Improved dielectric and non-ohmic properties of Ca2Cu2Ti4O12 ceramics prepared by a polymer pyrolysis method

Non-ohmic and dielectric properties of Ca₂Cu₂Ti₄O₁₂ (CaCu₃Ti₄O₁₂/CaTiO₃ composite) ceramics prepared by a polymer pyrolysis method (PP-ceramic samples) are investigated. The PP-ceramics show a highly dense structure and improved non-ohmic and dielectric properties compared to the ceramics obtained by a solid state reaction method (SSR-ceramic samples). ?′ (tan δ) of the PP-ceramic samples is found to be higher (lower) than that of the SSR-ceramic samples. Interestingly, the PP-ceramic sintered at 1050 °C for 10 h exhibits the high ?′ of 2530 with weak frequency dependence below 1 MHz, the low tan δ less than 0.05 in the frequency range of 160 Hz-177 kHz, and the little temperature coefficient, i.e., |Δ?′| ≤ 15 % in the temperature range from −55 to 85 °C. These results indicate that the CaCu₃Ti₄O₁₂/CaTiO₃ composite system prepared by PP method is a promising high-?′ material for practical capacitor application.     

Relationships between Zr substitution for Ti and microwave dielectric properties in Mg(ZrxTi1−x)O3 ceramics

The influence of Zr substitution for Ti on the microwave dielectric properties and microstructures of the Mg(Zr_xTi_1−x)O₃(MZ_xT) (0.01 ≤ x ≤ 0.3) ceramics was investigated. The quality factors of Mg(Zr_xTi_1−x)O₃ ceramics with x = 0.01-0.05 were improved because the solid solution of a small amount of Zr⁴⁺ substitution in the B-site could increase density and grain size. An excess of Zr⁴⁺ resulted in the formation of a great deal of secondary phase that declined the microwave dielectric properties of MZ_xT ceramics. The temperature coefficient of resonant frequency (τ_f) of Mg(Zr_xTi_1−x)O₃ ceramics slightly increased with increasing Zr content, and the variation in τ_f was attributed to the formation of secondary phases.     

Structure and dielectric characterization of xNd(Mg1/2Ti1/2)O3-(1 − x)Ca0.6La0.8/3TiO3 in the microwave frequency range

The crystal structures, phase compositions and the microwave dielectric properties of the xLa(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.8Sr_0.2TiO₃ composites prepared by the conventional solid state route have been investigated. The formation of solid solution is confirmed by the XRD patterns. Doping with B₂O₃ (0.5 wt.%) can effectively promote the densification and the dielectric properties of xNd(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.6La_0.8/3TiO₃ ceramics. It is found that xNd(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.6La_0.8/3TiO₃ ceramics can be sintered at 1375 °C, due to the liquid phase effect of B₂O₃ addition observed by Scanning Electronic Microscopy. At 1375 °C, 0.4Nd(Mg_1/2Ti_1/2)O₃-0.6Ca_0.6La_0.8/3TiO₃ ceramics with 1 wt.% B₂O₃ addition possesses a dielectric constant (?_r) of 49, a Q × f value of 13,000 (at 8 GHz) and a temperature coefficients of resonant frequency (τ_f) of 1 ppm/°C. As the content of Nd(Mg_1/2Ti_1/2)O₃ increases, the highest Q × f value of 20,000 GHz for x = 0.9 is achieved at the sintering temperature 1400 °C.     

Investigation of the microwave dielectric properties of Ca1−xMgxLa4Ti5O17 ceramics for application in coplanar patch antenna

In this paper, the dielectric properties of Ca_1−xMg_xLa₄Ti₅O₁₇ ceramics at microwave frequency have been studied. The diffraction peaks of Ca_(1−x)Mg_xLa₄Ti₅O₁₇ ceramics nearly unchanged with x increasing from 0 to 0.03. Similar X-ray diffraction peaks of Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic were observed at different sintering temperatures. A maximum density of 5.3 g/cm³ can be obtained for Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h. A maximum dielectric constant (_r) and quality factor (Q × f) of Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h are 56.3 and 12,300 GHz (at 6.4 GHz), respectively. A near-zero temperature coefficient of resonant frequency (τ_f) of −9.6 ppm/°C can be obtained for Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h. The measurement results for the aperture-coupled coplanar patch antenna at 2.5 GHz are presented. With this technique, a 3.33% bandwidth (return loss <−10 dB) with a center frequency at approximately 2.5 GHz has been successfully achieved.     

High permittivity and low dielectric loss of the Ca1−xSrxCu3Ti4O12 ceramics

The Ca_1−xSr_xCu₃Ti₄O₁₂ (CSCTO) giant dielectric ceramics were prepared by conventional solid-state method. X-ray diffraction patterns revealed that a small amount of Sr²⁺ (x < 0.2) had no obvious effect on the phase structure of the CSCTO ceramics, while with increasing the Sr²⁺ content, a second phase of SrTiO₃ appeared. Electrical properties of CSCTO ceramics greatly depended on the Sr²⁺ content. The Ca_0.9Sr_0.1Cu₃Ti₄O₁₂ ceramics exhibited a higher permittivity (71,153) and lower dielectric loss (0.022) when measured at 1 kHz at room temperature. The ceramics also performed good temperature stability in the temperature range from −50 °C to 100 °C at 1 kHz. By impedance spectroscopy analysis, all compounds were found to be electrically heterogeneous, showing semiconducting grains and insulating grain boundaries. The grain resistance was 1.28 Ω and the grain boundary resistance was 1.31 × 10⁵ Ω. All the results indicated that the Ca_0.9Sr_0.1Cu₃Ti₄O₁₂ ceramics were very promising materials with higher permittivity for practical applications.     

Multiferroic and magnetoelectric properties of single-phase Bi0.85La0.1Ho0.05FeO3 ceramics

Single-phase Bi_0.85La_0.1Ho_0.05FeO₃ multiferroic ceramics were prepared by a rapid liquid sintering method. The ceramics exhibited an obvious ferroelectric loop with a remnant polarization of 11.2 μC/cm² and also showed weak ferromagnetism with the remnant magnetization of 0.179 emu/g at room temperature. A considerable enhancement of the polarization on magnetic poling and a dielectric anomaly in the vicinity of the antiferromagnetic transition temperature due to the intrinsic magnetoelectric coupling effect were observed in Bi_0.85La_0.1Ho_0.05FeO₃ ceramics. The dielectric constant for the Bi_0.8La_0.1Ho_0.05FeO₃ samples at room temperature decreases with increasing applied magnetic fields, and the coupling coefficient (?′(H) − ?′(0))/?′(0) reaches −1.04% at H = 10 kOe.     

Porous Li4Ti5O12 anode material synthesized by one-step solid state method for electrochemical properties enhancement

A porous Li₄Ti₅O₁₂ anode material was successfully synthesized from mixture of LiCl and TiCl₄ with 70 wt% oxalic acid by a modified one-step solid state method. The anode material Li₄Ti₅O₁₂ exhibited a cubic spinel structure and only one voltage plateau occurred around 1.5 V. The initial capacity of porous Li₄Ti₅O₁₂ was 167 and 133 mAh g⁻¹ at 0.5 and 1C charge/discharge rate, respectively, and the capacity retention maintained above 98% after 200 cycles. The porous Li₄Ti₅O₁₂ structure showed promising rate performance with a capacity of 70 mAh g⁻¹ at charge/discharge 10C rate after 200 cycles. It was demonstrated that the porous structure could withstand 50C charge/discharge rate and exhibited excellent cycling stability.     

Piezoelectric and dielectric properties of Dy2O3-doped (Bi0.5Na0.5)0.94Ba0.06TiO3 lead-free ceramics

(Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ + x wt% Dy₂O₃ with x = 0-0.3 ceramics were synthesized by conventional solid-state processes. The effects of Dy₂O₃ on the microstructure, the piezoelectric and dielectric properties were investigated. X-ray diffraction pattern confirmed that the coexistence of tetragonal and rhombohedral phases in the (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ composition was not changed by adding 0.05-0.3 wt% Dy₂O₃. SEM images indicate that all the ceramics have pore-free microstructures with high density, and that doping of Dy₂O₃ inhibits the grain growth of the ceramics. The addition of Dy₂O₃ shows the double effects on decreasing the piezoelectric and dielectric properties for 0 < x < 0.15 when Dy³⁺ ions substitute B-site Ti⁴⁺ ions, and increasing the properties for 0.15 < x < 0.3 when Dy³⁺ ions enters into A-site of the perovskite structure. The optimum electric properties of piezoelectric constant d₃₃ = 170 pC/N and the dielectric constant ?_r = 1900 (at a frequency of 1 kHz) are obtained at x = 0.3.     

Effect of Ag-doping on crystal structure and high temperature thermoelectric properties of c-axis oriented Ca3Co4O9 thin films by pulsed laser deposition

Ag-doped Ca₃Co₄O₉ thin films with nominal composition of Ca_3−xAg_xCo₄O₉ (x = 0∼0.4) have been prepared on sapphire (0 0 0 1) substrates by pulsed laser deposition (PLD). Structural characterizations and surface chemical states analysis have shown that Ag substitution for Ca in the thin films can be achieved with doping amount of x ≤ 0.15; while x > 0.15, excessive Ag was found as isolated and metallic species, resulting in composite structure. Based on the perfect c-axis orientation of the thin films, Ag-doping has been found to facilitate a remarkable decrease in the in-plane electrical resistivity. However, if doped beyond the substitution limit, excessive Ag was observed to severely reduce the Seebeck coefficient. Through carrier concentration adjustment by Ag-substitution, power factor of the Ag-Ca₃Co₄O₉ thin films could reach 0.73 mW m⁻¹ K⁻² at around 700 K, which was about 16% higher than that of the pure Ca₃Co₄O₉ thin film.     

Enhancement microwave dielectric properties of La(Mg0.5Sn0.5)O3 ceramics by substituting Mg with Ni

The microwave dielectric properties of La(Mg_0.5−xNi_xSn_0.5)O₃ ceramics were examined with a view to their exploitation for mobile communication. The La(Mg_0.5−xNi_xSn_0.5)O₃ ceramics were prepared by the conventional solid-state method at various sintering temperatures. The X-ray diffraction patterns of the La(Mg_0.4Ni_0.1Sn_0.5)O₃ ceramics revealed no significant variation of phase with sintering temperatures. Apparent density of 6.71 g/cm³, dielectric constant (?_r) of 20.19, quality factor (Q × f) of 74,600 GHz, and temperature coefficient of resonant frequency (τ_f) of −85 ppm/°C were obtained for La(Mg_0.4Ni_0.1Sn_0.5)O₃ ceramics that were sintered at 1550 °C for 4 h.     

Dielectric relaxation behaviors of pure and Pr6O11-doped CaCu3Ti4O12 ceramics in high temperature range

Pure and Pr₆O₁₁-doped CaCu₃Ti₄O₁₂ (CCTO) ceramics were prepared by conventional solid-state reaction method. The compositions and structures were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The influences of Pr-ion concentration on dielectric properties of CCTO were measured in the ranges of 60 Hz-3 MHz and 290-490 K. The third phase of Ca₂CuO₃ was observed from the XRD of CCTO ceramics. From SEM, the grain size was decreased obviously with high valence Pr-ion (mixing valence of Pr³⁺ and Pr⁴⁺) substituting Ca²⁺. The room temperature dielectric constant of Pr-doped CCTO ceramics, sintered at 1323 K, was an order of magnitude lower than the pure CCTO ceramics due to the grain size decreasing and Schottky potential increasing. The dielectric spectra of Pr-doped CCTO were flatter than that of pure CCTO. The loss tangent of Pr-doped CCTO ceramics was less than 0.20 in 2 × 10²-10⁵ Hz region below 440 K. The complex impedance spectra of pure and Pr-doped CCTOs were fitted by ZView. From low to high frequency, three semicircles were observed corresponding to three different conducting regions: electrode interface, grain boundary and grain. By fitting the resistors R and capacitors C, the activation energies of grain boundary and electrode contact were calculated. All doped CCTOs showed higher activation energies of grain boundary and electrode than those of pure CCTO ceramics, which were concordant with the decreasing of dielectric constant after Pr₆O₁₁ doping.     

Effect of CaTiO3 addition on microwave dielectric properties of Mg2(Ti0.95Sn0.05)O4 ceramics

The microwave dielectric properties of CaTiO₃-added Mg₂(Ti_0.95Sn_0.05)O₄ ceramics prepared by the mixed oxide route have been investigated. The combination of spinel-structured Mg₂(Ti_0.95Sn_0.05)O₄ and perovskite-structured CaTiO₃ forms a two-phase system (1 − x)Mg₂(Ti_0.95Sn_0.05)O₄-xCaTiO₃, which was confirmed by the XRD patterns and the EDX analysis and it also leads to a zero τ_f. The microwave dielectric properties of the ceramics can be effectively controlled by varying the x value. For practical applications, a new microwave dielectric material 0.91Mg₂(Ti_0.95Sn_0.05)O₄-0.09CaTiO₃ is suggested and it possesses a good combination of dielectric properties with an ?_r of ∼18.01, a Q × f of ∼92,000 GHz, and a τ_f of ∼0 ppm/°C, which makes it is a very promising candidate material for high frequency applications.     

Preparation, structure and electrical conductivity of the pyrochlore-type phase Sm2Zr2O7 codoped with bivalent magnesium and trivalent dysprosium cations

The pyrochlore-type phases with the compositions of SmDy_1−xMg_xZr₂O_7−x/2 (0 ≤ x ≤ 0.20) have been prepared by pressureless-sintering method for the first time as possible solid electrolytes. The structure and electrical conductivity of SmDy_1−xMg_xZr₂O_7−x/2 ceramics have been studied by the X-ray diffraction (XRD), scanning electron microscopy (SEM) and impedance spectroscopy measurements. SmDy_1−xMg_xZr₂O_7−x/2 (x = 0, 0.05, 0.10) ceramics exhibit a single phase of pyrochlore-type structure, and SmDy_1−xMg_xZr₂O_7−x/2 (x = 0.15, 0.20) ceramics consist of pyrochlore phase and a small amount of the second phase magnesia. The total conductivity of SmDy_1−xMg_xZr₂O_7−x/2 ceramics obeys the Arrhenius relation, and the total conductivity of each composition increases with increasing temperature from 673 to 1173 K. SmDy_1−xMg_xZr₂O_7−x/2 ceramics are oxide-ion conductors in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest total conductivity value is about 8 × 10⁻³ S cm⁻¹ at 1173 K for SmDy_1−xMg_xZr₂O_7−x/2 ceramics.     

Crystal structure and dielectric properties of La(Mg0.5Ti0.5)O3-Ca0.8Sm0.4/3TiO3 solid solution system at microwave frequencies

The crystal structure and the dielectric properties of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ ceramics have been investigated. Ca_0.8Sm_0.4/3TiO₃ was employed as a τ_f compensator and was added to La(Mg_0.5Ti_0.5)O₃ to achieve a temperature-stable material. The formation of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ solid solutions were confirmed by the XRD results and the measured lattice parameters for all compositions. The dielectric properties are strongly correlated to the sintering temperature and the compositional ratio of the specimens. Although the ?_r of the specimen could be boosted by increasing the amount of Ca_0.8Sm_0.4/3TiO₃, it would instead render a decrease in the Q × f. The τ_f value is strongly correlated to the compositions and can be controlled by the existing phases. A new microwave dielectric material 0.45La(Mg_0.5Ti_0.5)O₃-0.55Ca_0.8Sm_0.4/3TiO₃, possessing a fine combination of microwave dielectric properties with an ?_r of 47.83, a Q × f of 26,500 GHz (at 6.2 GHz) and a τ_f of −1.7 ppm/°C, is proposed as a very promising candidate material for today's 3G applications.     

High-dielectric-constant and low-loss microwave dielectric in the (1 − x)La(Mg0.5Ti0.5)O3-x(Ca0.8Sr0.2)TiO3 solid solution system

The microwave dielectric properties and microstructures of (1 − x)La(Mg_0.5Ti_0.5)O₃-x(Ca_0.8Sr_0.2)TiO₃ ceramics, prepared by a mixed oxide route, have been investigated. The forming of solid solutions was confirmed by the XRD patterns and the measured lattice parameters for all compositions. A near zero τ_f was achieved for samples with x = 0.5, although the dielectric properties varied with sintering temperature. The Q × f value of 0.5La(Mg_0.5Ti_0.5)O₃-0.5(Ca_0.8Sr_0.2)TiO₃ increased up to 1475 °C, after which it decreased. The decrease in dielectric properties was coincident with the onset of rapid grain growth. The optimum combination of microwave dielectric properties was achieved at 1475 °C for samples where x = 0.5 with a dielectric constant ?_r of 47.12, a Q × f value of 35,000 GHz (measured at 6.2 GHz) and a τ_f value of −4.7 ppm/°C.     

Characterization of sol-gel synthesised lead-free (1 − x)Na0.5Bi0.5TiO3-xBaTiO3-based ceramics

The crystal structure, microstructure, dielectric and ferroelectric properties of (1 − x)Na_0.5Bi_0.5TiO₃-xBaTiO₃ ceramics with x = 0, 0.03, 0.05, 0.07 and 0.1 are investigated. A structural variation according to the system composition was investigated by X-ray diffraction (XRD) analyses. The results revealed that the synthesis temperature for pure perovskite phase powder prepared by the present sol-gel process is much lower (800 °C), and a rhombohedral-tetragonal morphotropic phase boundary (MPB) is found for x = 0.07 composition which showing the highest remanent polarization value and the smallest coercive field. The optimum dielectric and piezoelectric properties were found with the 0.93Na_0.5Bi_0.5TiO₃-0.07BaTiO₃ composition. The piezoelectric constant d₃₃ is 120 pC/N and good polarization behaviour was observed with remanent polarization (P_r) of 12.18 pC/cm², coercive field (E_c) of 2.11 kV/mm, and enhanced dielectric properties ?_r > 1500 at room temperature. The 0.93Na_0.5Bi_0.5TiO₃-0.07BaTiO₃-based ceramic is a promising lead-free piezoelectric candidate for applications in different devices.     

Preparation and characterization of La1−xKxFeO3 (x = 0-1) by self-propagating high-temperature synthesis for use as soot combustion catalyst

This paper proposes La_1−xK_xFeO₃ prepared by self-propagating high-temperature synthesis (SHS) as an alternative to platinum catalysts for promoting diesel soot combustion. The catalytic property of eleven products SHSed with different substitution ratios of potassium (x = 0-1) was experimentally evaluated using a thermobalance. In the mass loss curves of the product, T₅₀ was defined as the temperature at which the weight of the reference soot decreases to half its initial weight. The BET specific surface area of SHSed La_1−xK_xFeO₃ depended on x strongly. All the products showed good oxidation catalytic activity. Despite having the smallest surface area (0.11 m²/g) among the obtained products, La_0.9K_0.1FeO₃ (x = 0.1) was found to be the best catalyst with the lowest T₅₀ (442 °C). T₅₀ of La_1−xK_xFeO₃ decreased with increasing x for x > 0.2. The products with x = 0.6 and 0.8 were the second-best catalysts in terms of their T₅₀. Moreover, average apparent activation energy of La_0.9K_0.1FeO₃ (x = 0.1) calculated by Friedman method using TG was as much as 61 kJ/mol lower than that of Pt/Al₂O₃ catalyst. In conclusion, potassium-substituted SHSed La_1−xK_xFeO₃ can be used as an alternative to Pt/Al₂O₃ for soot combustion.     

Combustion synthesis of Ti3Si1−xAlxC2 solid solutions from TiC-, SiC-, and Al4C3-containing powder compacts

Preparation of the Ti₃Si_1−xAl_xC₂ solid solution with x = 0.2-0.8 was investigated by self-propagating high-temperature synthesis (SHS) using TiC-, SiC-, and Al₄C₃-containing powder compacts. Due to the variation of reaction exothermicity with sample stoichiometry, the combustion temperature and reaction front velocity decreased with increasing Al content of Ti₃Si_1−xAl_xC₂ for the TiC- and Al₄C₃-added samples, but increased for the samples with SiC. In contrast to the formation of Ti₃(Si,Al)C₂ as the dominant phase for the TiC- and SiC-added samples, TiC was identified as the major constituent in the final products of samples adopting Al₄C₃. In addition, the evolution of Ti₃(Si,Al)C₂ was improved by increasing the Al content of the TiC- and SiC-added powder compacts, but deteriorated considerably upon the increase of Al₄C₃ in the Al₄C₃-containing sample.     

Magnetic properties of Al2O3-Cr2O3 solid solutions

Solid solution ceramics (Al₂O₃)_x(Cr₂O₃)_1−x with different x in the range of 0 < x < 1 were synthesized via traditional ceramic production method. X-ray diffraction results and Rietveld refinements indicated that all samples possessed rhomb-centered structure and continuous solid solutions were synthesized. The samples were composed of irregular grains with several micrometers in diameter. Temperature dependence of magnetization measurements showed monotonous decreasing Néel temperature with increasing x and percolation effect happened with threshold of x = 0.65. As x became higher, weak ferromagnetism was observed in the samples. Field dependence of magnetization measurements further confirmed the weak ferromagnetism in the samples with x = 0.7, 0.8 and 0.9.     

Mg-substituted ZnNb2O6-TiO2 composite ceramics for RF/microwaves ceramic capacitors

Microstructure and microwave dielectric properties of Mg-substituted ZnNb₂O₆-TiO₂ microwave ceramics were investigated. Mg acted as a grain refining reagent and columbite phase stabilization reagent. With an increasing Mg content, the amount of ixiolite (Zn, Mg) TiNb₂O₈ decreased, and the amount of (Zn_0.9Mg_0.1)_0.17Nb_0.33Ti_0.5O₂ and columbite increased. ZnO-Nb₂O₅-1.75TiO₂-5 mol.%MgO exhibited excellent dielectric properties (at 950 °C): ?_r = 35.6, Q × f = 16,000 GHz (at 5.6 GHz) and τ_f = −10 ppm/°C. The material was applied successfully to make RF/microwaves ceramic capacitor, whose self-resonance frequency was 19 GHz at low capacitance of 0.13 pF.