Experimental study on the propagation characteristics of hydrogen/methane/air premixed flames in a narrow channel

This work is focused on the explosion characteristics of premixed gas containing different volume fractions of hydrogen in a narrow channel (1000 mm × 50 mm × 10 mm) under the circumstance of stoichiometric ratio. The ignition positions were set in the closed end and the middle of the pipeline respectively. The results showed that when the gas was ignited at the pipeline closed end, the propagating flame was tulip structure for different premixed gas. When the hydrogen volume fraction was less than 40%, the flame propagation speed increased significantly with the rise of hydrogen volume fraction, and the overpressure peak also appeared obviously in advance. However, when the volume fraction of hydrogen was more than 40%, the increase of flame propagation speed and the overpressure peak occurrence time varied slightly. Furthermore, when the ignition position was placed in the middle of the pipeline, the flame propagation speed propagating to the opening end was much faster than that propagating to the closing end, and there was no tulip shape when the flame propagates to the opening end. The flame propagating to the closed end appeared tulip shape under the influence of airflow, and high-frequency flame oscillation occurred during the propagation. This work shows that the hydrogen volume fraction and ignition position significantly affected the flame structure, flame front speed, and explosion overpressure.     

Synergistic Effects of Polybenzimidazole and Aramide on Enhancing Flame-Retardancy and Solubility

Aromatic and functional polymers with processibility derived from biobased starting materials are prerequisite considering sustainable society. Poly(2,5-benzimidazole)s are rigid-rod polymers to show ultrahigh thermal stability such as flame retardance, while usually suffer from poor solubility. Here, poly(benzimidazole-co-amide)s are synthesized from two biobased monomers, 3,4-diaminobenzoic acid and a semirigid comonomer, 4-aminohydrocinnamic acid. The copolymers with an amide composition of 80 mol% and higher are soluble in widely used polar solvents to fabricate the films keeping high flame retardance, which is comparable with popular high-performance polymers such as aromatic polyimides, polyetheretherketone, polyphenylene sulfide, etc.     

低分子量聚丙烯酸钾的合成及其应用

采用水溶液聚合法制备了低分子量聚丙烯酸钾（PAAK），并作为新型消焰剂加入单基发射药中。通过火焰原子吸收光谱法测试了PAAK中钾的含量；用乌氏黏度计测定了特性黏度；采用DSC法研究不同pH值的PAAK与硝化棉（NC）的相容性；利用充氮氧弹法对添加PAAK、硝酸钾KNO₃、硫酸钾K₂SO₄的单基发射药的燃烧残渣进行了对比研究。结果表明，合成的PAAK中，钾的质量分数为15.21%，相对分子量在3 000左右，有利于和NC均匀混合，且在中性或微碱性（pH＝7.0~7.5）的情况与NC相容性良好。与传统的KNO₃、K₂SO₄消焰剂相比，PAAK能够和NC均匀混合，制备均质透明的单基发射药；PAAK发射药的燃烧残渣最少，占发射药质量的0.18%。     

总变差模型在书画打印宣纸印刷质量预测中的应用

为了建立适用于书画打印宣纸印刷质量的预测模型,本研究测量了14种书画打印宣纸的粗糙度、白度、不透明度、定量、光泽度和针对宣纸特别设定的帘纹深浅以及帘纹疏密度等表面物理参量,并在相同条件下,使用喷墨打印设备输出并测量印品色度值,利用总变差模型构建去除帘纹色差的测定方法,得到与人眼视觉特征相符的色差。运用GRNN广义回归神经网络结合书画打印宣纸表面物理参量与宣纸去帘纹后的色差值,建立预测模型。结果表明,该模型能够在仅测量书画打印宣纸表面物理参量的情况下,便能较为准确地预测书画打印宣纸印刷质量,为书画打印宣纸印刷前的选纸工作提供指导依据。     

Reduction of chlorophenols and sludge management from paper industry wastewater using electrocoagulation process

ABSTRACT

In this study, electrocoagulation (EC) was used to determine the optimum conditions on the basis of maximum chemical oxygen demand (COD) and color removal. At the optimum conditions chlorophenols (CPs), biological oxygen demand and total organic carbon (TOC) were determined. The biodegradability of wastewater was increased significantly with 63% COD, 98% color, 61% TOC and overall 65.51% reductions in CPs. Further, the electro-coagulated sludge was characterized by using different analytical techniques to assist the physicochemical and elemental phases, to find-out better management option, reusability for plant growth and safe disposal. Additionally, aluminum content (70.62%) was successfully recovered from sludge.     

Characterization of a plasma polymer coating from an organophosphorus silane deposited at atmospheric pressure for fire-retardant purposes

Protective coatings from diethylphosphatoethyltriethoxysilane (DEPETS) have been deposited on different polymer substrates in a plasma discharge operated at atmospheric pressure. Plasma polymer chemistry and structure were characterized by means of Fourier transform infrared spectroscopy (FTIR), laser desorption ionization-mass spectrometry (LDI-MS), nuclear magnetic resonance (NMR) and scanning electron microscopy (SEM). A chemical structure of the plasma polymer has been proposed based on the coating molecular characterization. Coatings were deposited on polycarbonate (PC) and polyamide 6 (PA6) substrates. The flame retardant properties of coated substrate samples were assessed using cone calorimetry and compared to those of bare substrates. A significant increase in the time to ignition (TTI), up to +143%, was recorded after coating deposition due to the formation of a high-performance barrier layer at the surface of both polymer substrates.     

Flame characteristics of premixed H2-air mixtures explosion venting in a spherical container through a duct

The explosion venting duct can effectively reduce the hazard degree of a gas explosion and conduct the venting energy to the safe area. To investigate the flame quantitative propagation law of explosion venting with a duct, the effects of hydrogen fraction and explosion venting duct length on jet flame propagation characteristics of premixed H₂-air mixtures were analyzed through experiment and simulation. The experiment results under initial conditions of room temperature and 1 atm show that when hydrogen fraction was high enough, part of the unburned hydrogen was mixed with air again to reach an ignitable concentration, resulting in the secondary combustion was easier produced and the duration of the secondary flame increased. With the increase of venting duct length, the flame front distance and propagation velocity increased. Meanwhile, the spatial distribution of pressure field and temperature field, and the propagation process and mechanism of the flame venting with a duct were analyzed using FLUENT software. The variation of the pressure wave and the pressure reflection oscillation law in the explosion venting duct was captured. Therefore, in the industrial explosion venting design with a duct, the hazard caused by the coupling of venting pressure and venting flame under different fractions should be considered comprehensively.     

On the capacity of the state‐dependent interference relay channel

This paper considers the state‐dependent interference relay channel (SIRC) in which one of the two users may operate as a secondary user and the relay has a noncausal access to the signals from both users. For discrete memoryless SIRC, we first establish the achievable rate region by carefully merging Han‐Kobayashi rate splitting encoding technique, superposition encoding, and Gelfand‐Pinsker encoding technique. Then, based on the achievable rate region that we derive, the capacity of the SIRC is established in many different scenarios including (a) the weak interference regime, (b) the strong interference regime, and (c) the very strong interference regime. This means that our capacity results contain all available known results in the literature. Next, the achievable rate region and the associated capacity results are also evaluated in the case of additive Gaussian noise. Additionally, many numerical examples are investigated to show the value of our theoretical derivations.     

Synergistic flame retardant effects of activated carbon and molybdenum oxide in poly(vinyl chloride)

The synergistic effects of activated carbon (AC) and molybdenum oxide (MoO₃) in improving the flame retardancy of poly(vinyl chloride) (PVC) were investigated. The effects of AC, MoO₃ and their mixture with a mass ratio of 1:1 on the flame retardancy and smoke suppression properties of PVC were studied using the limiting oxygen index and cone calorimeter tests. It was found that the flame retardancy of the relatively cheaper AC was slightly weaker than that of MoO₃. In addition, the incorporation of AC and MoO₃ greatly reduced the total heat release and improved smoke suppressant property of PVC composites. When the total content of AC and MoO₃ was 10 phr, PVC/AC/MoO₃ had the lowest peak heat release rate and peak smoke production rate values of 173.80 kW m^?2 and 0.1472 m² s^?1, which represented reductions of 47.3 and 59.9%, respectively, compared with those of PVC. Furthermore, thermogravimetric analysis and gel content tests were used to analyze the flame retardant mechanism of AC and MoO₃, with results showing that AC could promote early crosslinking in PVC. Char residue left after heating at 500 °C was analyzed using scanning electron microscopy and Raman spectroscopy, and the results showed that MoO₃ produced the most compact char, with the smallest and most organized carbonaceous microstructures. © 2017 Society of Chemical Industry