Prediction of rock mass P wave velocity using blasthole drilling information

In this paper, the development of the models for the prediction of rock mass P wave velocity is presented. For model development, the database of 53 cases including widely used and recorded drilling parameters and P wave velocity was constructed from the field studies conducted in 13 open pit lignite mines. Both conventional linear, non-linear multiple regression and Adaptive Neuro Fuzzy Inference System (ANFIS) were used for model development. Prediction performance indicators showed that ANFIS model presented the best performance and it can successfully be used for the preliminary prediction of P wave velocities of rock masses.     

浅析HPT250轧机中滑移系数对轧制过程的影响

通过HPT250轧机在技术改造中遇到的一个问题，即滑移系数对冷轧元缝钢管在轧制过程中所起的作用。在实际生产中经过不断的技术研究和改进。使闲置多年的HPT250轧机为钢管公司的生产迭拉起到很大的作用。     

几种酚类抗氧剂在润滑油中的应用

采用旋转氧弹法、高压差示扫描量热法等方法研究了5种酚类抗氧剂对6种润滑油基础油氧化安定性的改善效果。结果表明:向加氢基础油中加入0.25%(质量分数)抗氧剂2246-S和RHY510(含硫酚类抗氧剂),可使HVIWH125,HVIWH150,HVIWH500,KN4006,KN40105种润滑油基础油的诱导期由27～88min提高到226～397min;使HVIWH125,HVIWH150,HVIWH300,HVIWH500,KN4006,KN40106种润滑油基础油的起始氧化温度由193.34～198.90℃提高到205.48～230.27℃。     

旋转导向钻井偏心稳定器横向振动研究

旋转导向钻井偏心稳定器横向振动研究是国家863“可控(闭环)三维轨迹钻井技术”课题研究的部分内容。选取偏心稳定器的心轴作为研究对象,以偏心稳定器心轴连续梁系统的横向振动模型受力分析为基础,根据课题研究中所设计的心轴结构形式,建立了与实际情况较为接近的三铰支点的连续梁系统横向振动方程;并分析了偏心稳定器横向振动对钻井工具和钻具系统的影响,为合理进行心轴设计以及偏心稳定器样机在现场的正确使用和钻井参数的合理选择,提供了科学的理论依据和实用的计算方法。计算实例表明,当钻压范围选择在80~250kN时,215.9mm井眼钻进中的确存在19~20、61~63、162~163r/min前三阶横向共振转速区间,因此在选择钻井参数时应通过钻压与转速的配合,尽可能避开横向共振转速,以保证下部钻具组合系统及作业安全。     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

钛精矿回转窑直接还原过程结圈可能性的探讨

通过煤种，入窑球冷态强度和还原过程强度，以及钛精矿与煤灰混合物的软化温度等分析探讨了钛精矿预热球团回转窑直接还原产生结圈的可能性，获得了可以避免结圈的结论。     

滚动转子式压缩机传热模拟

就滚动转子式压缩机的传热特性进行了分析。把压缩机分为15块，视摩擦损失和电机发热为内热源，考虑润滑油流动在传热过程中的影响，应用集中参数法对每块进行了能量分析，建立了传热数学模型并进行了计算。     

混联法氧化铝生产中熟料窑节能降耗的研究

通过对熟料窑的热工综合测试，分析了熟料窑的能耗组成和影响能耗的关键因素，总结了技术改造带来的经济效益和生产中存在的问题，提出了进一步挖潜降耗的措施。     

Prediction of axial velocity profiles and solids hold-up in a rotary kiln

Axial bed depth profiles were experimentally measured in a rotary kiln containing ilmenite particles under steady state and transient conditions. The variables include feed rate of solids, inclination and rotational speed of the kiln. and dam height. The variation of the axial velocity with kiln axis was estimated. The semi-experimental model proposed by Perron and Bui (1990) was modified to include the effect of the variables of the present study. The mean residence time of solids was estimated from the fractional hold-up and expressed in terms of the process variables. The transients induced by a step change in any of the operating conditions were measured as variation of discharge rate of solids with time.     

天津钢管公司DRC直接还原厂生产工艺与自动控制

天津钢管公司DRC直接还原厂将采用英国戴维国际工程公司的DRC煤基直接还原技术,以铁矿石、煤、石灰石为原燃料,用回转窑来生产直接还原铁(DRI)。该厂将由两条回转窑生产线组成,每条生产线的生产能力为15万tDRI/年,回转窑规格为φ5.0m×80m。工厂生产主线将采用计算机集散控制系统(DCS)以实现对生产过程的自动控制。