics in the low temperature regions decreases, and the samples change from the diffuse phase transition to the phase transition of second order, and then to of first order. In the temperature range of 270-370 °C, intrinsic conduction dominates conductivity of ceramics.     

Structure and electrical properties of MnO2-doped Sr2−xCaxNaNb5O15 lead-free piezoelectric ceramics

Lead-free piezoelectric ceramics Sr_2−xCa_xNaNb₅O₁₅ + y wt% MnO₂have been prepared by the conventional solid state reaction method. Our results reveal that Ca²⁺and Mn ions have entered into the Sr₂NaNb₅O₁₅ lattices to form a solid solution with tungsten-bronze structure. The substitution of Ca²⁺ induces a decrease in piezoelectric coefficient d₃₃, electromechanical coupling factors k_p and k_t, while, the addition of Mn ions decreases the sintering temperature and effectively promotes the densification of the ceramics. The effect of substitution of Ca²⁺and Mn ions on the structure, electrical properties and diffused phase changing were investigated systematically. For the ceramic with x = 0.05 and y = 0.5, the piezoelectric, dielectric and ferroelectric properties become optimum, giving a piezoelectric coefficient d₃₃ = 190 pC/N, electromechanical coupling factors k_p = 13.4% and k_t = 36.5%, ?_r = 2123, loss tangent tan δ = 0.038, remanent polarization P_r = 4.76 μC/cm², coercive field E_c = 12.68 kV/cm, and Curie temperature T_c = 260 °C.     

Structure and dielectric characterization of xNd(Mg1/2Ti1/2)O3-(1 − x)Ca0.6La0.8/3TiO3 in the microwave frequency range

The crystal structures, phase compositions and the microwave dielectric properties of the xLa(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.8Sr_0.2TiO₃ composites prepared by the conventional solid state route have been investigated. The formation of solid solution is confirmed by the XRD patterns. Doping with B₂O₃ (0.5 wt.%) can effectively promote the densification and the dielectric properties of xNd(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.6La_0.8/3TiO₃ ceramics. It is found that xNd(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.6La_0.8/3TiO₃ ceramics can be sintered at 1375 °C, due to the liquid phase effect of B₂O₃ addition observed by Scanning Electronic Microscopy. At 1375 °C, 0.4Nd(Mg_1/2Ti_1/2)O₃-0.6Ca_0.6La_0.8/3TiO₃ ceramics with 1 wt.% B₂O₃ addition possesses a dielectric constant (?_r) of 49, a Q × f value of 13,000 (at 8 GHz) and a temperature coefficients of resonant frequency (τ_f) of 1 ppm/°C. As the content of Nd(Mg_1/2Ti_1/2)O₃ increases, the highest Q × f value of 20,000 GHz for x = 0.9 is achieved at the sintering temperature 1400 °C.     

Charge compensation, electrical and dielectric behavior of lanthanum doped CaCu3Ti4O12

Mechanism of charge compensation on lanthanum, (La³⁺) substitution on Ca site in calcium copper titanate (CaCu₃Ti₄O₁₂), and its effect on resulting electrical and dielectric properties has been studied in the present investigation. For this purpose samples were prepared according to two stoichiometries viz. La_xCa_(1−3x/2)Cu₃Ti₄O₁₂ (x ≤ 0.09) and La_xCa_(1−x)Cu₃Ti₄O₁₂ (x = 0.03) by solid state ceramic route. The former represents ionic compensation while the later is in accordance with electronic compensation. Nature of charge carriers is identified by measuring Seebeck coefficient which is found to be negative in the entire range of measurement. In order to understand the mechanism of conduction, ac conductivity is measured as a function of temperature and frequency. Space charge polarization is the dominant polarization mechanism phenomenon at low frequency and high temperature while orientation polarization dominates at low temperature and high frequency. Impedance analysis confirms the formation of internal barrier layers which is responsible for high dielectric constant in these samples.     

High-dielectric-constant and low-loss microwave dielectric in the (1 − x)La(Mg0.5Ti0.5)O3-x(Ca0.8Sr0.2)TiO3 solid solution system

The microwave dielectric properties and microstructures of (1 − x)La(Mg_0.5Ti_0.5)O₃-x(Ca_0.8Sr_0.2)TiO₃ ceramics, prepared by a mixed oxide route, have been investigated. The forming of solid solutions was confirmed by the XRD patterns and the measured lattice parameters for all compositions. A near zero τ_f was achieved for samples with x = 0.5, although the dielectric properties varied with sintering temperature. The Q × f value of 0.5La(Mg_0.5Ti_0.5)O₃-0.5(Ca_0.8Sr_0.2)TiO₃ increased up to 1475 °C, after which it decreased. The decrease in dielectric properties was coincident with the onset of rapid grain growth. The optimum combination of microwave dielectric properties was achieved at 1475 °C for samples where x = 0.5 with a dielectric constant ?_r of 47.12, a Q × f value of 35,000 GHz (measured at 6.2 GHz) and a τ_f value of −4.7 ppm/°C.     

Synthesis and functional properties of the Ni1−xMnxFe2O4 ferrites

Nanocrystalline Ni_1−xMn_xFe₂O₄ (x = 0; 0.17; 0.34; 0.5) ferrite powders were successfully synthesized using the sol-gel combustion method, by using nitrates as cations source and citric acid (C₆H₈O₇) as combustion/chelating agent. The reaction advancement was observed by means of IR absorption spectroscopy, by monitoring two characteristic bands for the spinel compounds at about 600 cm⁻¹ and 400 cm⁻¹, respectively. The as-synthesized powders were characterized by IR spectroscopy, X-ray diffraction (XRD) and scanning electronic microscopy (SEM). The magnetic study shows that the saturation magnetization decreases with increasing the Mn addition, as result of the particle size reduction. The dielectric properties were measured as a function of frequency in the range of 10 Hz to 1 MHz. The real part of permittivity has values of ∼88 at 1 kHz and ∼7 at 1 Hz for x = 0. An increasing dielectric permittivity with increasing the amount of Mn is observed. For all the investigated compositions, both the real and imaginary parts of permittivity decrease with frequency.     

Microwave dielectric properties of temperature stable Li2ZnxCo1−xTi3O8 ceramics

The Li₂Zn_xCo_1−xTi₃O₈ (x = 0.2-0.8) solid solution system has been synthesized by the conventional solid-state ceramic route and the effect of Zn substitution for Co on microwave dielectric properties of Li₂CoTi₃O₈ ceramics has also been investigated. The microwave dielectric properties of these ceramics show a linear variation between the end members for all compositions. The optimized sintering temperatures of Li₂Zn_xCo_1−xTi₃O₈ ceramics increase with increasing content of Zn. The specimen with x = 0.4 sintered at 1050 °C/2 h exhibits an excellent combination of microwave dielectric properties with ?_r = 27.7, Q_u × f = 57,100 GHz and τ_f = −1.0 ppm/°C.     

Dielectric relaxation behaviors of pure and Pr6O11-doped CaCu3Ti4O12 ceramics in high temperature range

Pure and Pr₆O₁₁-doped CaCu₃Ti₄O₁₂ (CCTO) ceramics were prepared by conventional solid-state reaction method. The compositions and structures were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The influences of Pr-ion concentration on dielectric properties of CCTO were measured in the ranges of 60 Hz-3 MHz and 290-490 K. The third phase of Ca₂CuO₃ was observed from the XRD of CCTO ceramics. From SEM, the grain size was decreased obviously with high valence Pr-ion (mixing valence of Pr³⁺ and Pr⁴⁺) substituting Ca²⁺. The room temperature dielectric constant of Pr-doped CCTO ceramics, sintered at 1323 K, was an order of magnitude lower than the pure CCTO ceramics due to the grain size decreasing and Schottky potential increasing. The dielectric spectra of Pr-doped CCTO were flatter than that of pure CCTO. The loss tangent of Pr-doped CCTO ceramics was less than 0.20 in 2 × 10²-10⁵ Hz region below 440 K. The complex impedance spectra of pure and Pr-doped CCTOs were fitted by ZView. From low to high frequency, three semicircles were observed corresponding to three different conducting regions: electrode interface, grain boundary and grain. By fitting the resistors R and capacitors C, the activation energies of grain boundary and electrode contact were calculated. All doped CCTOs showed higher activation energies of grain boundary and electrode than those of pure CCTO ceramics, which were concordant with the decreasing of dielectric constant after Pr₆O₁₁ doping.     

Improved dielectric and non-ohmic properties of Ca2Cu2Ti4O12 ceramics prepared by a polymer pyrolysis method

Non-ohmic and dielectric properties of Ca₂Cu₂Ti₄O₁₂ (CaCu₃Ti₄O₁₂/CaTiO₃ composite) ceramics prepared by a polymer pyrolysis method (PP-ceramic samples) are investigated. The PP-ceramics show a highly dense structure and improved non-ohmic and dielectric properties compared to the ceramics obtained by a solid state reaction method (SSR-ceramic samples). ?′ (tan δ) of the PP-ceramic samples is found to be higher (lower) than that of the SSR-ceramic samples. Interestingly, the PP-ceramic sintered at 1050 °C for 10 h exhibits the high ?′ of 2530 with weak frequency dependence below 1 MHz, the low tan δ less than 0.05 in the frequency range of 160 Hz-177 kHz, and the little temperature coefficient, i.e., |Δ?′| ≤ 15 % in the temperature range from −55 to 85 °C. These results indicate that the CaCu₃Ti₄O₁₂/CaTiO₃ composite system prepared by PP method is a promising high-?′ material for practical capacitor application.     

Phase evolution, crystal structure and dielectric behavior of (1 − x)Nd(Zn0.5Ti0.5)O3 + xBi(Zn0.5Ti0.5)O3 compound ceramics

The phase evolution, crystal structure and dielectric properties of (1 − x)Nd(Zn_0.5Ti_0.5)O₃ + xBi(Zn_0.5Ti_0.5)O₃ compound ceramics (0 ≤ x ≤ 1.0, abbreviated as (1 − x)NZT-xBZT hereafter) were investigated. A pure perovskite phase was formed in the composition range of 0 ≤ x ≤ 0.05. The B-site Zn²⁺/Ti⁴⁺ 1:1 long range ordering (LRO) structure was detected by both XRD and Raman spectra in x ≤ 0.05 samples. However, this LRO structure became gradually degraded with an increase in x. The dielectric behaviors of the compound ceramic at various frequencies were investigated and correlated to its chemical composition and crystal structure. A gradually compensated τ_f value was obtained in (1 − x)NZT-xBZT microwave dielectrics at x = 0.03, which was mainly due to the dilution of dielectric constant in terms of Claussius-Mossotti differential equation.     

Piezoelectric and dielectric properties of Dy2O3-doped (Bi0.5Na0.5)0.94Ba0.06TiO3 lead-free ceramics

(Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ + x wt% Dy₂O₃ with x = 0-0.3 ceramics were synthesized by conventional solid-state processes. The effects of Dy₂O₃ on the microstructure, the piezoelectric and dielectric properties were investigated. X-ray diffraction pattern confirmed that the coexistence of tetragonal and rhombohedral phases in the (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ composition was not changed by adding 0.05-0.3 wt% Dy₂O₃. SEM images indicate that all the ceramics have pore-free microstructures with high density, and that doping of Dy₂O₃ inhibits the grain growth of the ceramics. The addition of Dy₂O₃ shows the double effects on decreasing the piezoelectric and dielectric properties for 0 < x < 0.15 when Dy³⁺ ions substitute B-site Ti⁴⁺ ions, and increasing the properties for 0.15 < x < 0.3 when Dy³⁺ ions enters into A-site of the perovskite structure. The optimum electric properties of piezoelectric constant d₃₃ = 170 pC/N and the dielectric constant ?_r = 1900 (at a frequency of 1 kHz) are obtained at x = 0.3.     

Dielectric and magnetic behavior of BaCd2−xSrxFe16O27 W-type hexagonal ferrites

We have prepared BaCd_2−xSr_xFe₁₆O₂₇ (x = 0, 0.5, 1, 1.5 and 2.0) W-type hexagonal ferrites by standard ceramic method. In this work, the structural, dielectric and magnetic properties have been studied of the prepared samples. The XRD analysis of the samples reveals single phase behavior sintered at 1400 °C for 6 h. The saturation magnetization (M_s) shows increasing behavior with the increasing concentration of Sr²⁺. While the coercivity (H_c) decreases rapidly up to 409 G for x = 1.5 and then increases for (x > 1.5) due to the preference of Cd²⁺ for tetrahedral sites and the number of spin-down magnetic ions. The real and imaginary parts of the dielectric constant (?′,?″) and dielectric loss tangent (tan δ) are determined in the frequency range 0.1-10⁷ Hz. It is observed that both the real and imaginary parts of the dielectric constant and tan δ decrease with the increasing concentration of Sr²⁺, which is due to the contribution of Cd²⁺ ions in addition to Fe³⁺ and Fe²⁺ ions to interfacial polarization.     

Synthesis, structural and microwave dielectric properties of Al2W3−xMoxO12 (x = 0-3) ceramics

Low dielectric ceramics in the Al₂W_3−xMo_xO₁₂ (x = 0-3) system have been prepared through solid state ceramic route. The phase purity of the ceramic compositions has been studied using powder X-ray diffraction (XRD) studies. The microstructure of the sintered ceramics was evaluated by Scanning Electron Microscopy (SEM). The crystal structure of the ceramic compositions as a result of Mo substitution has been studied using Laser Raman spectroscopy. The microwave dielectric properties of the ceramics were studied by Hakki and Coleman post resonator and cavity perturbation techniques. Al₂Mo_xW_3−xO₁₂ (x = 0-3) ceramics exhibited low dielectric constant and relatively high unloaded quality factor. The temperature coefficient of resonant frequency of the compositions is found to be in the range −41 to −72 ppm/°C.     

Structural, magnetic and dielectric properties of La2−xCaxNiO4+δ (x = 0, 0.1, 0.2, 0.3)

The synthesis, structural, magnetic and dielectric properties of a new type of high permittivity materials La_2−xCa_xNiO_4+δ (x = 0, 0.1, 0.2, 0.3) (abbreviated as LCNs) were reported. The samples were prepared through conventional solid state reaction route. Detailed structural information was retrieved by Rietveld refinement; normalized bond length and bond valence was calculated to investigate the compression/dilation effect of bonds and atoms in unit cell. It can be found all samples belong to K₂NiF₄ structure with space group I4/mmm. Doping of Ca in La₂NiO_4+δ shrinks the unit cell and makes the structure tend to become instable. Three types of (La, Ca)-O bonds, and two kinds of Ni-O bonds exist in LCNs. Along c axis there are alternately compressed (La,Ca)O₉ dodecahedra and lengthened NiO₆ octahedra. Room temperature magnetic measurements show that the materials are paramagnetic and Ca doping can improve the spontaneous magnetization. Furthermore, all samples have colossal values of the dielectric constant (?) at frequencies lower than 1 kHz. Interestingly, La_1.8Ca_0.2NiO_4+δ maintains its high permittivity at frequencies up to 1 MHz while La_1.7Ca_0.3NiO_4+δ has the lowest dielectric loss (tan δ). Calcium doping can effectively enhance ? and inhibit tan δ. The distortion of (La,Ca)O₉ dodecahedra can well explain their dielectric properties.     

Origin of giant dielectric constant in Ba[(Fe1−xCox)1/2Nb1/2]O3

The X-ray diffraction Rietveld refinement of Ba[(Fe_1−xCo_x)_1/2Nb_1/2]O₃ with 0 ≤ X ≤ 1 shows cubic structure formation with space group P_m3_m. No distinct tilting of oxygen octahedron is observed. The dielectric measurement of such a cubic system exhibited giant values (?′ > 10⁴) in the temperature range of 298-483 K and frequency range of 10²-10⁵ Hz. An analysis of the permittivity, electric modulus, and electrical conductivity properties in these systems confirmed the presence of oxygen vacancies induced dipolar relaxation. Our investigations show that the observed extremely high dielectric constant values are predominantly the result of oxygen vacancies induced dipoles produced at the grain boundaries. Additional significant intrinsic contributions to the permittivity comes from the directly doped electrons at the unit cell, as indicated by the enhancement in the observed values of the permittivity on replacement of Fe³⁺ (3d⁵) by Co³⁺ (3d⁶). The contributions of the doped free charges and the oxygen vacancy induced dipoles are separated using the Jump Relaxation Model.     

Dielectric properties of Cu substituted Ni0.5−xZn0.3Mg0.2Fe2O4 ferrites

Dielectric properties of Cu substituted Ni-Zn-Mg ferrite samples having the general formula Ni_0.5−xCu_xZn_0.3Mg_0.2Fe₂O₄ (where x = 0.0, 0.1, 0.2, 0.3, 0.4, and 0.5) synthesized by Pramanik method are reported. The single phase formation of the ferrites was confirmed by XRD technique. The lattice parameter is found to increase with increase in Cu content. Average grain size, obtained from SEM micrographs, is found to increase with increase in Cu content. Dielectric parameters were measured as a function of frequency at room temperature as well as at higher temperatures. The variation in dielectric constant (?′) with temperature at four different fixed frequencies viz. 1 kHz, 10 kHz, 100 kHz, and 1 MHz was also studied. The room temperature dielectric constant (?′) and dielectric loss (tan δ) are found to decrease with increase in frequency. The ac conductivity (σ_ac) is found to increase with increase in the frequency.     

Crystal structure and dielectric properties of La(Mg0.5Ti0.5)O3-Ca0.8Sm0.4/3TiO3 solid solution system at microwave frequencies

The crystal structure and the dielectric properties of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ ceramics have been investigated. Ca_0.8Sm_0.4/3TiO₃ was employed as a τ_f compensator and was added to La(Mg_0.5Ti_0.5)O₃ to achieve a temperature-stable material. The formation of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ solid solutions were confirmed by the XRD results and the measured lattice parameters for all compositions. The dielectric properties are strongly correlated to the sintering temperature and the compositional ratio of the specimens. Although the ?_r of the specimen could be boosted by increasing the amount of Ca_0.8Sm_0.4/3TiO₃, it would instead render a decrease in the Q × f. The τ_f value is strongly correlated to the compositions and can be controlled by the existing phases. A new microwave dielectric material 0.45La(Mg_0.5Ti_0.5)O₃-0.55Ca_0.8Sm_0.4/3TiO₃, possessing a fine combination of microwave dielectric properties with an ?_r of 47.83, a Q × f of 26,500 GHz (at 6.2 GHz) and a τ_f of −1.7 ppm/°C, is proposed as a very promising candidate material for today's 3G applications.     

Correlating phase and microstructure development versus dielectric properties in La and Er co-doped Bi4Ti3O12 ferroelectric ceramics

Bi_3.25La_0.75−xEr_xTi₃O₁₂ and Bi_3.25La_0.75Ti_3−xEr_xO_12−δ ceramics were prepared and studied in this work in terms of dopant-induced phase and microstructure development as well as dielectric response. The results show that introduction of Er³⁺ tends to reduce the materials’ sintering temperature and average grain size. Moreover, it was noted that in these systems the substitution site of this dopant is controlled by valence state and ionic radii mismatch effects. In particular, even when a nominal substitution of Ti⁴⁺ is conceived, here it is found that Er³⁺ also incorporates at the (Bi,La)³⁺ sites. These and other interesting concluding remarks from this work, including Er³⁺ tolerance, were possible only after comparing, especially, the X-ray diffraction results and the intrinsic ferroelectric characteristics extracted from the dielectric measurements.     

Dielectric properties and crystal structure of La(Mg1/2Ti1/2)O3 ceramics with Mg substituted by Co

Solid solutions of (1 − x)La(Co_1/2Ti_1/2)O₃-xLa(Mg_1/2Ti_1/2)O₃ were used to prepare La(Mg_1−xCo_x)_1/2Ti_1/2O₃ using solid-state synthesis. X-ray diffraction patterns of the sintered samples revealed single phase formation. A maximum density of 6.01 g/cm³ was obtained for La(Mg_1−xCo_x)_1/2Ti_1/2O₃ (x = 1) ceramics sintered at 1375 °C for 4 h. The maximum values of the dielectric constant (?_r = 29.13) and the quality factor (Q × f = 80,000 GHz) were obtained for La(Mg_1−xCo_x)_1/2Ti_1/2O₃ with 1 wt% ZnO additive sintered at 1375 °C for 4 h. The temperature coefficient of resonant frequency τ_f was −59 ppm/°C for x = 0.3.