Numerical approach to analyze fluid flow in a type C tank for liquefied hydrogen carrier (part 1: Sloshing flow)

The demand for clean energy use has been increasing worldwide, and hydrogen has attracted attention as an alternative energy source. The efficient transport of hydrogen must be established such that hydrogen may be used as an energy source. In this study, we considered the influences of various parameters in the transportation of liquefied hydrogen using type C tanks in shipping vessels. The sloshing and thermal flows were considered in the transportation of liquefied hydrogen, which exists as a cryogenic liquid at ?253 °C. In this study, the sloshing flow was analyzed using a numerical approach. A multiphase sloshing simulation was performed using the volume of fluid method for the observation and analysis of the internal flow. First, a sloshing experiment according to the gas-liquid density ratio performed by other researchers was utilized to verify the simulation technique and investigate the characteristics of liquefied hydrogen. Based on the results of this experiment, a sloshing simulation was then performed for a type C cargo tank for liquefied hydrogen carriers under three different filling level conditions. The sloshing impact pressure inside of the tank was measured via simulation and subjected to statistical analysis. In addition, the influence of sloshing flow on the appendages installed inside of the type C tank (stiffened ring and swash bulkhead) was quantitatively evaluated. In particular, the influence of the sloshing flow inside of the type C tank on the appendages can be utilized as an important indicator at the design stage. Furthermore, if such sloshing impact forces are repeatedly experienced over an extended period of time under cryogenic conditions, the behavior of the tank and appendages must be analyzed in terms of fatigue and brittle failure to ensure the safety of the transportation operation.     

基于误差估值累加开环校正的诱导式欺骗检测方法

诱导式卫星欺骗干扰可诱导航空器逐渐偏离预定航迹，难以被发现，因此及时有效地检测干扰是飞行安全的保障。在现有紧组合导航体制基础上，设计了一种基于误差估值累加开环校正的紧组合导航结构，并证明了其性能与传统闭环校正紧组合导航性能等效。在此结构中，将紧组合导航系统与自适应序贯概率比检测方法结合，提出了一种基于误差估值累加开环校正的诱导式欺骗检测方法，融合紧组合导航信息与其他不受欺骗影响的导航信息，构建欺骗检测统计量进行诱导式欺骗检测。仿真结果表明，开环校正结构可避免随时间累加的惯性导航系统误差所导致的组合导航滤波器发散问题，同时欺骗检测方法可进一步提高算法对“最坏”情形下微小诱导式欺骗的检测效果。     

An adaptive sliding mode observer based near-optimal OER tracking control approach for PEMFC under dynamic operation condition

Tracking control of oxygen excess ratio (OER) is crucial for dynamic performance and operating efficiency of the proton exchange membrane fuel cell (PEMFC). OER tracking errors and overshoots under dynamic load limit the PEMFC output power performance, and also could lead oxygen starvation which seriously affect the life of PEMFC. To solve this problem, an adaptive sliding mode observer based near-optimal OER tracking control approach is proposed in this paper. According to real time load demand, a dynamic OER optimization strategy is designed to obtain an optimal OER. A nonlinear system model based near-optimal controller is designed to minimize the OER tracking error under variable operation condition of PEMFC. An adaptive sliding mode observer is utilized to estimate the uncertain parameters of the PEMFC air supply system and update parameters in near-optimal controller. The proposed control approach is implemented in OER tracking experiments based on air supply system of a 5 kW PEMFC test platform. The experiment results are analyzed and demonstrate the efficacy of the proposed control approach under load changes, external disturbances and parameter uncertainties of PEFMC system.     

Estimating long-term time-resolved indoor PM2.5 of outdoor and indoor origin using easily obtainable inputs

To evaluate the separate impacts on human health and establish effective control strategies, it is crucial to estimate the contribution of outdoor infiltration and indoor emission to indoor PM_2.5 in buildings. This study used an algorithm to automatically estimate the long-term time-resolved indoor PM_2.5 of outdoor and indoor origin in real apartments with natural ventilation. The inputs for the algorithm were only the time-resolved indoor/outdoor PM_2.5 concentrations and occupants’ window actions, which were easily obtained from the low-cost sensors. This study first applied the algorithm in an apartment in Tianjin, China. The indoor/outdoor contribution to the gross indoor exposure and time-resolved infiltration factor were automatically estimated using the algorithm. The influence of outdoor PM_2.5 data source and algorithm parameters on the estimated results was analyzed. The algorithm was then applied in four other apartments located in Chongqing, Shenyang, Xi'an, and Urumqi to further demonstrate its feasibility. The results provided indirect evidence, such as the plausible explanations for seasonal and spatial variation, to partially support the success of the algorithm used in real apartments. Through the analysis, this study also identified several further development directions to facilitate the practical applications of the algorithm, such as robust long-term outdoor PM_2.5 monitoring using low-cost light-scattering sensors.     

工业园区混合能源优化配置方法应用与实践

为了充分挖掘多能源之间的互补潜力,使工业园区混合能源系统的配置方式由传统粗放式转变为精确优化配置并降低系统配置方案的保守性,基于粒子群联合CPLEX求解算法对工业园区的系统配置和运行调度方案进行分析优化,并以某生物园区为例进行了实例分析,得到了目标函数下的最优设计方案和运行策略。仿真分析结果表明,优化配置方法的应用能够协调冷热电多种能源的混合利用,提升系统的综合经济性。同时,为工业园区能源供应项目的规划、设计提供参考性支撑,丰富设计手段。     

Effect of Reynolds number and boundary layer thickness on the performance of V-cone flowmeter using CFD

The effect of Reynolds number and boundary layer thickness on the performance of V-cone flowmeter has been evaluated using computational fluid dynamics (CFD). The shear stress transport k-ω (SST k-ω) turbulence model has been adopted for closure. The performance of two V-cone flowmeters with different beta ratios (β) viz., 0.6 and 0.7 for a fixed vertex angle (ϕ) of 60° has been analysed as a function of Reynolds number (Re). The results show that the coefficient of discharge (C_d) increases with Reynolds number in the laminar and transition flow regimes whereas it is nearly constant in turbulent flow regime. From the results, it can be concluded that C_d is independent of Re for values equal to 4000 and beyond. Further, it is also seen that the performance of the V-cone flowmeter is not affected by the upstream boundary layer thickness if the velocity profiles having different boundary layer thickness are extracted from an axial distance of 10D and more are fed at 5D upstream of the meter. However, the meter is sensitive to the extracted velocity profile from an axial distance of 5D and uniform velocity profile being fed at 5D upstream. The value of C_d may be sensitive as a result of the pressure variation due to the obstruction.     

Adaptive GLR-, Rao- and Wald-based CFAR detectors for a subspace signal embedded in structured Gaussian interference

The problem of detecting a subspace signal embedded in subspace Gaussian interference and thermal noise is studied in this paper. In this problem, both the signal-independent and signal-dependent interferences are assumed to be present, therefore the overall interference subspace covers the signal subspace. The approach of this paper extends previous works involving either of those two kinds of interferences. A set of secondary data containing only interference plus noise is employed to estimate the interference covariance matrix and the noise power. Three new detectors are designed via the generalized likelihood ratio (GLR), Rao and Wald tests, respectively. Their probabilities of false alarms (PFAs) and detections are analytically derived. The PFAs show that the new detectors have the constant false alarm rate (CFAR) property against the interference and noise. Numerical results show that the new detectors outperform their counterparts for the studied problem. Furthermore, the new detectors are less sensitive to the secondary data size and to the mismatched subspace signal than some other detectors, such as the GLR detector (GLRD), the adaptive matched filter (AMF), the adaptive subspace detector (ASD), etc.     

少量有机碳对单级自养脱氮工艺性能的影响

采用序批式生物膜反应器(SBBR),经过4个阶段的培养,快速富集好氧氨氧化细菌(AOB)和厌氧氨氧化细菌(AnAOB),并考察不同低碳氮比对工艺脱氮性能的影响。结果表明,NH4^+-N去除率可达到99%以上,TN去除率可达到90%以上。对应C/N=0、1和2时,反应器出水NH4^+-N和TN去除率分别为99.59%、99.5%、98.47%和93.75%、97.22%、98.11%。说明少量COD的存在,可实现同步硝化-厌氧氨氧化-反硝化,且在一定程度上提高脱氮效率。     

干湿联合冷却塔冷却节水分析软件开发及应用

为实现对干湿联合冷却塔冷却特性、节水特性的综合分析，编制干湿联合冷却塔校核计算流程，基于Visual Studio开发平台，本文开发了干湿联合冷却塔冷却节水特性分析优化软件。通过对某在运干湿联合冷却塔进行冷却节水特性计算，验证了所开发软件计算结果的准确性；在消雾节水计算结果基础上，对标干湿联合消雾冷却塔验收测试规程，生成其成雾频率曲线、耗水量曲线、塔雾指数、冷却特性曲线，综合分析其消雾特性、节水特性及冷却特性，从而确定了干湿联合冷却塔的最佳运行工况。同时运用所开发软件对比分析了某冷却塔设计干段散热面积对其消雾特性、节水特性及冷却特性的耦合影响，并分析了百叶窗开度对干湿联合冷却塔性能的影响，为干湿联合冷却塔的运行优化和设计优化提供了工具性软件支持。     

剂油比对煤焦油沥青质加氢过程的影响

以中低温煤焦油沥青质为原料,采用NiMoW/γ-Al_2O_3商业催化剂,在反应温度380℃、反应压力8 MPa和反应时间1.5 h条件下,分别在不同剂油质量比(1∶25、1∶20、1∶15、1∶10)条件下进行加氢实验,通过采用元素分析、FT-IR、XRD、~1H-NMR和XPS等分析表征手段,考察不同剂油质量比对中低温煤焦油沥青质加氢转化过程的影响。结果表明,随着剂油质量比的增加,沥青质转化率提高,加氢产物分布也发生大幅变化,沥青质和芳香分轻质化转化为饱和分。但随着剂油质量比的进一步提高,同时也发生了更多的裂化反应和缩合反应,剂油质量比在合适范围能够很好地起到加氢轻质化且抑制结焦的效果。