共查询到20条相似文献,搜索用时 76 毫秒
1.
本文根据汽轮机转子材料30CrMoV钢低周循环疲劳和高温疲劳裂纹扩展试验,用暂态变物性温度热弹塑性有限元对冷态启动工况下的汽轮机转子进行应力场分析结果分别进行无裂纹转子疲劳寿命损耗和转子疲劳裂纹扩展估算,并对估算方法及应力强度因子计算进行了初步分析。 相似文献
2.
汽轮机转子初始裂纹高周疲劳安全性分析方法及其在焊接转子中的应用 总被引:1,自引:1,他引:0
介绍了汽轮机转子高周疲劳寿命的设计方法.提出了汽轮机转子初始裂纹高周疲劳安全性的分析方法,转子高周疲劳的平均应力σm、应力幅σA和应力强度因子范围AKI的计算方法以及转子钢疲劳裂纹扩展门槛值△KR的经验计算公式.给出了汽轮机转子初始裂纹高周疲劳安全性的分析思路、分析方法、评价判据以及半转速1 000 MW核电汽轮机焊接低压转子的高周疲劳安全性分析应用实例.结果表明:转子初始裂纹高周疲劳分析方法能够应用于汽轮机转子的安全性评价,并可以为汽轮机转子的结构优化和长周期安全运行提供依据. 相似文献
3.
加载速率对3OCr1Mo1V汽轮机转子钢低周疲劳特性的影响 总被引:1,自引:1,他引:0
以30Cr1MolV汽轮机转子钢为研究材料,选取0.1%/s、0.3%/s和0.5%/s的加载速率,采用控制总应变的方法,在RDL 05电子蠕变疲劳试验机上研究了加载速率对材料低周疲劳特性的影响.同时,还提出在538℃下加载速率对30Cr1Mo1V汽轮机转子钢应力和低周疲劳寿命影响的关系式以及低周疲劳寿命与总应变幅值的关系式.结果表明:在538℃时,随着加载速率的提高,转子钢循环应力增大,低周疲劳寿命延长;在同一应变下,加载速率越大,所对应的应力幅值越大;随着应变幅值的增大,应力增大,低周疲劳寿命缩短. 相似文献
4.
汽轮机转子钢疲劳—蠕变交互作用 总被引:1,自引:0,他引:1
本文对我国电站汽轮机常用的30Cr2MoV转子钢疲劳—蠕变交互作用进行了试验研究。根据火电厂转子运行工况,选择了不同保载时间,进行裂纹扩展试验。结果表明,这种材料在运行工况下存在疲劳—蠕变交互作用;随着保载时间的增加,裂纹扩展速率增加,寿命大大降低。断口分析发现,断面有沿晶断裂,且呈现“r”型空洞。运用线性累积损伤方法计算该转子钢疲劳—蠕变交互作用系数B=1.47~3.95,提出了交互作用下的裂纹扩展判据。 相似文献
5.
6.
1Cr10Mo1W1NiVNbN钢的蠕变及蠕变-疲劳裂纹扩展行为研究 总被引:2,自引:1,他引:1
采用直流电位法,对国内试制的某超超临界汽轮机高中压转子用1Cr10Mo1W1NiVNbN钢在600℃下的蠕变裂纹、蠕变-疲劳裂纹萌生与扩展行为进行了研究,得到了该钢在不同初始应力强度因子条件下的蠕变裂纹扩展孕育时间关系式和蠕变裂纹扩展速率关系式.研究了不同保持时间对蠕变-疲劳裂纹扩展行为的影响,同时还分析了在不同条件下裂纹扩展行为与时间和循环的相关性.结果表明:疲劳缩短了蠕变-疲劳裂纹的扩展孕育期,加快了裂纹的扩展速度;在栽荷保持时间较短的情况下,蠕变-疲劳裂纹扩展行为与循环相关;而在栽荷保持时间较长的情况下,裂纹扩展行为与时间相关. 相似文献
7.
研究了汽轮机转子钢30Cr2Ni4MoV在各种加载情况下的疲劳裂纹扩展性能,着重研究了频率,载荷比等试验控制量对对裂纹展展的影响,得到了30Cr2Ni4MoV转子钢纹扩展速率的一般关系式,这些关系式与试验数据吻合较好,便于实际应用。 相似文献
8.
9.
10.
在估计汽轮机转子的残余寿命时,除了考虑交变载荷之外,计及蠕变的影响及蠕变和疲劳的相互作用是很重要的。利用非线性有限元程序计算了同一载荷以不同速率加在一个裂纹体上响应,发现对于汽轮机转子常用材料CrMoV钢而言,交变载荷对蠕变的发展几乎没有影响,而蠕变对疲劳的影响取决于加载速率。 相似文献
11.
《International Journal of Hydrogen Energy》2022,47(63):26789-26797
The issues related to the reliability of hydrogen engines of unmanned vehicles and increasing the efficiency of using hydrogen as fuel when using the method of its production during the decomposition of hydrogen-containing molecules of liquid-phase organic compounds in a plasma discharge under the action of intense ultrasonic exposure are considered. Experiments have shown that as a result of decomposition in the acoustoplasma discharge of liquid hydrocarbons, solid-phase carbon-containing products are formed, chemical transformations occur in the liquid phase and hydrogen-containing combustible gas is formed. Hydrogen-containing gas can be used as fuel immediately after synthesis, i.e. it does not require separation, since in addition to hydrogen it contains only impurities of CO2 and water vapor. The purpose of the study is to formalize the basic conditions for tightening the control of mutual compliance with the efficiency of hydrogen engines of the same series in the conditions of their mass production. Methods of mathematical statistics and hardware-software modeling were used in the study. The term “unerroric of quality mutual compliance control” is introduced to describe a set of hardware and software tools for such control. The principle of in-depth testing of the technical condition of such engines of one series is described in a multidimensional formulation of the quality control problem for three of their operating parameters at once. The conditions for increasing the mutual correspondence of the measured values of such parameters in the conditions of serial production of hydrogen engines are formalized. 相似文献
12.
基于《水工混凝土掺用氧化镁技术规范》中的Ⅰ型氧化镁(MgO),研究了该型MgO膨胀剂(MEA)细度对掺粉煤灰水泥浆体膨胀性能的影响。即采用X射线衍射分析(XRD)及同步热分析(TG DSC)分析了掺MEA水泥浆体中MgO的水化性。结果表明,养护温度相同时,MEA的细度对水泥浆体内MEA中MgO的水化和水泥浆体的膨胀无显著影响,产生的膨胀均能补偿水泥浆体的收缩;MEA的细度可从试验设计采用的45 μm筛筛余15%左右增加到30%左右,这将有利于MEA生产企业的节能降耗。 相似文献
13.
14.
15.
应用瞬态谱分析方法对燃烧流化床声波信号进行了频谱分析,发现气泡能量分布呈Gamma分布形式,在Argyrious和Yoshida等人提出的模型的基础上,发展了燃烧流化床气泡能量分布模型,并通过优化迭代对模型参数进行求解,在实验和理论的基础上得出了更加切合实际的燃烧流化床气泡能量分布模型 相似文献
16.
城镇生活污水处理装置是由农村户用沼气地发展演变而来,是一种小型、分散化处理污水的装置 ,是环境建设的需要。文章着重从我国环保政策及目标、生活污水造成的污染状况、急需整治的公共设施、生活污水净化装置的演变以及社会经济效益和环境效益等方面,阐述了其产业化的重要性。 相似文献
17.
介绍了汽轮机零件的封存特点、防锈要求及防锈油性能对比试验的方法,通过对试验结果的对比分析,客观验证了各种防锈油的性能。试验表明,只有选择了合适的防锈油,才能保证汽轮机零件长期封存的质量。 相似文献
18.
19.
The paper deals with second law thermodynamic analysis of a basic gas turbine based gas-steam combined cycle. The article investigates the effect of variation of cycle parameters on rational efficiency and component-wise non-dimensionalised exergy destruction of the plant. Component-wise inefficiencies of the combined cycle have been quantified with the objective to pin-point the major sources of exergy destruction. The parameter that affects cycle performance most is the TIT (turbine inlet temperature). TIT should be kept on the higher side, because at lower values, the exergy destruction is higher. The summation of total exergy destruction of all components in percentage terms is lower (44.88%) at TIT of 1800 K & rp,c = 23, as compared to that at TIT = 1700 K. The sum total of rational efficiency of gas turbine and steam turbine is found to be higher (54.91%) at TIT = 1800 K & rp,c = 23, as compared to that at TIT = 1700 K. Compressor pressure ratio also affects the exergy performance. The sum total of exergy destruction of all components of the combined cycle plant is lower (44.17%) at higher value of compressor pressure ratio (23)& TIT = 1700 K, as compared to that at compressor pressure ratio (16). Also exergy destruction is minimized with the adoption of multi-pressure-reheat steam generator configuration. 相似文献
20.
汽油特性参数间的关系分析 总被引:1,自引:1,他引:1
汽油的特性参数对汽油机的燃烧和排放具有重要影响。通过对市售汽油特性参数间关系的统计分析,得到了汽油密度同汽油的平均氢碳原子数之比和汽油空气混合气的理论空燃比之间的线性关系式。这些统计关系式可用于由测量的汽油密度值推测汽油平均氢碳原子数之比和汽油空气混合气的理论空燃比等,还可用于改善汽油机热计算精度和汽油机空燃比的测量、控制精度。 相似文献