共查询到20条相似文献,搜索用时 78 毫秒
1.
2.
3.
4.
5.
为了有效解决电路芯片热量过高和温度分布不均匀的问题,结合热管强化传热技术与冷板强化散热技术的优点,研制了基于航空电子设备元器件安装空间尺寸的热管冷板散热装置。利用ICEPAK仿真软件对其进行了热仿真分析,通过比较仿真结果所示的温度云图,确定了热管在冷板上的最佳分布情况,并对冷板上的散热翅片进行优化设计。同时,对仿真结果进行了实验验证,结果表明:所设计的热管冷板散热性能和板面均温性良好,能较好地满足设计要求;ICEPAK热仿真软件计算结果与实验验证结果较为接近,在热设计阶段具有可行性。 相似文献
6.
传统散热冷板以铝合金为主,其导热能力有限且本身密度较大,已无法满足嵌入式计算机对高效散热及轻量化的需求。针对该问题,文中提出将具有超高导热性能的石墨烯散热片粘贴在铝合金表面得到石墨烯–铝复合冷板,以石墨烯–铝复合冷板代替传统散热材料的方法,并对不同厚度、不同功耗下的石墨烯–铝复合冷板的导热效果进行了试验研究。测试结果表明,在铝合金表面贴石墨烯散热片可保证在整体质量增加较小的情况下显著提高冷板的导热能力,在3 mm厚的铝合金表面粘接2 mm厚的石墨烯散热片时导热性能最佳,导热系数达到360 ~ 370 W/(m·K),而质量仅占6 mm厚铝板质量的66.5%。因此石墨烯–铝复合冷板可应用于高性能、高集成、小型化嵌入式计算机的散热设计。 相似文献
7.
8.
9.
拉深模激光毛化表面的磨损性能研究 总被引:1,自引:0,他引:1
为提高拉深模的磨损性能和使用寿命,利用激光毛化技术在模具钢试样表面分别加工出不同直径和间距的微单元体。对比研究毛化表面试样和非毛化表面试样的磨损性能,结果表明,毛化试样表面耐磨性均优于非毛化表面试样。通过激光毛化可提高拉深模寿命,改善板料成形时的流动性。 相似文献
10.
11.
12.
设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率. 相似文献
13.
In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape. 相似文献
14.
15.
通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即:增加导向机构。 相似文献
16.
Polyvinyl pyrrolidone-Iodine complex (PVP-I) molecules were impregnated into the anodic oxide of an aluminum disk specimen. It was rubbed against a silicon nitride ball specimen using a ball-on-disk type friction test rig. Over the limited range of parameters studied (load: 0.2-1.0 N, sliding velocity: 0.6 mm/s, and sliding distance: 1-7 m), the coefficient of friction decreased to a value as low as 0.01 from values of 0.3 to 0.7 for the anodic oxide surface. Single-crystal iodine rubbed against silicon nitride showed a coefficient of friction of 0.1. The low coefficient of friction is attributed to the thin PVP-I film on the relatively hard anodic oxide. The mechanism of coefficient of friction reduction is the same as that of a thin soft film on a hard substrate. 相似文献
17.
18.
针对目前市场对工业设计人才的需求,本文论述了我校在工业设计教育方面的改革措施,着重介绍了我校工业设计教育在软件和硬件方面所进行的一系列的改革。 相似文献
19.
本文以某些积算和双笔记录仪产品为例说明由于仪表功能设计的不合理或选型不当,影响了仪表的正常使用,制造厂和用户应关注这类问题。 相似文献
20.
The article provides a solution to the problem of contraction process modeling when measuring the flow of fluids and gases using differential pressure flowmeters. The article shows the feasibility of obtaining the coefficient of contraction from the mathematical model of the reduced/contracted flow of fluids or gases. An analytical expression is obtained for the coefficient of contraction, which agrees well with the results of the experiment. Analysis of this expression is performed and dependencies on the geometrical parameters of the pipeline and orifice plate are obtained. 相似文献