氮化物涂层对钛合金抗循环氧化性能的影响

用多弧离子镀技术在Ti6Al4V钛合金表面沉积Ti_0.5Al_0.5N/Ti_0.7Al_0.3N复合涂层和Ti_0.6Al_0.3Si_0.1N涂层,研究其在550℃~750℃下的抗循环氧化性能。结果表明,TiAlSiN涂层以及Ti_0.5Al_0.5N/Ti_0.7Al_0.3N复合涂层在550℃和650℃氧化后表面形成薄而连续的保护性富铝氧化膜,显著提高了Ti6Al4V的抗氧化性能。在750℃下,TiAlSiN涂层涂敷的Ti6Al4V依然保持着优异的抗循环氧化性能,而Ti_0.5Al_0.5N/Ti_0.7Al_0.3N复合涂层却不能为钛合金提供有效的防护。     

Ti2AlNb合金不同温度下的高温氧化行为

研究了Ti₂AlNb合金在不同温度下的高温氧化行为。采用连续氧化增重的方法计算了合金氧化动力学规律;用XRD、SEM、EDS等手段研究氧化后的表面相结构和表面、截面形貌以及元素分布。结果表明,Ti₂AlNb合金在650 ℃和750 ℃下的连续氧化动力学曲线近似符合抛物线规律,而在850 ℃时符合直线规律。氧化层分层现象明显,且都未形成连续致密的Al₂O₃保护层。氧化产物主要为TiO₂,少量的Al₂O₃、Nb₂O₅,以及微量的AlNbO₄、Nb₂TiO₇、AlNb₂。氧化温度越高,分层越明显,富氧层越厚,危害性氧化物越多。     

Ti6Al4V钛合金表面激光合金化制备Ti-Cu合金层的组织结构

采用激光合金化技术在Ti6Al4V合金基体表面制备了厚度约为120 μm均匀致密连续的Ti-Cu合金层,分析了合金层的元素分布和显微组织结构。结果表明,Ti-Cu合金层中Cu元素随着合金层深度呈梯度分布,在靠近Ti-Cu合金层表面的区域主要是柱状晶夹杂着少量的块状晶,中上部区域主要是生长取向各异且较粗的不发达枝状晶和部分胞状晶,中下部区域主要是生长取向各异的胞状晶,合金层与基材的界面处主要以细小的平面晶为主。合金化层中Cu元素和Ti元素除了形成固溶体外,还形成了Ti₂Cu、Ti₃Cu和Cu₃Al₄等金属间化合物,同时还形成了Cu₃TiO₄和Al₂TiO₅等金属陶瓷相。     

TC4合金表面扩散渗硅涂层的高温氧化行为和失效机制

为提高钛合金的高温抗氧化性能,采用固体粉末扩散渗方法在其表面制备了扩散渗硅涂层,研究了涂层的组织结构、高温氧化行为和失效机制。结果表明,所制备涂层具有致密的多层梯度组织结构,主要由TiSi₂外层,TiSi中间层和Ti₅Si₄+Ti₅Si₃内层组成。高温氧化实验结果表明,涂层在850℃空气中氧化时表面形成了由SiO₂和TiO₂混合组成的保护膜,高温抗氧化性能优良;氧化过程中,涂层与基体合金中Si和Ti的互扩散引起氧化膜内TiO₂含量增加及Si源不足,导致氧化膜保护性变差;氧化产物与涂层之间较高的P-B比、氧化膜与涂层组织间热膨胀系数不匹配导致了氧化膜开裂和剥落。     

一种钴基耐磨材料的高温氧化行为研究

研究了NbC颗粒增强钴基耐磨材料在950～1050℃空气中的氧化行为。合金在950℃下属于抗氧化级，1000℃下属于次抗氧化级，1050℃下属于弱抗氧化级，氧化动力学曲线基本符合抛物线规律。合金表面形成由CoCr₂O₄、CoNb₂O₆、Cr₂O₃和Al₂O₃组成的混合氧化物层，基体中块状NbC的优先原位氧化行为造成氧化层厚度不均匀且疏松多孔。经过1050℃，100 h氧化后，氧化层下方基体中形成贫Cr层，导致氧化皮剥落后无法重新形成具有保护作用的连续氧化膜。     

Si-Al固溶对Ti3AlC2陶瓷300℃干摩擦行为的影响

利用元素粉体热压烧结工艺制备了具有不同Si固溶含量的系列Ti₃Al_1-xSi_xC₂(x=0.2、0.4、0.6)陶瓷材料，采用X射线衍射技术及Rietveld结构精修对所得产物的结构及相组成进行了分析，利用共聚焦显微镜、扫描电子显微镜研究了产物的表面形貌和晶粒结构，使用球-盘型摩擦实验机评估了材料的干摩擦行为。结果表明，Si的引入极大细化了Ti₃Al_1-xSi_xC₂陶瓷的晶粒，并降低其相纯度。随着Si加入量的增加，大量Ti₅Si₃和Ti C杂相出现，Ti₃Al_1-xSi_xC₂陶瓷的硬度逐步提升。而当Si加入量为0.4时，所得Ti₃Al_0.6Si_0.4C₂陶瓷表现出了最低的摩擦系数(COF)，为0....     

等离子喷涂法制备Ti/Ti4O7+TiB2/PbO2阳极材料的性能研究

用等离子喷涂法在钛基体上喷涂一层Ti₄O₇和TiB₂的混合物作为中间过渡层,以提高钛基体的耐蚀性能、改善钛基体的导电性;然后在Ti/Ti₄O₇+TiB₂中间过渡层上电镀PbO₂活性层,从而制备出一种新型的"三明治"结构的钛阳极。实验结果表明:喷涂后的钛基体主要由TiO₂、Ti₄O₇和TiB₂三种物相组成;TiB₂的加入能够显著提高Ti/Ti₄O₇的导电性;当TiB₂含量为15%左右时,该电极材料的电化学性能达到最佳。     

TC4钛合金表面氧化镧催渗渗硼工艺优化

以渗层厚度和表面硬度为评定依据,采用正交试验对TC4钛合金表面氧化镧催渗渗硼工艺进行优化。结果表明,渗硼温度对渗硼层影响最大,其次为渗硼时间、B₄C含量和La₂O₃含量。最优的催渗渗硼工艺为：渗硼温度1050 ℃,渗硼时间20 h,渗硼剂配比20wt%B₄C+4wt%La₂O₃+76wt%SiC。渗层表面由TiB、Ti₂B₅、TiC和Ti组成;与未添加氧化镧渗硼层相比,添加氧化镧渗硼层厚度与表面硬度明显提高,耐磨性也得到显著改善。     

TiAl合金表面热障涂层的高温抗氧化性能研究

利用大气等离子喷涂技术(APS)在TiAl合金基体表面制备TiAl₃/Al₂O₃-13TiO₂纳米热障涂层。采用SEM、EDS和XRD技术分析纳米热障涂层在氧化前后的微观组织及相组成,并对其在950℃下的抗氧化性能进行测试。结果表明,TiAl合金表面制备TiAl₃/Al₂O₃-13TiO₂纳米热障涂层后高温抗氧化性能显著提高,氧化动力学曲线呈对数变化规律,950℃高温氧化时,氧化速率常数为3.7×10^-3 mg²·cm⁴/s。在高温氧化过程中,TiAl₃粘结层与TiAl合金基体之间发生元素扩散,TiAl合金基体与粘结层之间界面消失。在陶瓷层与粘结层之间形成均匀连续的热生长氧化物层(TGO),在TiAl₃粘结层完全降解为TiAl₂相和三元Ti-Al-O化合物后,TGO对陶瓷层和粘结层仍...     

加热温度对10CrNiCuSi钢氧化铁皮的影响

为改善10CrNiCuSi船板钢表面质量粗糙的问题,采用电阻炉开展了1100~1300 ℃高温氧化试验,利用弯曲试验评价了氧化铁皮的剥离性,并研究了不同温度下氧化铁皮的演变规律。结果表明,随着加热温度的升高,氧化速率增大,氧化层厚度明显增加。氧化铁皮主要由Fe₂O₃、Fe₃O₄、FeO和内氧化层组成,而内氧化层主要由FeNiCu、Fe₂SiO₄和FeO相组成。加热过程中Fe₂SiO₄/FeO共晶液相的产生对氧化铁皮的剥离性具有重要影响。在1100 ℃和1150 ℃条件下,内氧化层中的Fe₂SiO₄呈现颗粒状或块状弥散分布,氧化铁皮与基体之间界面平直,氧化铁皮易于剥离;在1200、1250和1300 ℃条件下,Fe₂SiO₄-FeO或Fe₂SiO₄发生熔化形成液相渗入基体和氧化铁皮中,造成界面粗糙,而锚状FeNiCu相与基体及氧化铁皮具有较好的结合力,两者的协同作用造成氧化铁皮难于剥离。因此在1100 ~1150 ℃条件下去除氧化铁皮较为合适。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Effect of Short-Time Aging on the Pitting Corrosion Behavior of a Novel Lean Duplex Stainless Steel 2002

The effect of short-time aging in the temperature range between 400 and 1000 °C on the pitting corrosion behavior and mechanical property of a novel lean duplex stainless steel(LDSS) 2002 was investigated through the potentiostatic critical pitting temperature(CPT) tests and the Charpy impact tests. Both the pitting corrosion resistance and the toughness of aged specimens degraded due to the precipitation of detrimental secondary phases and the most significant reduction of CPT and impact energy emerged at 650 °C concurrently. The CPT of LDSS 2002 specimen aged at 650 °C decreased by 28 °C, and the impact energy dropped from 69 to 29 J/cm~2 compared with the solution-annealed sample. Transmission electron microscopy characterization showed that the main precipitates in LDSS 2002 were Cr_2N and M_(23)C_6 along the ferrite–austenite grain boundaries.     

Information for Contributors

正The Transactions of Nonferrous Metals Society of China,founded in 1991 and sponsored by The Nonferrous Metals Society of China,is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology,including mineral processing,extraction metallurgy,metallic materials and heat treatments,metal working,physical metallurgy,powder metallurgy,with the emphasis     

Preface

<正>We are pleased to present this Special Issue of Transactions of Nonferrous Metals Society of China containing selected papers from the First Asian Conference on Aluminum Alloys(ACAA-2013),held in Beijing,China,13–17 October 2013.This conference has been initiated,with approval of     

Information for Contributors

The Transactions of Nonferrous Metals Society of China, founded in 1991 and sponsored by The Nonferrous Metals Society of China, is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology, including mineral processing, extraction metallurgy, metallic materials and heat treatments, metal working, physical metallurgy, powder metallurgy, with the emphasis on fundamental science. It is the unique preeminent publication in English for scientists, engineers, under/post-graduates on the field of nonferrous metals industry. This journal is covered by many famous abstract/index systems and databases such as SCI Expanded, Ei Compendex Plus, 1NSPEC, CA, METADEX, AJ and JICST.