基于滚动摩擦作用下玉米颗粒在模拟筒仓卸料中的力链分析（网络首发、推荐阅读）

针对颗粒滚动摩擦作用对筒仓中玉米颗粒的力链空间分布进行研究，通过EDEM离散元软件建立筒仓模型与仿真玉米颗粒模型进行卸粮仿真模拟，并与筒仓卸料实验作流态对比，验证模型与仿真结果的准确性。通过对模拟仓进行切片观察和数据处理，对比分析了不同摩擦情况下力链的细观参数随时间演化规律。模拟结果表明：颗粒间摩擦系数越大，卸粮完成的最终时间越长；颗粒间滚动摩擦系数越小，颗粒由整体流转变为管状流的时间越早。对于有漏斗的筒仓来说，减小颗粒间摩擦会改变整体流和管状流之间的极限，从而增加产生管状流的面积。标准滚动摩擦系数下玉米颗粒在卸料过程中会出现起拱-塌陷效应；减小滚动摩擦，玉米颗粒卸料较稳定，未出现起拱的应力突增、以及拱塌陷的应力衰减；增大颗粒间滚动摩擦不但会增加拱效应，且出现成拱高度距离漏斗口更高。     

磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

新型地锚张弦梁式泥石流格栅坝构件受力的简化计算方法

针对常见泥石流防治结构被冲击破坏的问题，基于“柔性消能”理念，结合张弦梁结构和竖向预应力锚杆技术，提出一种既能改善结构受力性能、增加结构整体抗冲击能力、保证结构安全可靠，又能减小结构构件截面尺寸、节约成本、便于现场施工组装和后期运营维护的新型地锚张弦梁式泥石流格栅坝，并阐述其技术原理。根据泥石流荷载分布和新型地锚张弦梁式泥石流格栅坝的受力特征，给出其简化的内力计算方法；并利用SAP2000建立新结构有限元模型，分析了结构的整体受力，验证了构件简化计算方法的合理性；结合Python语言和Qt De? signer软件开发了相应的设计计算软件，对新型地锚张弦梁式泥石流格栅坝的内力进行求解。结果表明：提出的新结构抗冲击性能好，构件受力均匀；以后设计中应关注竖杆的剪切脆性破坏和立柱偏心受力情况，保证结构安全；变形协调仅使底层张弦梁与竖杆内力偏大，实际工程应用时，应着重验算底层构件，防止其破坏；文中提出的简化计算方法能较准确的反映结构的受力特性，具有一定的合理性，研究可为新型地锚张弦梁式泥石流格栅坝的设计计算和推广应用提供理论依据和技术支持。     

Estimation of gradient size of interfacial strain and its optimization for effective magnetoelectric coupling in (CoFe2O4) – (0.93Na0.5Bi0.5TiO3 – 0.07BaTiO3), 2-2 nano-composites

Strain-mediated coupling between the magnetic and electrically ordered phases plays a significant role in magnetoelectric (ME) nano-composites. This study explores a method to analyse and quantify interfacial strain using a grazing angle scan (α) in a ME composite optimised for a specific microstructure. The details of strain around the interface CoFe₂O₄ (CFO) – 0.93Na_0.5Bi_0.5TiO₃ – 0.07BaTiO₃ (NBT-BT) was determined by performing ‘α’ scan, in order to gather information at various depths of the NBT-BT layer around maximum intensity (110) reflection. The strain around the interface was observed to dominate over a spatial region of ～20–30 nm away from the interface. The Piezoresponse force microscopy (PFM) studies performed near the interface reveal that the strain constrain experienced by the ferroelectric layer operates such that polarisation rotation and domain wall motion are constrained compared to the strain relaxed region of the film. For effective strain transfer, heterostructures grown with optimised thicknesses (～20–30 nm) exhibited a superior inverse piezomagnetic effect.     

梁结构振动支承约束反力控制

支承或连接构件对梁结构的动力学性能有至关重要影响,必须保证其在振动过程中不发生破坏或者失效。通过合理设计和布局附加弹性支承可以实现对这些重要连接构件所承受约束反力的控制。应用微分变换法推导含附加支承的梁结构支承约束反力及其对于附加支承位置和刚度的灵敏度表达式,并通过优化设计附加支承位置和刚度实现具有弹性约束端的简支梁结构各支承约束反力的平衡,可提高结构的动力学性能。     

折臂式随车起重机转台的拓扑优化设计

为了使折臂式随车起重机转台在最大应力不超过材料许用应力的前提下实现轻量化设计的目的,通过ADAMS软件仿真确定其极限工况,对转台进行静力学分析及拓扑优化。通过拓扑优化得到了理想的材料分布。基于优化结果调整转台结构,并对改进后的转台进行静力学分析。结果表明,优化后的转台能够满足实际的使用需求。同时,转台质量降低了12%,证明了优化设计的有效性和可行性,并为折臂式随车起重机的相关设计提供了一定的借鉴。     

Upscaled DEM-CFD model for vibrated fluidized bed based on particle-scale similarities

Simulation based on discrete element method (DEM) coupled with computational fluid dynamics (CFD), coupled DEM-CFD, is a powerful tool for investigating the details of dense particle–fluid interaction problems such as in fluidized beds and pneumatic conveyers. The addition of a mechanical vibration to a system can drastically alter the particle and fluid flows; however, their detailed mechanisms are not well understood. In this study, a DEM-CFD model based on a non-inertial frame of reference is developed to achieve a better understanding of the influence of vibration in a vibrated fluidized bed. Because the high computational cost of DEM-CFD calculations is still a major problem, an upscaled coarse-graining model is also employed. To realize similar behaviors with enlarged model particles, non-dimensional parameters at the particle scale were deduced from the governing equations. The suitability and limitations of the proposed model were examined for a density segregation problem of a binary system. To reduce the computational costs, we show that the ratio between the bed width and model particle size can be reduced to a minimum value of 100; to obtain similar segregation behaviors, the ratio between the bed height and model particle size is considered unchanged.     

表面活性剂对低渗透油藏渗吸的影响

采用不同类型的表面活性剂进行自发渗吸实验,并对表面活性剂改善岩石润湿性、降低界面张力的能力进行了分析。实验结果表明,阴离子型表面活性剂改善润湿性的能力好于其他类型的表面活性剂,且在岩心中的自发渗吸效果最好,这是由于阴离子型表面活性剂改善润湿性的机理为离子对形成机理,强于阳离子的吸附机理;接触角是决定渗吸能否发生的决定性因素,只有接触角小于70°时渗吸才能发生;界面张力影响渗吸速度和最终采出程度,对于渗透率为1 mD的岩心,最佳界面张力为10~(-1) mN/m。     

Nonlinear dynamic behaviors and control based on simulation of high-purity heat integrated air separation column

In this paper, the dynamic behaviors on the basis of simulation for high-purity heat integrated air separation column (HIASC) are studied. A nonlinear generic model control (GMC) scheme is proposed based on the nonlinear behavior analyses of a HIASC process, and an adaptive generic model control (AGMC) scheme is further presented to correct the model parameters online. Related internal model control (IMC) scheme and multi-loop PID (M-PID) scheme are also developed as the comparative base. The comparative researches are carried out among these linear and nonlinear control schemes in detail. The simulation research results show that the proposed AGMC schemes present advantages in both servo control and regulatory control for the high-purity HIASC.     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.