Minimal Realization of Linear Graph Models for Multi-physics Systems

An engineering system may consist of several different types of components,belonging to such physical"domains"as mechanical,electrical,fluid,and thermal.It is t...     

Quantum Cooperative Robotics and Autonomy

The intersection of Quantum Technologies and Robotics Autonomy is explored in the present paper.The two areas are brought together in establishing an interdisci...     

考虑进油孔有限长滑动轴承油膜力的近似解析解

针对具有进油孔的有限长滑动轴承油膜力求解问题,采用变分原理和分离变量法,求得了有限长滑动轴承油膜压力分布的近似解析表达式。将油膜压力分布的近似解析表达式在油膜存在区域上进行积分,即得到了油膜力。将提出的计算有限长滑动轴承油膜力方法与无限长轴承模型、有限元方法的计算结果进行了比较,发现了提出的方法与有限元方法的计算结果很接近。最后,研究了进油孔位置和进油压力对油膜存在区域、油膜力等的影响,研究结果表明进油孔位置和进油压力对油膜存在区域和油膜力有较大的影响。     

三绕组变压器的双绕组等效建模及在Matpower中的应用

针对实际电网存在着大量的三绕组变压器,但国际上一些著名商业软件,如BPA仿真软件、Matpower这一权威潮流计算开源软件,均只提供双绕组变压器模型,限制了其在具有三绕组变压器的电力系统中的应用的问题,潮流计算是自主开发的电力系统各种应用软件的核心模块,因此依托国际权威开源程序进行二次开发,是一种较好的选择。对Matpower要求的数据格式进行了归纳,对变压器的一般的等值电路及带理想变压器的等值电路和带标幺值的等值电路进行了分析研究,提出了三绕组变压器转换为双绕组等效模型的建模方法,使得原先只适应双绕组变压器的潮流计算软件可以适用于三绕组变压器电网的潮流计算;最后以Matpower软件为例进行了案例计算,并用PSASP仿真软件进行对比验证。研究结果证明,所提出的建模方法是有效的。     

On the Relation of Load to Average Gap in the Contact Between Surfaces with Longitudinal Roughness

A computer simulation model for the contact between longitudinally-oriented rough surfaces has been formulated. This model closely duplicates the actual surf ace contact deformation behavior by taking into account the elastic interactions between the asperities. There were no assumptions made about the shapes, or any deformation behavior of the asperities, except for their obeying the laws of elasticity. The plastic deformations on the high asperity peaks were taken into account by setting a ceiling on their contact pressures at the material hardness value. The simulations used real surface profiles which were digitized from unworn circumferentially ground steel surfaces. Each pair of these profiles was mathematically combined to form an equivalent rough profile pressing against an infinitely rigid flat and having the appropriately adjusted elastic modulus. A total of 28 different pairs of profiles were used in the simulations. Each contacting pair was subjected to 30 different load levels and the local contact pressures and deformations were calculated. The contact simulations yielded some important mathematical relationships between parameters, such as the real area of contact, average gap, and average asperity load through statistical curve fitting. Two analytical functions were generated to relate the average load to average gap and the real area of contact to load.     

电站锅炉模糊风险评价方法研究与应用

针对电站锅炉风险等级评价问题,将模糊综合评价技术应用到电站锅炉风险等级评价中。开展了电站锅炉失效影响因素及模糊评价因素的重要程度分析,建立了一套科学合理适于在线评价的电站锅炉风险评价体系,提出了模糊综合评价技术与改进的模糊层次分析法相结合的模糊风险评价方法,利用改进的模糊层次分析法计算了指标体系中各层指标权重。对某一台电站锅炉的实际运行工况影响子因素进行了模糊风险评价,采用模糊合成算子进行模糊综合运算得到电了站锅炉运行工况影响子因素的评价向量。研究结果表明:电站锅炉的运行工况影响子因素的风险评价等级为第6级,失效可能性等级为小,该电站锅炉运行工况良好。     

Non-monotonic material contrast in scanning ion and scanning electron images

30 keV Ga⁺ focused ion beam induced secondary electron (iSE) imaging was used to determine the relative contrast between several materials. The iSE signal compared from C, Si, Al, Ti, Cr, Ni, Cu, Mo, Ag, and W metal layers does not decrease with an increase in target atomic number Z₂, and shows a non-monotonic relationship between contrast and Z₂. The non-monotonic relationship is attributed to periodic fluctuations of the stopping power and sputter yield inherent to the ion–solid interactions. In addition, material contrast from electron-induced secondary electron (eSE) and backscattered electron (BSE) images using scanning electron microscopy (SEM) also shows non-monotonic contrast as a function of Z₂, following the periodic behavior of the stopping power for electron–solid interactions. A comparison of the iSE and eSE results shows similar relative contrast between the metal layers, and not complementary contrast as conventionally understood. These similarities in the contrast behavior can be attributed to similarities in the periodic and non-monotonic function defined by incident particle–solid interaction theory.     

Application of Feature Extraction through Convolution Neural Networks and SVM Classifier for Robust Grading of Apples

This paper proposes a novel grading method of apples,in an automated grading device that uses convolutional neural networks to extract the size,color,texture,an...     

分布动态载荷识别的抗噪处理

针对正交多项式频域法在用多种响应对矩形薄板进行载荷识别中抗噪性较差的问题,综合运用平均法、矩阵预处理和奇异值截断法等方法对之进行改善,并引入空间映射的思想,将该方法的应用范围拓展为复杂的模型.利用仿真算例,证实了该方法具有较好的抗噪性.     

基于MELTAC-N平台的核电厂安全级DCS环网研究与测试

针对工程实践中环网通讯相关问题的处理缺乏理论基础及国产化安全级DCS平台的开发缺乏成熟经验借鉴问题,对基于MELTAC-N平台核电厂安全级DCS环网的软硬件实现进行了研究。提出了安全级DCS环网双环网冗余设计、光切换开关设计等硬件设计方法,以及以RPR协议为基础,采用全数据收发策略的软件设计方法。在CPR1000安全级DCS平台上对安全级DCS环网的可靠性及实时性进行了评价,并进行了容错能力、响应时间及响应时间稳定性测试验证实验。结果表明,基于MELTAC-N平台安全级DCS环网软硬件设计具有较好的容错能力及响应时间稳定性。     

交通荷载作用下桥梁结构参数识别方法

应用动力节点加载法,将作用在桥梁上的交通荷载转化为等效节点荷载,再用两步构造法识别结构物理参数.第1步,用Newmark-β方法变换结构运动方程,并用结构的加速度响应求得变换空间内的位移、速度和加速度响应;第2步,基于最小二乘原理,构造出变换空间内求解结构参数的递推式,进行结构物理参数识别.数值模拟结果表明,在交通荷载作用下,该方法能够快速、准确地进行桥梁结构参数识别.     

基于多目标非支配解提取法的电力系统无功优化

针对传统的电力系统多目标粒子群优化算法采用权重系数法将多目标转化为单目标,从而忽视了各目标函数间的竞争关系这一问题,提出将非支配解提取法运用到电力系统多目标无功优化中,并设定了一套提取规则,以电力系统中的有功网损、电压偏差和电压稳定裕度为目标,使目标在充分竞争的情况下得出Pareto最优解,利用IEEE-14节点系统对多目标非支配解提取法的电力系统无功优化进行了仿真测试。研究结果表明,该算法一次运行可以得出多组非支配解,既有偏向单个目标的解也有兼顾所有目标的解,克服了权重系数法的盲目性和单一性,可使电力决策者根据实际问题选择最优解,具有较好的灵活性与多样性。     

Fractional order nonsingular terminal sliding mode control for flexible spacecraft attitude tracking

This paper investigates a fractional terminal sliding mode control for flexible spacecraft attitude tracking in the presence of inertia uncertainties and extern...     

奥氏体不锈钢表面双辉等离子渗锆的动力学

利用双辉等离子渗金属技术在0Cr18Ni9Ti奥氏体不锈钢表面制备了一层均匀、致密、呈良好冶金结合的渗锆合金层,并对1 060℃下的渗锆动力学进行了研究。结果表明:随着距锆合金层表面距离的增加,锆元素的含量呈梯度递减,扩散系数逐渐减小,而扩散激活能逐步增大;在1 060℃采用双辉等离子技术渗锆时,渗锆合金层表层的空位密度为2.945×(1012~1013)cm-2,与相同温度下采用常规渗金属工艺相比,提高了1~2个数量级。     

气化炉三维扫描测量与数据处理

以德士古气化炉耐火砖的内壁蚀损检测设备为基础,对采集到的点云数据做了进一步处理.通过对数据的筛选和剔除,实现了数据点的平滑降噪细化和精简.然后利用点云对整、网格划分和分色显示等方法,最终完成了内壁腐蚀情况的三维建模.重点讨论了点云数据的预处理及后处理的方法,并根据内壁耐火砖的腐蚀阈值,提出了一种气化炉内壁腐蚀区域的识别与分割方法.对耐火砖的腐蚀分析、气化炉的生产与维修提供了可靠依据,并在工程应用中获得了一致认可.     

Limits of topographic measurement by the scanning tunnelling and atomic force microscopes

Parameters describing the topographic character of a surface (height, surface wavelength, slope and curvature) can be derived from equivalent sinusoidal profiles. The response of a surface-measuring instrument may be modelled in terms of instrument parameters such as stylus radius, and scanning range and resolution. The performance of the instrument may then be mapped as a zone in amplitude-wavelength (AW) space to show the sinusoidal profiles it is capable of measuring. In a first-order analysis the STM and AFM are considered as equivalent to contact-stylus instruments with a notional stylus radius equal to the tip radius plus the gap. Comparisons between different instruments and types of instrument are readily made by mapping in AW space. The error arising from convolution of the sinusoidal profile with that of the finite tip may be quantified and plotted as contours in AW space.     

RLS and LMS blind adaptive multi-user detection method and comparison in acoustic communication

RLS and LMS blind adaptive multi-user detection algorithm and multi-user detector was proposed to solve the problem of multi-user signal detection problem encountered in underwater acoustic communication networks.In simulation analysis,RLS and the LMS blind adaptive multi-user detector were designed and tested for synchronous and asynchronous multi-user communication process.The results of SIR comparison and MMSE comparison show that,both of the two methods can realize blind adaptive detection when any user change in multi-user communication,during this process,the training communication sequences are not needed.The RLS algorithm has about 5 dB higher in SIR compared with LMS algorithm,and the convergence velocity of RLS algorithm is also higher than LMS algorithm when the communication users change.RLS algorithm has better ability in multi-user detection than that of LMS algorithm,and it has great attraction and guiding significance for solving the problem of multiple access interference(MAI) in multi-user communication.     

EXPERIMENTAL RESEARCH AND DESIGN ON HEAT TRANSFER OF EVAPORATOR USED IN THE LARGE QUICK FREEZE PLANT

The evaporator is the main part of a quick-freeze equipment. There are many factors influencing the heat transfer coefficient of an evaporator. The most important factors among them are the fin shape, tube diameter, distance of fin space, frost, and velocity of air flow etc. They mainly influence the thermal efficiency of an evaporator, and therefore its thermal efficiency has direct relationship with the whole efficiency of the quick freeze plant. Evaporators with different structural types have different heat transfer efficiency. In order to obtain high efficiency structure of evaporator, 8 evaporator models with different fin shape, tube diameter and tube arrangement are analyzed and compared. The calculation results show that the integral waved fins, equilateral-triangle arranged small diameter tubes and varying fin-spacing has the highest heat transfer coefficient. The experimental result also shows that the evaporator with this type of structure has better thermal efficiency. The experimental result is in good agreement with the calculation result. It can instruct engineering design for usual designer. A real quick-freeze equipment is designed and put into production. The result shows that, compared with traditional domestic quick-freeze equipments, this equipment decreases by 40% in size and by 20% in energy consumption.     

GENERATE ROUGH TOOL-PATHS FROM UNORGANIZED POINT-CLOUD DIRECTLY

An approach is presented to generate rough interference-free tool-paths directly from massive unorganized data in rough machining that is performed by machining volumes of material in a slice-by-slice manner. Unorganized point-cloud is firstly converted to cross-section data. Then a robust data-structure named tool-path net is constructed to save tool-path data. Optimal algorithms for partitioning sub-cut-areas and computing interference-free cutter-locations are put forward. Finally the tool-paths are linked in a zigzag milling mode, which can be transformed into a traveling sales man problem. The experiment indicates optimal tool paths can be acquired, and high computation efficiency can be obtained and interference can be avoided successfully.     

PHENOMENON OF CARVED DRIVING WHEELS

A newly found phenomenon of carved driving wheels of a rear-wheel-drive tractor used in an airport is discussed. The circum of every driving wheel is damaged at three regions,which distribute regularly and uniformly. Everyday,the tractor tows a trailer which are times heavier than the tractor,and moves on the same road in the airport. The phenomenon is explained by the torsional self-excited vibration system of the powertrain. The simplified torsional vibration system is discribed by a 2-order ordinary differential equation,which has a limit circle. Experiments and numerical simulations show the followings: Because of the heavy trailer,the slip ratio of the tractor’s driving wheels is very large. Therefore,there is severe torsional self-excited vibration in the tractor’s drivetrain,and the self-excited vibration results in severe and regular fluctuations of the rear wheel’s velocity. The severe fluctuations in velocity fastens the damage of the driving wheels. At the same time,the time interval in which an arbitrary point in the circum of the driving wheel contacts with the road twice is two times more than the period of the torsional self-excited vibration,and this times explained the existence of three damaged regions. At last,it points out that the phenomenon can be avoided when the torsional damping is large enough.