渗铝-真空预氧化制备FeAl/Al2O3防氚渗透涂层性能

在核级316L不锈钢基体上,采用固体埋层渗铝和真空预氧化工艺制备FeAl/Al2O3防氚渗透自修复涂层,研究了这种渗铝氧化涂层的表面形貌、化学成分、相组成以及涂层表面纳米级氧化膜的厚度的SEM/EDS、XRD、XPS、AES、RBS等测试分析与表征方法.结果表明:该复合涂层由约20μm厚的Fe-Al扩散层以及约200nm厚的表面Al2O3氧化层组成;Fe-Al扩散层的主要相组成为FeAl及少量Fe3Al、NiAl、α-Fe相,微观观察表明由外渗铝层、过渡层、内扩散层构成.     

火电机组过/再热器锅炉管内壁铝化物涂层研究(Ⅱ):蒸汽氧化、强度及组织演化

目的 分析表征锅炉管内壁铝化物涂层的综合性能。方法 通过动态高温蒸汽氧化实验、高温拉伸试验、高温持久试验和650 ℃/10 000 h热暴露实验，分别评价Super304H锅炉管内壁铝化物涂层的抗蒸汽氧化性能、高温强度、高温持久性能和涂层组织时效稳定性，并通过X射线仪、电子显微镜和能谱技术分析涂层结构与物相、氧化产物和断口特征。结果 采用料浆法可在Super304H锅炉管内壁制备厚度约40 μm的铝化物涂层，涂层以FeAl相为主，且与母材呈冶金结合。在650 ℃、1000 h饱和蒸汽氧化过程中，涂层表面生长极薄的α-Al2O3，氧化膜厚度小于1 μm，抗氧化能力优于表面喷丸Super304H及更高Cr含量的HR3C合金。在650 ℃高温，涂层Super304H合金的强度与断裂韧性与母材相当，持久寿命与母材持平，蠕变断裂位置未发生在涂层一侧。650 ℃长时热暴露过程中，涂层由FeAl相向Fe3Al相退化。结论 涂层制备过程未对合金母材组织有显著影响，铝化物涂层显著提高了Super304H合金650 ℃饱和蒸汽氧化性能，对合金的高温力学性能无显著影响。长时热暴露后，涂层与基体互扩散造成组织退化。     

K4104合金渗Al涂层抗高温氧化性能研究

采用料浆法在K4104合金表面进行热扩散渗铝,经1000℃×200h高温氧化性试验,用扫描电镜观察氧化后涂层的表面形貌。结果表明,渗Al涂层在氧化过程中已转变成连续致密的-αAl2O3氧化层和富铝的-βNiAl化合物层,使基体合金得到有效地保护,渗Al涂层具有良好的抗高温氧化性能。     

一种新型奥氏体Fe-Mn-Al耐热钢铝化物涂层相变的研究

对一种新型奥氏体Fe—Mn—Al耐热钢铝化物涂层的显微结构、组成、相变进行了详细地研究。渗层共分两层,外层为有序超结构固溶体FeAl,内层由FeAl、β-Mn,V_4C_3组成。当这种涂层在静态空气下,在450—750℃温度范围内氧化50—1000小时时,这两层经历着不同的相变规律。外层是:FeAl(→Fe_3Al)→α-Fe→α-Fe+γ→γ。内层是:FeAl+β-Mn(→Fe_3Al+β-Mn)→α-Fe+β-Mn→α-Fe+β-Mn+γ→α-Fe+γ→γ。涂层的相变和涂层的退化紧密相连。贫Al的FeAl相的形成,意味着退化开始。γ的出现,称之促使退化加剧。涂层完全转变成γ,退化即告终。     

火电机组过/再热器锅炉管内壁铝化物涂层研究(Ⅰ)：涂层制备及组织结构

目的在奥氏体不锈钢锅炉管内壁制备抗高温蒸汽氧化涂层。方法采用料浆法在锅炉过/再热器用小口径Super304H不锈钢锅炉管内壁制备铝化物涂层,研究了钢管热处理制度范围内制备工艺(时间、温度)对涂层结构、成分和相组成的影响规律,同时基于扩散定律建立了涂层结构的预测模型。结果铝化物涂层厚度约为30～150μm,与基体冶金结合良好。涂层为双层结构,外层由(Fe,Ni)Al(Cr)相、Cr_xSi_y相以及少量Fe_3Al相组成,互扩散层(IDZ)由(Fe,Ni)Al相、Cr_xSi_y相、点状M_6C碳化物相和针状TCP相组成。涂层的制备温度和保温时间对互扩散层厚度变化影响显著,其随时间和温度的变化曲线近似满足抛物线规律。管材热处理制度范围内的温度过高,易减小涂层外层厚度。结论在匹配Super304H锅炉管热处理工艺的基础上,采用料浆法在小口径Super304H锅炉管内壁获得了双层结构的铝化物涂层。基于Fick第二扩散定律建立了涂层结构控制的预测模型,拟合结果与实验实测数据吻合较好,可为获得不同结构的涂层提供参考。     

渗铝氧化处理对CLAM钢组织和力学性能的影响

采用合适的渗铝氧化处理工艺在CLAM钢基体表面制备了铝化物涂层,然后利用XRD、EPMA、SEM、纳米压痕仪、室温拉伸试验机等手段研究了渗铝氧化处理前后组织和力学性能变化,尤其是涂层的相组成变化,进而详细分析了硬度变化和拉伸断口的断裂机制。结果表明,渗铝氧化处理后在CLAM钢表面形成了由约30.8 μm厚的FeAl相层和约70.7 μm厚的α-Fe(Al)固溶体层组成的铝化物涂层,最外层FeAl相的硬度最大为834.7 HV,由外向内硬度逐渐降低至315.1 HV,基体内部的硬度出现略微回升。CLAM钢在渗铝氧化前后的抗拉强度分别为581.38 MPa和555.83 MPa,断后伸长率分别为30%和28%,断裂模式由渗铝氧化前的韧性断裂变成准解理断裂。由于渗铝及氧化热处理导致的晶粒尺寸增大和第二相粒子聚集,CLAM钢在渗铝氧化后拉伸性能下降,同时在表面涂层处易产生裂纹源从而加速材料断裂。     

机械能助渗铝组织与性能研究

采用金相、EPMA、XRD、TEM分析了冷轧08F钢板600℃机械能助渗铝层组织结构,测试了显微硬度、耐盐水腐蚀、抗高温氧化性和力学性能.结果表明,渗铝层内部组织主要是Fe2Al5相,还存在少量的哪FeAl、Fe3Al等铁铝化合物及非晶态相,未形成晶粒粗大的含铝α-Fe相过渡区.铁、铝氧化合物颗粒呈岛状断续分布在渗层表面.机械能助渗铝层有优良的抗高温氧化性、较高的硬度、良好的耐蚀性,同时渗铝后基体可以保持高的力学性能.     

简单/改性铝化物涂层的研究现状

航空发动机各部件高温结构材料在苛刻环境下服役时,会遭受严重的高温氧化和热腐蚀.在合金表面施加铝化物涂层后,高温下表面能够生成一层致密且生长缓慢的Al2O3氧化膜,从而隔绝腐蚀介质,以防止合金被快速氧化腐蚀.概述了铝化物涂层的优点,包括制备简单、成本低廉.重点综述了以Ni、Fe、Ti/TiAl为合金基体的铝化物涂层微观结构.涂层的微观结构主要由渗铝工艺、基材成分及后处理工艺等因素决定,渗铝工艺包括渗剂成分、渗铝温度和渗铝时间.在高温下渗铝,Al的活度较低,涂层主要以基体元素向外扩散形成外扩散型涂层为主;在低温下渗铝,Al的活度较高,涂层主要以Al向内扩散形成内扩散型涂层为主.还归纳了不同渗铝涂层在干燥空气和水蒸气环境中的高温氧化行为,阐述了水蒸气对铝化物涂层高温氧化行为的影响,比较了Ni-Al系和Fe-Al系涂层的抗高温氧化性能.同时介绍了Cr-Al、Si-Al和Pt-Al 3种改性铝化物涂层的研究进展,包括制备方法、微观结构及抗高温氧化和腐蚀性能.最后,展望并总结了高温防护涂层的发展趋势.     

CLAM钢表面铝化物涂层的制备与铅液相容性研究

目的探索铝化物涂层的制备工艺,研究其是否能有效抑制铅液对CLAM钢的腐蚀。方法用配制的渗剂对CLAM钢进行包埋渗铝,并通过随后的热扩散和原位氧化处理,在CLAM钢表面制备铝化物涂层,研究不同渗铝时间和热扩散时间对涂层厚度的影响。通过静态氧化试验和铅液腐蚀试验,分别评价铝化物涂层的抗氧化性能及其与铅液的相容性,采用XRD、SEM和EPMA分析涂层的相组成以及铅液腐蚀前后的微观形貌和元素分布。结果包埋渗铝+热扩散+原位氧化处理制备的铝化物涂层主要由约30μm的FeAl相层和约70μm的α-Fe(Al)固溶体层组成。在热处理过程中,由于Al和Fe的互扩散现象,涂层中的Fe-Al相依次经过了Fe₂Al₅、FeAl₂、FeAl、Fe₃Al和α-Fe(Al)的转变。在600℃空气中静态氧化120 h后,铝化物涂层试样氧化质量增量为0.028 mg/cm²,比CLAM钢的氧化质量增量降低了1个数量级,铝化物涂层使CLAM钢的氧化动力学曲线由直线规律转变为抛物线规律。经550℃铅液腐蚀600、1800 h后,铝化物涂层的腐蚀质量增量分别为0.058、0.077 mg/cm²,仅约为CLAM钢的1/120。CLAM钢表面产生了疏松多孔的铁氧化物层,而铝化物涂层没有发生明显的腐蚀,但是腐蚀1800 h后,随着表面铝含量的不断消耗,Al₂O₃层厚度逐渐减小。结论铝化物涂层具有良好的抗氧化性能及与铅液的相容性,能够有效抑制铅液对CLAM钢的腐蚀。     

球铁浸镀微弧氧化陶瓷层的制备与组织分析

通过热浸镀铝及微弧氧化的方法在球墨铸铁表面上获得了陶瓷层,并对该涂层进行了XRD、SEM分析.研究结果表明:浸镀温度越高,镀层越厚,直到达到一峰值;浸镀时间越长,镀层越厚.球墨铸铁浸镀微弧氧化获得的涂层由涂层表面至基体依次为陶瓷层、纯铝层、扩散层、基体.陶瓷层主要为Al2O3相,扩散层由FeAl3、Fe2Al5相组成.     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Effect of Short-Time Aging on the Pitting Corrosion Behavior of a Novel Lean Duplex Stainless Steel 2002

The effect of short-time aging in the temperature range between 400 and 1000 °C on the pitting corrosion behavior and mechanical property of a novel lean duplex stainless steel(LDSS) 2002 was investigated through the potentiostatic critical pitting temperature(CPT) tests and the Charpy impact tests. Both the pitting corrosion resistance and the toughness of aged specimens degraded due to the precipitation of detrimental secondary phases and the most significant reduction of CPT and impact energy emerged at 650 °C concurrently. The CPT of LDSS 2002 specimen aged at 650 °C decreased by 28 °C, and the impact energy dropped from 69 to 29 J/cm~2 compared with the solution-annealed sample. Transmission electron microscopy characterization showed that the main precipitates in LDSS 2002 were Cr_2N and M_(23)C_6 along the ferrite–austenite grain boundaries.     

Information for Contributors

正The Transactions of Nonferrous Metals Society of China,founded in 1991 and sponsored by The Nonferrous Metals Society of China,is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology,including mineral processing,extraction metallurgy,metallic materials and heat treatments,metal working,physical metallurgy,powder metallurgy,with the emphasis     

Preface

<正>We are pleased to present this Special Issue of Transactions of Nonferrous Metals Society of China containing selected papers from the First Asian Conference on Aluminum Alloys(ACAA-2013),held in Beijing,China,13–17 October 2013.This conference has been initiated,with approval of     

Information for Contributors

The Transactions of Nonferrous Metals Society of China, founded in 1991 and sponsored by The Nonferrous Metals Society of China, is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology, including mineral processing, extraction metallurgy, metallic materials and heat treatments, metal working, physical metallurgy, powder metallurgy, with the emphasis on fundamental science. It is the unique preeminent publication in English for scientists, engineers, under/post-graduates on the field of nonferrous metals industry. This journal is covered by many famous abstract/index systems and databases such as SCI Expanded, Ei Compendex Plus, 1NSPEC, CA, METADEX, AJ and JICST.