共查询到20条相似文献,搜索用时 187 毫秒
1.
根据流体动力润滑理论和系统动力学原理对16V280ZJB型大功率柴油机组合活塞裙部进行摩擦特性研究。由活塞的二阶运动理论建立动力学运动方程,由缸套-活塞裙部流体动力润滑理论和微凸体弹性接触模型建立缸套-活塞裙部摩擦学方程,根据以上两个耦合方程计算出活塞裙部的摩擦力,摩擦功耗以及在主次推力面上的最小油膜承载厚度。以及活塞在不同工况下的横向运动和摇摆运动等动力学结果,对计算的结果进行分析和优化可以降低组合式活塞裙部对气缸套的撞击和摩擦,改善活塞裙部的润滑条件。 相似文献
2.
内燃机活塞裙部二次型线的弹性流体润滑分析 总被引:4,自引:0,他引:4
在对活塞动力学和流体动压润滑行为进行耦合建模的基础上,以椭圆曲线为例分析了二次裙部型线对承压油膜形成的影响,并通过仿真计算考察了活塞裙部二次型线下的油膜力及其在活塞两侧的分布、裙部摩擦损失、活塞二阶运动等.通过分析可知,与直线型裙部型线相比,二次型线具有如下特点:裙都与缸套间的多段楔形有利于形成分布更加合理的多段承压油膜,从而有利于活塞的可靠润滑和导向;活塞裙部摩擦损失有所减小;活塞横向运动速度和位移有明显增加等. 相似文献
3.
考虑活塞裙部润滑状态的活塞二阶运动分析及活塞设计参数的研究 总被引:6,自引:0,他引:6
将活塞的动力学方程与活塞裙部一缸套间流体动力润滑分析相结合,分析了活塞的二阶运动。并从减小活塞的二阶运动和摩擦功耗两个方面研究了活塞结构参数的设计。所获得的结果对实际具有指导意义。 相似文献
4.
活塞是柴油机中的一个重要运动零件,它长期处于高温、高压条件下,作变负荷的往复运动并传递动力。故其工作性能和寿命至关重要。就筒体活塞的基本结构而言,一般可分为:顶面、头部、槽部、裙部和销孔五个部分。它们各有各的功用和要求。本文仅就活塞裙部形状尺寸的标注,提出一些看法,以求和有关同志商讨。由于活塞在气缸中工作时,裙部是导向和承受侧推力的表面,故裙部在整个活塞中占有较大的表面积。另外,销孔的位置也处于裙部范围内,因此,必造成裙部金属材料的分布不均匀。当活塞工作受热膨胀时,由于销孔座部分的金属材料比较集中,其热膨胀量必然比其它部分大,使裙部外圆变形呈 相似文献
5.
基于Pro/E的内燃机活塞裙部精确造型 总被引:1,自引:1,他引:0
精确活塞裙部形状是活塞CAE/CAM的基础。文中研究在Pro/E环境下采用曲线方程控制活塞裙部多个横断面形状,进而完成活塞裙部的精确建模。 相似文献
6.
建立了某型号CO_2活塞压缩机活塞的几何模型,针对裙部进行结构改善,应用ANSYS软件,得到了活塞在热力耦合作用下的变形分析。研究表明:活塞的热力耦合对活塞变形有重要影响,同时活塞变形呈非轴对称分布,变形后裙部外形轮廓形状发生较大变化~([8])。由于活塞裙部形状对活塞润滑特性有重要影响,因此,结果将为活塞的设计改进提供参考。 相似文献
7.
8.
9.
10.
目前活塞裙部润滑分析中一般认为活塞裙部-缸套摩擦副在一个内燃机工作循环所有行程中全部处于充分润滑状况,而实际中当活塞上行(向上止点运动)时,入口处的润滑油量不一定能保证该摩擦副处于充分润滑状况。结合活塞二阶运动模型、流体润滑模型和润滑油流动模型,计算活塞裙部向下(止点)运动后滞留在气缸套壁面上的润滑油量,并以此作为活塞上行期间活塞裙部-缸套摩擦副的润滑油进入量,进行活塞裙部-缸套摩擦副的润滑分析。结果表明,与以往认为所有行程中活塞裙部-缸套摩擦副全部处于充分润滑的分析比较,活塞裙部润滑分析中考虑实际润滑油输送确定活塞上行期间摩擦副的润滑状况时,活塞裙部-缸套摩擦副的润滑性能和活塞二阶运动等都有较明显的变化。 相似文献
11.
12.
In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape. 相似文献
13.
本文以某些积算和双笔记录仪产品为例说明由于仪表功能设计的不合理或选型不当,影响了仪表的正常使用,制造厂和用户应关注这类问题。 相似文献
14.
15.
设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率. 相似文献
16.
针对目前市场对工业设计人才的需求,本文论述了我校在工业设计教育方面的改革措施,着重介绍了我校工业设计教育在软件和硬件方面所进行的一系列的改革。 相似文献
17.
通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即:增加导向机构。 相似文献
18.
19.
Polyvinyl pyrrolidone-Iodine complex (PVP-I) molecules were impregnated into the anodic oxide of an aluminum disk specimen. It was rubbed against a silicon nitride ball specimen using a ball-on-disk type friction test rig. Over the limited range of parameters studied (load: 0.2-1.0 N, sliding velocity: 0.6 mm/s, and sliding distance: 1-7 m), the coefficient of friction decreased to a value as low as 0.01 from values of 0.3 to 0.7 for the anodic oxide surface. Single-crystal iodine rubbed against silicon nitride showed a coefficient of friction of 0.1. The low coefficient of friction is attributed to the thin PVP-I film on the relatively hard anodic oxide. The mechanism of coefficient of friction reduction is the same as that of a thin soft film on a hard substrate. 相似文献
20.