Performance of surface ionic conduction single chamber fuel cell prepared by the sol gel method

The performance of surface ionic conduction single chamber fuel cell (SIC‐SCFC) prepared by the sol gel method was studied on electric characteristics due to the differences of the operating temperature and humidity, the electrode distance and electrolyte film depth, and multiple cells with the series and parallel connections. The SIC–SCFC was arranged the both anode of Pt and cathode of Au on the boehmite electrolyte. The open circuit voltage (OCV) of single cell achieved a maximum of 530mV in the dry gas mixtures of O₂/H₂=50% in room temperature operation, and but it became decrease as over 60%. The OCV was maintained the constant value between operating temperatures of 30°C to 80°C, and but it was decreased sharply at over 90°C because a humidity on the cell became lower as increasing operating temperature. Then, the cell property was improved to 120°C by adding to the humidity of 70% using a humidifier. The electrode distance and the electrolyte film depth of SIC‐SCFC found to be contributed to the reductions of the cell resistance and the surface roughness on the electrode, respectively. Moreover, the power property of SIC‐SCFC was significantly improved by cell stacks comprised of the series or parallel connection of a cell.     

Study on the relationship between the particle size distribution and the effectiveness of the K‐powder fire extinguishing agent

The relationship between the particle size distribution and the extinguishing effectiveness of the new K‐powder fire extinguishing agent has been studied experimentally, to explore the reason of the great extinguishing efficiency exhibited by the new K‐powder fire extinguishing agent on Class B fire (liquid fuel fire). The results of the experiment showed that the extinguishing effectiveness increased along with the decrease of the particle size distribution. In addition, a sharp discontinuity appeared around the limiting size, about 40 μm. The powder with the particle size below 40 μm exhibited highly effective extinguishing with the minimum effective extinguishing concentration C_xr = 23 g·m^?3, while the powder with the particle size above 40 μm exhibited little fire extinguishing efficiency. Compared with other fire extinguishing agents produced by different substances, the new K‐powder fire extinguishing has the bigger limiting size. That means, in the same particle size distribution, the new K‐powder fire extinguishing agent contains more highly effective powder than others contain, and is more effective.     

大直径平底负压容器优化设计

通过对大直径平底负压容器平底板的设计计算,平底板计算厚度很厚。通过分析,提出了对平底板采取加强措施,从而减薄平底板计算厚度的方法。该容器在实际生产过程中性能可靠、稳定,对类似设备设计具有借鉴意义。     

Reducing treatment zone diameter in orthokeratology and its effect on peripheral ocular refraction

PurposeTo determine whether orthokeratology (OK) induced treatment zone (TZ) diameter can be reduced by altering OK lens design, and if so the impact of modifying TZ diameter on relative peripheral refraction (RPR).Methods16 subjects (mean age 23.4 ± 1.5 years; 8 female) completed the study. Standard (Control) OK lens design (PJ, Capricornia, Australia) or a modified version (Test) where the back optic zone diameter was reduced, and back optic zone asphericity and intermediate lens curves were altered, were worn overnight only for 7-nights in a randomised double masked order, with a minimum 1-week wash out (no lens wear) between lens designs. Full correction of refractive error was targeted. Refraction; best corrected visual acuity (BCVA); RPR (Shin-Nippon NVision-k 5001) along the horizontal and vertical meridians; and corneal topography (Medmont E300) were measured before starting lens wear and in the morning after lens removal after the seventh night of lens wear for both lens designs. TZ diameter and decentration was calculated from corneal topography.ResultsAfter 7-nights of wear both lens designs created -2.00D refraction effect with no significant difference in refractive effect or change to BCVA between the designs. The Test design created a significantly smaller horizontal (4.78 ± 0.37 vs 5.70 ± 0.37 mm, p < 0.001) and vertical (5.09 ± 0.51 vs 5.92 ± 0.51 mm p < 0.001) TZ diameter. The TZ was decentered inferior temporal with no significant difference between designs. There was no significant difference between the lens designs in RPR along the horizontal and vertical meridians at any measurement period.ConclusionsOK induced TZ diameter can be reliably reduced by altering OK lens design without detrimentally effecting lens centration or refractive effect. Reducing TZ diameter did not alter RPR, though measurement artifacts could be responsible for masking an effect. Longitudinal studies are needed to assess whether smaller TZ OK lens designs increase efficacy for slowing progression of myopia.     

浅析火力发电厂汽水系统中内径管与外径管的设计选择

按照管道加工工艺的不同,管道可分为内径控制管和外径控制管。通过热轧工艺生产的外径控制无缝钢管,可满足火力发电厂汽水系统中绝大部分管道的使用要求。对于超(超)临界机组的主蒸汽和高温再热蒸汽管道采用的P91/P92材质的大口径厚壁无缝钢管,由于对材料性能和加工工艺有特殊要求,因此宜采用内径控制管。     

石化装置蒸汽发生系统的仪表工程设计

主要探讨了某石化装置蒸汽发生系统的仪表工程设计，提出了复杂控制方案、联锁方案设计，同时也详述了影响系统设计的因素，如测量补偿和迁移等。     

一种估算单桩经济直径的方法

在滩海油田开发过程中,经常需要设立立管桩,在环境荷载的作用下,立管桩顶部会发生位移,较大的位移对立管及栈桥的安全很不利,因此需要合理确定单桩的直径。埕岛油田在确定单桩直径时引入了经济直径的概念,文章对经济直径的原理进行了分析,给出了桩顶位移和桩径经济指数计算公式,并举例进行了计算,得出了桩径与桩顶位移及桩径经济指数的关系曲线, 进而求得经济桩径的取值范围。文章还对该方法的优缺点进行了分析。     

水锤涌浪联合试验的变态模型相似律

该文详细推导了在同一个物理模型中同时模拟调压室涌浪和压力钢管中的水锤时应满足的变态模型相似律，结果应用于电站模型试验中。     

井下液气分离器分离原理及结构改进

液气分离器就是充分利用电泵机组的高转速、气体和液体之间悬殊的密度差异进行液气离心分离。经过多年的发展,在传统的液气分离器结构基础上又出现了许多新的设计和改进,大大提高了液气分离器的分离效果。文章重点论述了液气分离器的分离原理和结构上的改进之处。     

Efficient Parallel Algorithms for Some Graph Theory Problems

In this paper,a sequential algorithm computing the aww vertex pair distance matrix D and the path matrix Pis given.On a PRAM EREW model with p,1≤p≤n^2,processors,a parallel version of the sequential algorithm is shown.This method can also be used to get a parallel algorithm to compute transitive closure array A^* of an undirected graph.The time complexity of the parallel algorithm is O(n^3/p).If D,P and A^* are known,it is shown that the problems to find all connected components,to compute the diameter of an undirected graph,to determine the center of a directed graph and to search for a directed cycle with the minimum(maximum)length in a directed graph can all be solved in O(n^2/p logp)time.