Synthesis of Hollow Three-Dimensional Channels LiNi_(0.5)Mn_(1.5)O_4 Microsphere by PEO Soft Template Assisted with Solvothermal Method

A appropriate size with three-dimension(3 D) channels for lithium diffusion plays an important role in constructing highperforming LiNi_(0.5)Mn_(1.5)O_4(LNMO) cathode materials, as it can not only reduce the transport path of lithium ions and electrons, but also reduce the side effects and withstand the structural strain in the process of repetitive Li~+ intercalation/deintercalation. In this work, an e fficient method for designing the hollow LNMO microsphere with 3 D channels structure by using polyethylene oxide(PEO) as soft template agent assisted solvothermal method is proposed. Experimental results indicate that PEO can make the reagents mingle evenly and nucleate slowly in the solvothermal process, thus obtaining a homogeneous distribution of carbonate precursors. In the final LNMO products, the hollow 3 D channels structure obtained by the decomposition of PEO and carbonate precursor in the calcination can provide abundant electroactive zones and electron/ion transport paths during the charge/discharge process, which benefits to improve the cycling performance and rate capability. The LNMO prepared by adding 1 g PEO possesses the most outstanding electrochemical performance, which presented an excellent discharge capacity of 143.1 mAh g~(-1) at 0.1 C and with a capacity retention of 92.2% after 100 cycles at 1 C. The superior performance attributed to the 3 D channels structure of hollow microspheres, which provide uninterrupted conductive systems and therefore achieve the stable transfer for electron/ion.     

Research on Crop Irrigation Schedules Under Deficit Irrigation—A Meta-analysis

Water Resources Management - Increasing water consumption in agriculture due to global climate change has posed considerable challenges to food security, thus improving the efficiency of water...     

基于神经网络和遗传算法的锭子弹性管性能优化

为得到减振弹性管对下锭胆的支承弹性和锭子高速运动下的稳定性等性能的最优匹配效率,依据减振弹性管的等效抗弯刚度及底部等效刚度系数公式,利用MatLab数值分析软件构建弹性管抗弯刚度和底部挠度数学模型。首先,结合Isight优化软件基于径向基神经网络构建其近似模型,且使精度达到可接受水平,并以模型的关键结构参数弹性模量、螺距、槽宽、壁厚为设计变量,结合遗传算法对弹性管抗弯刚度和底部挠度进行多目标优化设计,得到Pareto最优解集和Pareto前沿图,确定出减振弹性管结构工艺参数的优化方案。通过对优化数据进行分析发现,该方案在保证减振弹性管弹性的同时,其底部振幅明显减弱。     

215/70R17.5 10PR 118/116L无内胎半钢载重子午线轮胎的设计

介绍215/70R17.5 10PR 118/116L无内胎半钢载重子午线轮胎的设计。结构设计:外直径741 mm,断面宽204 mm,行驶面宽度164 mm,胎冠曲线采用反向弧设计,胎圈着合直径442.8 mm,胎圈着合宽度178 mm,断面水平轴位置(H_1/H_2)1.0,采用4条纵向花纹沟设计,花纹深度12 mm,花纹饱和度71.3%,花纹周节数63。施工设计:胎面胶采用乳聚丁苯橡胶与顺丁橡胶并用的生胶体系,带束层采用2层2+7×0.28HT钢丝帘线,胎体采用2层2220dtex/2聚酯帘线,胎体上加贴2层锦纶帘布过渡增强层,胎圈采用软、硬两种三角胶,采用二次法成型机成型、B型液压硫化机硫化。成品性能试验结果表明:轮胎的充气外缘尺寸、强度性能、耐久性能和高速性能均达到相关标准要求,胎圈耐久性能显著提高。     

FDC在TFT-LCD中的应用案例研究

针对x因子不明确的品质不良,以TFT-LCD某产品不良为例,提出了FDC大数据分析方法。与实际生产过程相结合,经过数据收集和过滤、数据降维和主成分分析过程,找到该品质不良的强相关因子。通过对强关联因子进行DOE实验设计,明确关键因子管控线,提高产品生产力。     

NMMO法竹纤维拉伸强度的影响因素探讨

以竹浆粕为原料,N-甲基吗啉-N-氧化物(NMMO)水溶液为溶剂,没食子酸正丙酯为抗氧剂,采用湿法纺丝工艺制备竹纤维,讨论了竹浆粕的聚合度、纺丝原液的竹纤维素含量以及抗氧化剂添加量等因素对竹纤维拉伸强度的影响,并通过场发射扫描电子显微镜(FE-SEM)对竹纤维的表面微观形貌进行观察。结果表明:在竹纤维素质量分数为11%～15%、竹浆粕聚合度为450～950、抗氧剂质量分数0～0.5%的条件下,随着竹纤维素含量的增加、竹浆粕聚合度的增大和抗氧化剂添加量的增加,竹纤维的拉伸强度均呈上升趋势;FE-SEM观察发现竹纤维原纤化明显,表面出现明显的表面缺陷。     

The Solutions for Adjustment and Reconstruction of Water-Drive Surface Systems in the Old Areas of Daqing Oilfield

Introduction 　　Owing to long-time running, more facilities including stations, pipelines, vessels have become corrosive and aged ,some process has grown old, it has exert more burden for the maintenance and repair.Simultaneously, the fluid production rate, oil production rate and water injection rate has changed greatly so that the inflicts and problems from the established surface systems will become more obvious. Energy cost of production and running has increasing continuously. Capacity has been unbalance in systems and areas. 　　……