Investigation of stress fields for non-standard sized glass plates loaded by ring-on-ring

A ring-on-ring (ROR) test is a prevailing test method for evaluating the equi-biaxial strength of glass materials. However, current ROR test standards limit the strength and size of glass to prevent a nonlinear behavior. In this study, the feasibility of ROR testing for non-standard, high-strength glass, such as tempered or ion-exchanged rectangular glass is investigated. To this end, ROR simulation based on theory and experiment is conducted for thirty non-standard glasses with widths of 100–300 mm and aspect ratios of 1.0–2.0. As a result, the maximum measurable stress was about 215.6 MPa for 100 × 200 mm glass and 481.3 MPa for 300 × 600 mm glass with a 3% deviation, which is well above the strength of regular tempered glass. The main purpose of this work is to understand the range of aspect ratio of horizontal and vertical widths of a glass plate that can be evaluated by the standard ROR test.     

大口径光学元件装夹转运结构设计及分析

为了实现大口径光学元件的安全装夹、转运,通过光学元件开槽与不开槽两种装夹方式的分析,得出开槽夹紧转运方式将带来微裂纹、应力集中、成本高等缺陷,提出了利用摩擦力克服光学零件的重力和惯性力的低应力装夹转运方案。通过对光学元件低应力夹紧结构设计,并利用有限元分析方法,得到不开槽装夹方式下,光学元件的最大主应力为1.11 MPa,最大切应力为0.73 MPa,远低于光学元件破坏的强度极限,且受力均匀,无应力集中现象。     

Flame characteristics of premixed H2-air mixtures explosion venting in a spherical container through a duct

The explosion venting duct can effectively reduce the hazard degree of a gas explosion and conduct the venting energy to the safe area. To investigate the flame quantitative propagation law of explosion venting with a duct, the effects of hydrogen fraction and explosion venting duct length on jet flame propagation characteristics of premixed H₂-air mixtures were analyzed through experiment and simulation. The experiment results under initial conditions of room temperature and 1 atm show that when hydrogen fraction was high enough, part of the unburned hydrogen was mixed with air again to reach an ignitable concentration, resulting in the secondary combustion was easier produced and the duration of the secondary flame increased. With the increase of venting duct length, the flame front distance and propagation velocity increased. Meanwhile, the spatial distribution of pressure field and temperature field, and the propagation process and mechanism of the flame venting with a duct were analyzed using FLUENT software. The variation of the pressure wave and the pressure reflection oscillation law in the explosion venting duct was captured. Therefore, in the industrial explosion venting design with a duct, the hazard caused by the coupling of venting pressure and venting flame under different fractions should be considered comprehensively.     

基于新型光纤的传输技术探讨

随着互联网的高速发展，引发了网络流量、电信骨干网流量急速增长，使得网络容量的提升迫在眉睫。目前，100G 系统已经商用，超100G系统能够更有效地解决流量和网络带宽持续增长带来的压力，本文主要介绍新型单模光纤的特性以及探讨基于新型单模光纤的传输技术。     

Deposition of UF5 on the surface of steel material having oxide coating in contact with gaseous UF6

When UF6 is handled in leak tight system, the amount of uranium compound formed on the surface of containers, valves, and others in UF6 handling facilities is not so significant for a short term that special attention has not been given to this problem. The present work was done to throw some more light on this problem based on the recent experiment. We discuss the possibility that the intermolecular transfer of a fluorine atom from UF6 to UF5 may participate in the formation of uranium compound. The discussion includes also the unique features contained in the experimental result, the reaction processes assumed in this problem, and the derivation of a rate equation for expressing the deposition of uranium compound. Furthermore, we propose a new method for determining nonlinear parameters included in a governing differential equation having two variables for expressing the deposition of uranium compound from experimental raw data.     

Development and validation of a micro-fin tubes evaporator model using R134a and R1234yf as working fluids

This paper presents a model of shell and tube evaporator with micro-fin tubes using R1234yf and R134a. The model developed for this evaporator uses the ε-NTU method to predict the evaporating pressure, the refrigerant outlet enthalpy and the outlet temperature of the secondary fluid. The model accuracy is evaluated using different two-phase flow boiling correlations for micro-fin tubes and comparing predicted and experimental data. The experimental tests were carried out for a wide range of operating conditions using R134a and R1234yf as working fluids. The predicted parameter with maximum deviations, between the predicted and experimental data, is the evaporating pressure. The correlation of Akhavan– Behabadi et al. was used to predict flow boiling heat transfer, with an error on cooling capacity prediction below 5%. Simulations, carried out with this validated model, show that the overall heat transfer coefficient of R1234yf has a maximum decrease of 10% compared with R134a.     

A self‐scalable load injection service

Load testing of applications is an important and costly activity for software provider companies. Classical solutions are very difficult to set up statically, and their cost is prohibitive in terms of both human and hardware resources. Virtualized cloud computing platforms provide new opportunities for stressing an application's scalability, by providing a large range of flexible and less expensive (pay‐per‐use model) computation units. On the basis of these advantages, load testing solutions could be provided on demand in the cloud. This paper describes a Benchmark‐as‐a‐Service solution that automatically scales the load injection platform and facilitates its setup according to load profiles. Our approach is based on: (i) virtualization of the benchmarking platform to create self‐scaling injectors; (ii) online calibration to characterize the injector's capacity and impact on the benched application; and (iii) a provisioning solution to appropriately scale the load injection platform ahead of time. We also report experiments on a benchmark illustrating the benefits of this system in terms of cost and resource reductions. Copyright © 2013 John Wiley & Sons, Ltd.     

Experimental and numerical analysis of the influence of cable tray arrangements on the resulting mass loss rate and fire spreading

In the context of industrial buildings and power plants, electrical installations and cable trays represent a main fuel load and a potential initial fire source due to possible short circuits or comparable malfunction. Furthermore, a fire can spread from one tray to additional trays mounted above and/or horizontally on one tray. Because of the high significance of cable fires, several research projects have been carried out, investigating the fire behaviour of cables from small‐scale tests, eg, the cone calorimeter, up to large‐scale tests, analysing complete cable tray constructions. The goal of the work presented in this paper is the extension of the knowledge regarding the influence of geometrical parameters like the packing density and tray distance on the burning behaviour and fire spread of cable tray installations. The results are considered, together with test results from the literature, to quantify the main physical parameters describing the burning behaviour. In a next step, the general applicability of these parameters as input data for the parametrization of the source term of numerical simulations is shown. The test results show that the burning behaviour and the fire spreading highly depend on the cable arrangement of the cables on the cable tray, in combination with other boundary conditions. By applying the results as input for a fire simulation, the mass loss rate is considered appropriately.