Designed damping controller for SSSC to improve stability of a hybrid offshore wind farms considering time delay

This paper presents the stability improvement results of hybrid doubly fed induction generator (DFIG)-based and permanent magnet generator (PMG)-based offshore wind farms (OWFs) using a static synchronous series compensator (SSSC). An adaptive-network-based fuzzy inference system (ANFIS) controller of the proposed SSSC is designed to render adequate damping characteristics to the studied system. A frequency-domain approach based on a linearized system model using eigenvalue technique analysis is performed. A time-domain scheme based on a nonlinear system model subject to a three-phase short circuit fault at infinite bus with variations in the signal transmission delays has also been investigated to compare the damping of the studied system in cases of with and without controller. The simulation results with MATLAB/SIMULINK toolbox have been presented. It can be concluded from the simulation results that the proposed SSSC joined with the designed ANFIS damping controller can offer adequate damping performance to the studied hybrid DFIG-based and PMG-based OWFs under severe disturbance.     

Hetero-assembly of colloidal particles in concentrated non-aqueous suspensions by polymer dispersant design

Although many colloidal assembling systems have been reported, most systems suffer from severe aggregation under high solid concentrations, which can often be observed in typical hetero-aggregation system. In this study, we created a hetero-assembly system using concentrated (~50 vol%) suspensions by mixing large SiO₂ particles modified with polyacrylic acid partially complexed with oleylamine (PAA-OAm) and small SiO₂ particles modified with polyethyleneimine partially complexed with oleic acid (PEI-OA) in a non-aqueous solvent. We demonstrated that hetero-assembly is driven by the interactions between the uncomplexed carboxyl/amine groups of the PAA/PEI present on the particles, while severe aggregation is simultaneously prevented by the steric repulsions of the aliphatic oleyl chains. Comparison of the cross sections of the in-situ solidified hetero-assembled suspensions with those of ideally assembled structures which were reproduced by a simulation considering the statistical distribution of particles strongly supported successful particle assembling via the proposed approach. The results revealed that the OA content in the PEI-OA complex was the dominant factor that controlled the dispersion and assembling state of the binary particles. The significance of this study is that our findings will provide a class of colloidal dispersion state which binary particles were assembled in a high solid content suspension without forming strong aggregates.     

Relationship between the adhesion properties of UV-curable alumina suspensions and the functionalities and structures of UV-curable acrylate monomers for DLP-based ceramic stereolithography

Digital light processing (DLP)-based ceramic stereolithography has attracted significant attentions due to the high printing speed and high dimensional accuracy of DLP printers. However, undesired dropping of unfinished ceramic parts during printing, owing to inadequate adhesion between the first cured layer and the substrate of the building platform, still remains a challenge. In this study, the relationship between the adhesion properties of ultraviolet (UV)-curable alumina (α-Al₂O₃) suspensions and the functionalities and structures of UV-curable acrylate monomers was investigated. With an increase in the proportions of monofunctional monomers, the adhesion abilities of UV-curable alumina suspensions enhanced because of reduced volume shrinkage, however, inferior curing performances were observed due to a decrease in the double bond densities. Furthermore, the large-volume branched chain structures in monofunctional monomers and ethyoxyl groups in polyfunctional monomers effectively decreased the volume contraction, improving the adhesion performances of UV-curable alumina suspensions and facilitating the conversion of double bonds to provide excellent curing properties, further guaranteeing strong adhesion of these suspensions to the substrate.     

Robust Control of Permanent Magnet Synchronous Motors

In this paper, permanent magnet synchronous motors (PMSMs) are investigated. According to the feature of PMSMs, a novel state equation of PMSMs is obtained by choosing suitable state variables. Based on the state equation, robust controllers are designed via interval matrix and PI control idea. In terms of bilinear matrix inequations, sufficient conditions for the existence of the robust controller are derived. In order to reduce the conservation and the dependence on parameter, the control inputs of PMSMs are divided into two parts, a feedforward control input and a feedback control input, and relevant sufficient conditions for the existence of the controller are obtained. Because of the suitable choice of state variables, the proposed control strategies can cope with the load uncertainty and have robustness for disturbance. Finally, simulations are carried out via Matlab/Simulink soft to verify the effectiveness of the proposed control strategies. The performance of the proposed control strategies are demonstrated by the simulation results.      

忠武输气管道悬索跨越设计创新及探讨

忠武输气管道有4次悬索跨越,分别是蚂蝗溪悬索跨越、木龙河悬索跨越、马水河悬索跨越、野三河悬索跨越。文章介绍了这几座悬索跨越管桥设计中采用的多项新技术,如采用热聚乙烯半平行钢丝索代替以往的钢丝绳;采用钢管塔架代替以往的角钢塔架;根据地形地貌特点变换风索型式或取消塔架等。这些新技术、新设计在工程中均取得了良好的效果。另外,文章还针对悬索跨越桥面结构型式、预拱度设置、不对称荷载的影响、风索基础的设置等问题进行了探讨。     

厚膜永磁阵列微致动器的磁路研究

研究了厚膜永磁阵列微致动器中的磁场分布，并研究了永磁阵列单元几何尺寸对微致动器电磁力的影响。结果表明，厚膜永磁阵列单元高宽比和磁体单元间隔对微致动器电磁力影响较大磁徕单元高宽比为0．7是一个比较合适的尺寸。     

Low Temperature Physics at the Laboratoire National des Champs Magnétiques Pulsés in Toulouse

An overview over past and present activities and future developments at the Toulouse pulsed magnetic field facility is given, both as far as technical developments of the infrastructure, as well as low temperature physics performed at the LNCMP are concerned.     

船闸直立墙基坑开挖与锚固施工程序

三峡船闸深槽开挖与锚固工程量大，工期紧，施工强度高，施工难度大。因此，合理的施工程序有利于边坡稳定和施工，是快速和高质量施工的关键。分析了永久船闸直立墙基坑开挖与锚固施工程序的复杂性和进行研究的必要性。介绍了设计阶段研究船闸开挖与锚固的施工程序。对施工过程中研究施工程序时考虑的因素，研究的主要内容以及实际采用的施工程序作了简要的分析，归纳和总结。     

重介选煤厂自动化控制系统

介绍了重介选煤厂实现全自动控制的系统原理及所能实现的各项功能。