磨粉机快辊轴承座加工工艺设计

设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率.     

某型号飞机起落架支柱减振筒内壁腐蚀原因分析

飞机起落架减振支柱在飞机起落和滑跑时,吸收撞击能量,对飞机安全起降的意义重大.减振筒是减振支柱中的重要部件,本文从工艺流程、理化分析、外场使用和腐蚀机理分析等方面,对减振支柱减振筒内壁的腐蚀原因及危害进行了综合分析,并提出了相应措施.     

Natural frequencies of vibration of a class of solids composed of layers of isotropic materials

In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape.     

叶切面最大厚度数值计算与应用

以叶切面最大厚度的数值计算方法为基础,探讨叶切面最大厚度计算的计算机实现,介绍叶切面厚度数值计算法的应用实例.     

我校工业设计教育改革初探

针对目前市场对工业设计人才的需求,本文论述了我校在工业设计教育方面的改革措施,着重介绍了我校工业设计教育在软件和硬件方面所进行的一系列的改革。     

两种仪表功能合理性评述

本文以某些积算和双笔记录仪产品为例说明由于仪表功能设计的不合理或选型不当，影响了仪表的正常使用，制造厂和用户应关注这类问题。     

膨胀套导向机构的设计

通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即：增加导向机构。     

串联混合动力牵引车蓄电池SOC的监测

文中提出了基于安时法计算混合动力电动牵引车蓄电池已用电量，在求出当前蓄电池荷电状态的基础上，利用根据能量守恒模型计算出的蓄电池SOC进行荷电状态校正，采用80C196KC加上相应的感应器来实现。实验表明，该方法测出的蓄电池荷电状态比较准确，有较高的精度。     

Effect of Impregnation of Iodine Complex on Friction of Anodic Oxide of Aluminum

Polyvinyl pyrrolidone-Iodine complex (PVP-I) molecules were impregnated into the anodic oxide of an aluminum disk specimen. It was rubbed against a silicon nitride ball specimen using a ball-on-disk type friction test rig. Over the limited range of parameters studied (load: 0.2-1.0 N, sliding velocity: 0.6 mm/s, and sliding distance: 1-7 m), the coefficient of friction decreased to a value as low as 0.01 from values of 0.3 to 0.7 for the anodic oxide surface. Single-crystal iodine rubbed against silicon nitride showed a coefficient of friction of 0.1. The low coefficient of friction is attributed to the thin PVP-I film on the relatively hard anodic oxide. The mechanism of coefficient of friction reduction is the same as that of a thin soft film on a hard substrate.     

双丝杠驱动机构同步分析

介绍了双丝杠驱动机构工作原理,论述了双丝杠运动产生不同步的原因以及如何判定与解决同步问题。     

Modeling of coefficient of contraction of differential pressure flowmeters

The article provides a solution to the problem of contraction process modeling when measuring the flow of fluids and gases using differential pressure flowmeters. The article shows the feasibility of obtaining the coefficient of contraction from the mathematical model of the reduced/contracted flow of fluids or gases. An analytical expression is obtained for the coefficient of contraction, which agrees well with the results of the experiment. Analysis of this expression is performed and dependencies on the geometrical parameters of the pipeline and orifice plate are obtained.     

无线局域网信息安全主流技术的探讨

无线局域网是一种新型的连网技术,于2000年11月在广东省清新县建成并投入使用的“清新县人民政府公众信息网”是我国应用较早，规模较大的无线局域网，它采用了美国LUCEN公司的WAVE POINT II和AP-1000作为主要的无线连接设备，建立了一个既具有远程无线连接，又具有无线漫游功能的大型无线网络，从网络的建设开始，在近3年的管理，维护过程中，课题组根据无线局域网传输媒介特殊性，结合当前信息安全的主流技术，对无线局域网的信息安全问题进行了大量的试验和研究，在总结这些试验结果的基础上，本文针对无线局域网信息安全的主流技术作了一个简要的分析和概述。     

在线修正大型起重机剩余寿命的研究

基于修正Miner疲劳损伤累积理论,采用在线修正的名义应力估算疲劳寿命的方法,设计了一套大型起重机在线寿命预测系统。通过数据的实时测量对剩余寿命进行修正,更好地结合实际,提供了一种准确、实用的预测起重机安全剩余寿命的新手段。     

Method of implementation of the positive gradient of mechanical properties of triboengineering materials

Modern methods of implementation of the rule of positive gradient of mechanical properties are considered; this rule was formulated by I.V. Kragelskii and its application serves to minimize the friction and wear of solids. The given methods include the application of coatings with the method of finishing antifricton abrasion-free treatment; application of new metal-cladding lubricating materials; and creation of a nanostructural state of the surface iron nitride layer by nitriding steel with a positive gradient of hardness normal to the surface.     

液压平衡回路的速度稳定性分析

分析了液压平衡回路稳定性与爬行原因及排除方法。这为排除此类故障以及正确使用和设计平衡回路提供了科学依据。     

某型汽车减振器异响成因分析及技术对策

对汽车减振器的异响成因进行了分析,并提出技术对策。     

一种涡旋压缩机径向随变机构的设计

详细介绍了运用随变原理设计的一种新型径向密封机构的结构特点,工作原理及主要参数的确定方法,该机构可补偿由于涡旋体加工精度不高而造成的功率损失,适用于涡旋压缩机的批量生产。     

铣削图形自动编程系统的研究

介绍了一种铣削图形自动编程系统。该系统以Win2000为平台，以VC6.0为开发工具，以DXF形式读取用Auto-CAD绘制的零件图或工艺图，经过工艺分析和处理，自动生成NC代码，并进行仿真加工。     

偏心轴承磨加工夹具的应用

由于偏心轴承套圈加工比较困难,在加工时,设计了偏心夹具来装卡轴承偏心套。     

热电离质谱计信号放大器非线性校正技术

从理论上研究了热电离质谱计法拉第杯接收器放大器的非线性效应,建立了校正的数学模型。应用该模型,可以用一种同位素标准物质直接检验法拉第接收器放大器的非线性,而不用常规的系列同位素标准物质来检验放大器非线性。应用UTB-500铀同位素标准物质、峰跳扫描质谱测量技术,检验了一台热电离质谱计法拉第接收器放大器的非线性,并对存在的非线性进行了校正。同时,验证了在同位素丰度比值一定的情况下,非线性校正因子是恒定的,它不随离子流信号强度的变化而变化。