润滑剂对轮轨摩擦与磨损的影响

利用MMS-2A磨损试验机模拟轮轨系统在润滑油、二硫化钼锂基脂、植物油和石墨钙基脂4种润滑剂润滑下的摩擦与磨损行为,研究润滑剂对轮轨副摩擦、磨损特性的影响.结果表明:与干态相比,4种润滑剂均使摩擦副的摩擦因数减小,表面磨痕深度减小,磨损量降低,其中石墨钙基脂的减摩和抗磨效果最好;试验结束后,轮轨试样接触表面的硬度均有不同程度的增加,其中涂有石墨钙基脂的轮轨试样的表面硬度增加最小.     

铁路钢轨损伤机理研究

钢轨损伤一直是铁路运输中的一个关键问题，损伤类型主要是钢轨压溃、侧磨、波磨和剥离，占钢轨损伤量的80％以上。探讨了这几种钢轨的损伤形式，认为钢轨损伤加剧主要是因为轮轨之间表面摩擦力的增加所致；提高钢轨材质是预防钢轨损伤的最主要方法。     

Pin-on-disc study of the effects of railway friction modifiers on airborne wear particles from wheel–rail contacts

Knowledge of wheel–rail interaction is crucial to wheel and rail maintenance. In this interaction, some of the worn-off material is transformed into airborne particles. Although such wear is well understood, few studies treat the particles generated. We investigated friction modifiers' effects on airborne particle characteristics generated in wheel–rail contacts in laboratory conditions. Pin-on-disc machine testing with a round-head pin loaded by a dead weight load 40 N simulated maximum contact pressure over 550 MPa. Airborne particle characteristics were investigated in dry contacts and in ones lubricated with biodegradable rail grease and water- and oil-based friction modifiers. The number of particles declined with the grease; the number of ultrafine particles increased with the water-based friction modifier, mainly due to water vaporization.     

Wheel/rail adhesion: its relation to rail contamination on british railways

An investigation has been made how wheel/rail adhesion varies and how this may be related to railhead contamination. Experiments with oils and water deposited on rails have been carried out. In dry weather adhesion depends on the quantity of oil present, which normally is so small it affects friction by a boundary lubrication mechanism. Evidence suggests that water reduces adhesion from two causes. On debris free rails it acts as an additional boundary lubricant. With debris present it forms a low shear strength mixture which, in minimally wet conditions, remains on the wear band where wheels contact the rail. In steady rain the debris mixture is squeezed aside and adhesion is possibly improved. In dry weather, debris particles have apparently little influence on the overall adhesion coefficient.     

[表面强化及损伤机理]钢轨表面宽带激光淬火工艺及其疲劳磨损性能

针对目前钢轨强化采用的欠速淬火方法存在强化层硬度偏低、耐磨性难以满足重载线路使用要求的问题,使用3种不同光斑宽度的激光,研究了U71Mn材质钢轨的激光淬火强化工艺,获得了不同扫描速度下的临界功率和淬火层深,并测试了淬火层在滚动接触条件下的磨损与接触疲劳性能。结果表明：在临界熔化的激光能量密度下,光斑宽度由6 mm增加到20 mm时,淬火层深度提高了38%,或在获得相同的淬火层深度情况下,处理效率提高6.8倍;淬火层组织为针状马氏体,硬度从原来的300HV提高到800HV以上;20万周次的磨损试验后,激光淬火试样的磨损量只有未处理试样磨损量的25%,未处理试样以表面接触疲劳剥落和塑性变形为主,激光淬火试样仅有轻微的疲劳磨损,耐磨性和抗接触疲劳性能优异。     

车轮滚动接触疲劳与磨耗耦合关系数值模拟

滚动接触疲劳和磨耗是车轮失效的主要方式。通过三维弹性体非赫兹滚动接触理论得到接触斑内的法向、切向应力和材料上不同深度处的最大切应力分布,以CL60钢和贝氏体车轮钢为例,基于"layer"滚动接触疲劳失效模型和Zobory车轮磨耗模型,分析LM型车轮踏面和75 kg.m–1钢轨型面匹配时轮轨接触条件和车轮材质对车轮滚动接触疲劳和磨耗竞争关系的影响。计算结果表明,摩擦因数为0.3时,CL60钢在小蠕滑条件下会发生滚动接触疲劳损伤,在大蠕滑条件下只有轴重大于30 t时才会出现滚动接触疲劳损伤,而贝氏体车轮钢只有在大蠕滑条件且轴重为30 t时,载荷循环次数小于1×105的情况下才会出现滚动接触疲劳损伤;摩擦因数为0.6时,CL60钢和贝氏体车轮钢在各种工况下的滚动接触疲劳损伤速度都小于相同条件下的磨耗速度。     

An investigation of fretting behaviour of several metallic materials under grease lubrication

Fretting wear tests under grease lubrication have been carried out on an aluminium alloy, 52100 steel and low-alloy steel. The sphere–flat contact configuration is used. The influence of the displacement amplitude and normal load is investigated. Comparison between dry and lubricated contact of aluminium alloy, between 52100/52100 steel and 52100/low-alloy steel contact with grease lubrication has been carried out. Results show that grease lubrication strongly affects fretting behaviour. Base oil that separated from the grease during friction may result in accelerated contact wear by fretting.     

A Wear Detection Parameter for the Wheel–Rail Contact Based on Emitted Noise

This article describes how a wheel–rail wear detection parameter based on noise was developed by running a rapid transit train instrumented with microphones in a depot with a small curve radius. This full-scale test made use of previous knowledge gained from lab-scale tests. The lab- and full-scale tests showed that noise could be used as an indicator of wear transition, when normal wear turns into severe or catastrophic wear. This transition was accompanied by a significant increase in sound pressure and a broader sound pressure amplitude spectrum; that is, a narrow initial amplitude distribution in the normal wear regime and a broader distribution in the severe wear regime. The measured noise from the inner/low and outer/high rails was analyzed in conjunction with the wear from the outer wheel and comparisons were made between cleaned (exposed to severe wear) and lubricated (no wear) rail. Based on those analyses, a wear detection parameter criterion was developed for this specific train. This wear parameter has been implemented in a real-time condition monitoring system so that warnings of the risk for severe wear could be sent to the maintenance department. Validation of the wear parameter and challenges linked to open system conditions are discussed in this article.     

Tribochemical Wear of Rail Steels Lubricated with Synthetic Ester-Based Model Lubricants

Headchecks are a common type of damage in heavily loaded curved freight tracks. This paper deals with synthetic ester formulations' ability to prevent damage caused by headchecks through mild tribochemical wear. An experimental study pertaining to wear and friction of two rail steels lubricated by two synthetic ester base fluids, TMP-oleate and TMP-C₈-C₁₀, has been carried out. Six different free fatty acids were used in this study to act as performance additives. Three of the fatty acids were mono-acids with different, straight, carbon chain lengths (stearic acid C₁₈, decanoic acid C₁₀ and octanoic acid C₈), one was a mono-unsaturated straight-chain fatty acid (oleic acid C_18:1) while two were dibasic acids with intermediate carbon chain length (C₉ and C₁₀). Each fatty acid was blended with either ester, one at a time. The tests were carried out by using a high frequency reciprocating friction and wear test machine. In these tests, the gage face/wheel flange contact was simulated, and all tests were conducted in the boundary lubrication regime. An initial contact pressure of 316 MPa and a maximum sliding speed of 0.11 m/s were employed during the tests. The tests showed a wide range of wear rates, as well as different surface features depending on the interactions between synthetic esters, fatty acids and steel. The use of stearic and azaleic acid in lubricating rail steels results in very smooth surfaces with significant differences in their wear rates.     

水介质润滑下车轮钢磨损机制研究

利用往复滚动试验装置,研究了水介质作用下车轮钢的往复滚动摩擦磨损机制.结果表明:接触界面存在水介质条件下的车轮钢摩擦因数明显低于干态工况下的摩擦因数;水介质润滑条件下车轮钢磨损以磨粒磨损为主,水介质的存在减小了车轮钢表面的磨损,同时减轻了车轮钢表面的剥离损伤.     

Tribological properties of plasma nitrided AISI 4140 steel under dry and lubricated sliding conditions

In this investigation, the microstructural, mechanical and tribological properties of plasma and pulse plasma nitrided AISI 4140 steel have been investigated in comparison to hardened steel. The influence of nitriding case depth, as well as the presence of a compound layer, have been tribologically examined for both dry and lubricated sliding. Testing was carried out on a pin‐on‐disc machine in which surface‐treated pins were mated to hardened ball bearing steel discs. The surface treated samples were characterised using metallographic, SEM, microhardness and profilometric techniques, before and after wear testing. The resulting wear loss and coefficient of friction were monitored as a function of load and of test time. The results showed improved tribological properties of the AISI 4140 steel after plasma and pulse plasma nitriding as compared to the hardened steel, in both dry and lubricated sliding. However, the compound layer should be removed from the surface, either by mechanical means or by decreasing the amount of nitrogen in the nitriding atmosphere, in order to avoid impairment of the tribological properties by fracture of the hard and brittle compound layer, followed by formation of hard abrasive particles.     

Wear and friction of synthetic esters in a boundary lubricated journal bearing

This study concerns the case of a slow intermittent motion, conformal contact, high load bronze journal bearing against a hardened steel shaft lubricated in an oil bath at a temperature about of 13 °C. Three synthetic esters were used: one pure and two formulated ones. Worn surfaces were examined using SEM-EDS to determine the wear mechanism. The tested lubricants were examined using ICP-AES to identify the elements present.The results show the wear rate, friction and temperature in the subsurface of the journal bearing material. An initial bronze–steel contact develops into a copper–copper contact along the sliding distance. Wear element concentration in the oil and friction surfaces departs from the elementary concentration in the journal bearing bronze base material. The copper layer thickness depended on additives in the synthetic esters, load and wear rate.     

轮轨接触界面摩擦管理研究进展

列车向着高速与重载方向迅速发展,显著加剧了轮轨接触界面间的损伤。通过在轮轨接触界面进行摩擦管理能够有效地降低轮轨之间的磨损、显著提高列车的运行安全性以及降低运营成本。对轮轨接触界面摩擦管理研究现状进行综述,并介绍轮轨界面摩擦控制对轮轨作用力、黏着、磨耗、滚动接触疲劳以及振动与噪声影响的研究进展;展望了轮轨接触界面摩擦管理未来研究方向,即应针对不同应用环境和接触部位,研发合理的摩擦控制材料,以克服摩擦管理过程中对轮轨损伤及使用局限性等问题;应探究车轮踏面/轨顶面和轮缘/轨距面摩擦控制方式,严格控制摩擦材料喷涂量使两接触面不相互干扰,优化改进轮轨接触界面摩擦管理的最佳应用参数;应研发环境友好型的轮缘/轨距面润滑剂与车轮踏面/轨顶面摩擦控制剂,稳定调控轮轨接触界面的黏着特性。     

曲线半径及轴重对轮轨摩擦功影响的研究

基于非Hertz滚动接触理论利用数值计算方法详细分析了静态接触情况下,轴重和曲线半径对轮轨接触质点间等效应力、接触斑粘滑区的分布、总滑动量和摩擦功的影响。分析计算表明,轴重增加引起轮轨接触质点间等效应力,接触质点间粘滑区的面积以及总滑动量的变化,同时对轮轨接触质点阍的摩擦功的变化有重要影响;小曲线半径处轮轨接触质点间的总滑动量,接触斑滑移区的面积以及摩擦功都明显增大,导致曲线上钢轨磨损加剧。因此曲线半径和轴重是影响轮轨滚动接触磨损的重要因素。     

车轮磨耗计算模型及其数值方法

综述国内外车轮磨耗理论模型及其数值方法,提出基于车辆轨道垂、横向耦合动力学、轮轨滚动接触力学和材料摩擦磨耗模型为一体的车轮磨损计算模型, 并发展相应的数值方法。模型中车辆结构和钢轨下部结构被简化成等效质量、弹簧和阻尼系统, 而钢轨用Euler 梁代替, 并考虑它的垂向、横向弯曲变形和扭转变形。利用修改的KALKER三维弹性体非Hertz 滚动接触理论和相应的数值方法计算轮轨蠕滑力和滑动量等参量;根据Archard材料磨损模型计算车轮的磨耗深度。利用该模型和相应的数值方法分析不同曲线半径情况下车轮的磨损情况,结果表明该模型可以较好地模拟车轮磨损的演化过程。给出列车通过曲线半径为350 m时车轮的磨损情况。数值结果表明,每个转向架下前轮对比后轮对磨耗严重,外轨上的车轮比内轨上的车轮磨耗严重。     

Wear rate testing in relation to airborne particles generated in a wheel–rail contact

This study examines the relationship between generated airborne particles and wear rate in the wheel–rail contact. The wheel–rail contact is experimentally simulated by using pin‐on‐disc testing to determine the difference in wear rate between selected contact conditions. Wear is discussed both in tribological terms and by using the wear categories prevalent in the railway industry, namely, mild, severe and catastrophic wear. The discussion is based on wear depth, the coefficient of friction, topographical measurements and measurements of airborne particles generated in the contact. The tests were performed under selected loading conditions representative of different contact conditions in a real wheel–rail contact. The results indicate that wear rates vary with the contact conditions arising from different types of triggered wear transitions. This is emphasised by the number and size of the airborne particles generated. Copyright © 2009 John Wiley & Sons, Ltd.     

Decarburisation and rolling contact fatigue of a rail steel

Decarburisation is present on all new rails and unless ground off, will be on the running surface once installed. This paper presents a detailed investigation into the effect of decarburisation of rolling contact fatigue and wear. Twin disc testing has been used to study the phenomenon under water-lubricated rolling/sliding contact. Rail discs have been cut from grade 220 rail and heat-treated to give samples with varying depths of decarburisation. It was found that as the depth of decarburisation increased the wear rate of the rail disc increased while that of the wheel disc decreased. The effect of decarburisation on rolling contact fatigue was to increase the crack growth rate of samples with increasing depth. Cracks under rolling contact fatigue were propagated by contact stresses via the fluid pressure mechanism and influenced by microstructure. The effect of decarburisation was predicted to have little effect on rail/wheel contact when scaled from the laboratory tests using the depth of maximum shear stress.     

ANALYSIS OF THERMAL-ELASTIC STRESS OF WHEEL-RAIL IN ROLLING-SLIDING CONTACT

A coupling thermo-mechanical model of wheel/rail in rolling-sliding contact is put forward using finite element method. The normal contact pressure is idealized as the Hertzian distribution, and the tangential force presented by Carter is used. In order to obtain thermal-elastic stress, the ther-mal-elastic plane stress problem is transformed to an elastic plane stress problem with equivalent fictitious thermal body force and fictitious boundary distributed force. The temperature rise and ther-mal-elastic stress of wheel and rail in rolling-sliding are analyzed. The non-steady state heat transfer between the contact surfaces of wheel and rail, heat-convection and radiation between the wheel/rail and the ambient are taken into consideration. The influences of the wheel rolling speed and wear rate on friction temperature and thermal-elastic stress are investigated. The results show the following: ① For rolling-sliding case, the thermal stress in the thin layer near the contact patch due to the friction temperature rise is severe. The higher rolling speed leads to the lower friction temperature rise and thermal stress in the wheel; ② For sliding case, the friction temperature and thermal stress of the wheel rise quickly in the initial sliding stage, and then get into a steady state gradually. The expansion of the contact patch, due to material wear, can affect the friction temperature rise and the thermal stress during wear process. The higher wear rate generates lower stress. The results can help under-stand the influence of friction temperature and thermal-elastic stress on wheel and rail damage.     

Wear mechanisms in oil-lubricated and dry fretting of silicon nitride against bearing steel contacts

The wear and friction behaviour of silicon nitride against bearing steel was investigated under lubricated and dry fretting conditions as a function of amplitude and test duration. Tests were performed on a high frequency fretting tester. Silicon nitride bearing balls were used as the upper oscillating specimens while the lower stationary flats were standard specimens of bearing steel. Amplitudes in the intermediate 5 to 50 μm range and a test duration from 10 to 360 min were studied. In lubricated conditions a commercial lubricant. ISO VG 220, was used. Light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), Auger spectroscopy (AES) and transmission electron microscopy (TEM) were employed to determine the wear mechanisms.

Under lubricated conditions transition from high to low wear volumes was recognised with increasing amplitude. At lower amplitudes and in the early stage of fretting tests at moderate amplitudes, mechanical wear dominated. Cracks on the stick-slip boundary and spalling of a thin tribolayer was observed. Under these conditions the highest wear in lubricated fretting was obtained. In the final stage of fretting tests at moderate amplitudes, and from the beginning at higher amplitude, tribochemical wear is suggested as the dominant wear form. A 0.2 μm thick tribolayer was observed on the contact, containing inclusions with different Fe and Si contents. A very high concentration of carbon, formed by oil degradation, was also determined in this layer, confirming the critical influence of oil on the wear behaviour.

Quite a different wear mechanism is proposed for dry fretting conditions. Results of AES analysis showed a layer an order of magnitude thicker than in lubricated fretting, also having a remarkably different chemical composition. TEM analysis confirmed that the reaction layer consisted of a silica-rich amorphous phase containing small inclusions of Fe₂O₃ and Fe₃O₄. In contrast to lubricated conditions, where the layer created was ductile, in the case of dry fretting the layer was brittle. The continuous process of forming and spalling the brittle tribolayer caused much higher wear rates and wear losses than under lubricated fretting conditions. No transition in wear behaviour was observed as was the case in lubricated fretting.     

轮轨配合对重载货车轮轨磨耗的影响*

在中国既有线路的参数设置下,建立标准LM车轮与R60轨和R75轨配合时的轮轨接触和磨耗模型,对比研究不同轮轨配合时的磨耗性能。计算表明R75轨轮轨接触点集中分布在轨侧、轨头和轨顶三个区域,接触线不连续。在当轮对横移小于3 mm时,两种钢轨滚动圆半径差和接触角差基本一致,轮对横移大于3 mm时,R75轨的滚动圆半径差和接触角差稍小。R75轨与LM车轮配合时,在车轮踏面和轮缘、钢轨轨顶和轨角两段圆弧的过渡段的接触斑面积和应力变化剧烈。车辆在直线上运行时,R75轨的轮轨磨耗将增大数倍,动态通过800 m半径曲线时,外轨磨耗增大约45%。轮轨配合的理论分析表明R75轨不适应我国重载运输,采用提高强度的R60轨更符合我国重载铁路的实际情况。