Hydrothermal synthesis of 3D NixCo1−xS2 particles/graphene composite hydrogels for high performance supercapacitors

In this work, three dimensional (3D) Ni_xCo_1−xS₂/graphene composite hydrogels with different Ni contents (denoted as Ni_xCo_1−xS₂/GH (x = 0, 0.31, 0.56, 0.66, 1)) have been synthesized by a simple one-step hydrothermal method and utilized as the active materials of supercapacitors. The as-prepared samples present a 3D interconnected porous network with the pore sizes in the range of several to tens micrometers. Interestingly, the Ni_xCo_1−xS₂ particles are uniformly located on the graphene network and the particle size is evolved from ∼50 nm to ∼1.5 μm with the increase of Ni content. The electrochemical measurements revealed that the specific capacitance, rate capability and cyclability of different Ni_xCo_1−xS₂/GH electrodes are strongly affected by their different Ni content. Among these, the 3D Ni_0.31Co_0.69S₂/GH composite has the highest specific capacitance of 1166 F/g at a current density of 1 A/g. Furthermore, a specific capacitance of 559 F/g can be still maintained at high current density of 20 A/g. After 1000 charge–discharge cycles at 5 A/g, the specific capacitance remains a high value of 755 F/g.     

A simple approach for fabrication of interconnected graphitized macroporous carbon foam with uniform mesopore walls by using hydrothermal method

Three-dimensional (3D) highly interconnected graphitized macroporous carbon foam with uniform mesopore walls has been successfully fabricated by a simple and efficient hydrothermal approach using resorcinol and formaldehyde as carbon precursors. The commercially available cheap polyurethane (PU) foam and Pluronic F127 were used as a sacrificial polymer and mesoporous structure-directing templates, respectively. The graphitic structure of carbon foam was obtained by catalytic graphitization method using iron as catalyst. Three different carbon foams such as graphitized macro-mesoporous carbon (GMMC) foam, amorphous macro-mesoporous carbon (AMMC) foam and graphitized macroporous carbon (GMC) foam were fabricated and their physicochemical and mechanical properties were systematically measured and compared. It was found that GMMC possess well interconnected macroporous structure with uniform mesopores located in the macroporous skeletal walls of continuous framework. Besides, GMMC foam possesses a well-defined graphitic framework with high surface area (445 m²/g), high pore volume (0.35 cm³/g), uniform mesopores (3.87 nm), high open porosity (90%), low density (0.30 g/cm³) with good mechanical strength (1.25 MPa) and high electrical conductivity (11 S/cm) which makes it a promising material for many potential applications.     

Alkali catalyzed liquefaction of corncob in supercritical ethanol–water

Corncob liquefaction in supercritical ethanol–water was performed with and without the addition of an alkali catalyst by direct addition or biomass impregnation in a 250-cm³ batch reactor. The effects of temperature, solvent and alkali addition on the biomass conversion level and oil yield were investigated to find the optimum condition. For non-catalytic liquefaction using a 1:1 (v/v) ethanol: water ratio, a maximum oil yield and conversion level of 49.0% and 93.4%, respectively, were obtained at 340 °C. For alkali catalytic liquefaction, the oil yield with KOH addition (57.5%) was higher than that from KOH-impregnated corncob liquefaction (43.3%). The oil from liquefaction with KOH addition had higher heating value (26.7–35.3 MJ kg⁻¹) than the corncob (19.1 MJ kg⁻¹). The dominant components of the obtained oil were found by GC/MS analysis to be aldehyde, ester, phenol derivatives and aromatic compounds.     

Photocatalytic evolution of hydrogen over mesoporous TiO2 supported NiO photocatalyst prepared by single-step sol–gel process with surfactant template

Photocatalytic activity of mesoporous titania supported nickel oxide photocatalyst synthesized by single-step sol–gel (SSSG) process combined with surfactant-assisted template method was investigated for hydrogen evolution from an aqueous methanol solution, in comparison with one prepared by conventional incipient wetness impregnation (IWI) method. In single-step sol–gel process, nickel precursor was introduced into the titania sol prepared with the aid of a surfactant template behaving as pore-controlling agent to attain meso-scaled pore. The single-step sol–gel photocatalyst was experimentally found to enhance the photocatalytic evolution of hydrogen rather than the impregnated one. The optimum level of nickel loading in photocatalytic activity test for single-step sol–gel method was slightly higher than that for incipient wetness impregnation method. Characterization results demonstrated the significant modification of physical characteristics of the single-step sol–gel photocatalyst, anticipated to relating to the observation of higher photocatalytic hydrogen evolution activity.     

Microwave Demulsification in Removing Naphthenic Acids from Diesel Oil

Emulsification is an undesired phenomenon in the refining of highly acidic oil by alkali-washing electro-refining. In this article, a novel microwave method is applied for demulsification in the removing of naphthenic acid from diesel oil. The internal heating is attributed to molecular rotation and ionic conduction. The decrease of interface zeta-potential and the viscosity of diesel oil are responsible for the demulsification with microwave irradiation. The results exhibited that the demulsification rate is maximized when the optimum microwave irradiation power, exposure time, and irradiation pressure for Anshan and Liaohe diesel oil are deemed to be 375 W, 5/6 min and 0.05 MPa, respectively.     

高效广谱微生物复合破乳剂的制备及其应用

为解决破乳剂的选择性强、破乳效率低的问题,采用化学破乳剂和微生物破乳剂复合的方法,研制出了广谱、高效、低成本的破乳剂,并用大庆三次采油采出液、塔河原油、南阳原油、蓬莱原油、俄罗斯混合原油进行了脱水、脱盐评价。结果表明:对于大庆油田采出液,微生物复合与化学破乳剂比较,脱水效率提高5%以上,脱出水含油可降低40%以上;对于易乳化的南阳原油、蓬莱原油,脱后含盐可达3 mg/L以下,脱出水含油可降低50%以上。工业应用表明:对于俄罗斯混合原油脱后含盐可达2 mg/L以下,脱出水含油可降低70%以上,脱后排水含油小于15 mg/L。所研制的微生物复合破乳剂适应性强,成本可降低20%~50%。     

1D helical ZnII metal–organic polymers: Syntheses,structures and fluorescent properties

Hydrothermal reactions of 1,1′-(1,5-pentanediyl)bis-1H-benzimidazole (pbbm) with ZnCl₂ afford two 1D helical metal–organic polymers {[ZnCl₂(pbbm)] · (H₂O)_1/8}_n (1) and {[Zn(pbbm)₂] · Cl₂ · (H₂O)_1/2}_n (2). Polymer 1 features a 1D single helical architecture, whereas 2 possesses a 1D cationic double helical chain framework. Photoluminescence investigations reveal that both of them display strong emissions in the solid state at room temperature, which could originate from a ligand-to-ligand charge-transfer (LLCT) transition, as confirmed by the molecular orbital (MO) calculations.     

Synthesis and swelling properties of poly[acrylamide-co-(crotonic acid)] superabsorbents

Superabsorbent polymers of acrylamide (AAm)/crotonic acid (CA) were synthesized by foamed polymerization in an aqueous solution of AAm with CA as a comonomer, initiated by an initiator couple of ammonium persulfate and N,N,N′N′-tetramethylethylenediamine. A crosslinking agent N,N′-methylenebisacrylamide, a foaming agent sodium bicarbonate, and a foam stabilizer, a triblock copolymer of polyoxyethylene/polyoxypropylene/polyoxyethylene, were used in the polymerization. The influences of the relative contents of CA, crosslinking agent, and initiator, on the swelling properties of the superabsorbent polymer systems were examined. The superabsorbent polymer synthesized with an AAm/CA ratio of 98:2 by mole, 0.5 wt.% of N,N′-methylenebisacrylamide and 1 wt.% of ammonium persulfate at 250 rpm and 50 °C for 30 min of polymerization time produced the highest water absorption of 211 ± 9 times its dried weight and could absorb water up to 162 ± 4 g g⁻¹ of the dry copolymer within 10 min. The electrochemical reaction for acrylamide–crotonic acid polymerization was investigated by cyclic voltammetry. The anodic current indicated that acrylamide acting as an electron donor whereas crotonic acid performed as an electron receiver, then providing the cathodic current. The diffusion of water into the superabsorbent polymer was non-Fickian (case II and anomalous). Acrylamide–crotonic acid superabsorbents containing various crosslinker concentrations had a water swelling in the range of 79–289 g g⁻¹. The diffusion coefficients varied between 6.9 × 10⁻⁹ and 5.1 × 10⁻⁸ cm² s⁻¹. Adsorption of the basic dye by the superabsorbent was a monolayer evaluated by the Langmuir isotherm. The superabsorbents can thus be used to adsorb cationic dyes in textile industry.     

Ionic liquid modified graphene oxide for enhanced flame retardancy and mechanical properties of epoxy resin

In this work, to improve its dispersion and flame retardancy, graphene oxide (GO) was functionalized by silane coupling agent KH550 and 1-butyl-3-methylimidazole hexafluorophosphate (PF₆-ILs), and characteristics of the PF₆-ILs@GO was obtained by transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Then, the synergistic flame retardant of GO or PF₆-ILs@GO and melamine pyrophosphate (MPP) were applied for epoxy resin (EP) materials. Specifically, the limiting oxygen index (LOI) value of EP with 0.1 wt% PF₆-ILs@GO was increased to 29.2% from 27.5% of EP/MPP composites, and the UL-94 test reached the V-0 rating. The CCT results showed that the total heat release (THR) and total smoke release (TSP) of EP/MPP/PF₆-ILs@GO composites were significantly 24.4% and 53.4% lower than that of EP/MPP composites. Besides, the thermal behavior investigated by TGA indicated that the char-forming effect of GO and PF₆-ILs@GO was great, the residual char of EP/MPP/PF₆-ILs@GO composites was as high as 19.5% at 700°C, and its thermal stability was higher than that of EP/MPP composites. On the other hand, the tensile strength of EP/MPP/GO and EP/MPP/PF₆-ILs@GO composites were increased by 15.6% and 28.3% compared with EP/MPP composites. According to SEM analysis, the EP/MPP/GO composites formed a good protective char layer, which can effectively improve flame retardancy of EP. This research represents a new method of flame retardant modified GO to improve the flame retardancy and mechanical properties of polymers.     

Study on improvement of conductivity of Cu-Cr-Zr alloys

The influence of alloying, heat treatment, and plastic working on the performance of Cu-Cr-Zr alloys was investigated. The precipitated phases were characterized as Cr, Cu51Zr14 and Cu5Zr. Cu-Cr-Zr alloys demonstrate combination properties of high strength and high conductivity after solution treatment, aging treatment, and plastic deformation. Precipitation course of Cr is the main factor that influences the conductivity of Cu-Cr-Zr alloys, while adding Zr in the alloys adjusts the orientation relationship between Cr and matrix, and tends to increase the conductivity of aged Cu-Cr-Zr alloys after deformation.