空压机润滑油系统可靠性试验研究

对空压机润滑系统进行分析,提出了一种润滑油压力调节机构,保证了空压机在高油温时油压正常,为空压机运动件提供充分润滑,从而提高空压机运行的可靠性。实验证明了该机构是可靠的,为空压机润滑系统设计提供了参考依据。     

磷酸高效分解磷矿实验研究

为改进湿法磷酸生产工艺,提高副产石膏的品质,减少湿法磷酸固体副产物磷石膏堆存产生的经济和环保压力,进行了磷酸分解磷矿制磷酸的实验研究。采用贵州某磷矿为主要原料,研究了湿法磷酸预分解磷矿的反应条件。通过单因素实验确定了湿法磷酸分解磷矿最优反应条件：反应温度为75 ℃,磷酸与磷矿的质量比（液固比）为9,反应时间为3 h,磷酸质量分数为30%（以五氧化二磷计）。在此条件下,磷矿的分解率为98.62%。     

核电厂立式泵电机多故障耦合振动问题的处理

某核电厂立式水泵配套电机存在两径向方向振动差异大、启机后振动缓慢上升的振动现象，为解决该问题，本文利用频谱分析、固有频率分析、相位分析等方法进行故障诊断，判断出该配套电机存在结构共振、转子热弯曲、动不平衡的耦合问题，并最终通过调整螺栓及现场动平衡方法成功解决了振动问题。      

海工磨细矿渣混凝土的冻渗性与孔结构研究

在天然海水侵蚀和冻融循环作用下,与普通混凝土对比,对掺加磨细矿渣(GGBS)海工混凝土的抗冻性和抗氯离子渗透性的耦合性能(简称冻渗性)以及孔结构的细观性能进行了研究.用R值代表混凝土冻渗性指标进行分析讨论,结果表明:掺加磨细矿渣的混凝土,无论掺加引气剂与否,水胶比增大,R值逐渐减小;不掺引气剂,矿粉掺量增大,R值减小;掺加引气剂,矿粉掺量增大,R值增大;引气剂掺量增大,R值增大,但引气剂掺量超过一定极限,R值增长不明显;抗压强度等级在40～60 MPa范围内,其强度值与R值没有明显的规律性.MIP结果表明:掺加矿粉和引气剂的海工混凝土经过冻渗后,无害孔和少害孔的数量较多;R值与最可几孔径大小有明显的反比关系.     

三维姿态监测技术在地震测井中的应用

在地震测井施工中,为监测地下检波器的运动特征,需应用三维监测技术。首先从映射几何的角度深入分析OpenGL的三维监测技术,建立OpenGL虚拟场景,然后分析检波器模型内外方位元素的表达,利用三维绘图技术建立检波器的立体模型,最后对所获取的坐标数据进行快速的三维绘图技术处理,形成实时可靠的立体模拟界面。实验结果表明:检波器的方位角模拟精确度能保证在1°以内,满足后期简化数据处理的要求。该技术应用在地震测井中时,具有远程、可靠、无损检测等特点,为操作人员提供直观可靠的观测决策平台,并且结合实际需求能够扩展多种功能模块,可广泛应用于测井过程中方位数据的获取。     

郭沫若的翻译理论与思想探析

从探讨郭沫若的生平背景入手,介绍了他的翻译成就,并对郭沫若的翻译理论和翻译思想做出了初步的剖析。郭沫若的翻译实践主要可以从郭沫若译著《英诗译稿》和《浮士德》窥见一斑,而郭沫若的翻译理论则可从罗新璋所著的《翻译论集》和方克平所著的《溯洄从美:从批判理论到文学翻译》中探出精髓。对郭沫若翻译实践和理论的研究可以发现郭沫若的"创作论"的地位固然不可撼动,但其中对于创作的维度却并没有提出很好的标准。     

Combination of heat treatment and chitosan coating to improve postharvest quality of wolfberry (Lycium barbarum)

The synergistic application of hot water dip at 42 °C for 30 min and 1% chitosan coating on differentiation in postharvest quality traits, microstructure as well as microbiological evolution of wolfberry fruits was investigated. Fresh wolfberry fruits were stored at 2 ± 0.5 °C and 90% relative humidity (RH) for 28 days. Results indicated the combination of prestorage heat treatment and chitosan coating maintained higher levels of ascorbic acid, total phenolic contents and antioxidant capacity as well as lower decay, compared with untreated wolfberry fruits. The possible mechanism was that the heat treatment almost sealed open stomata to limit the sites of pathogen penetration into fruits independently, followed by the biofilm formed by chitosan which controlled secondary infections as well as slowed changes in fruit respiration and metabolic activity in wolfberries. The synergistically treated fruit also exhibited a higher acceptability obtained by sensory analysis after cold storage. In this sense, the integrated application of heat treatment and chitosan coating could be regarded as an effective strategy to extend storage life and maintain the postharvest quality of wolfberry fruits.     

某水电厂励磁系统跨接器故障分析

本文对一起机组起励时灭磁电阻严重烧坏并最终导致停机的事故进行分析,查找出灭磁电阻严重烧坏的原因.通过一系列试验,模拟机组起励停机过程,证明此次故障是由于机械跨接器在实际运行中存在缺陷造成的.最后,为防止此类事故再次发生,提出相关技术改造意见,以保证励磁系统安全稳定运行.     

Heat propagation in thermally conductive polymers of PA6 and hexagonal boron nitride

Thermally conductive polymers offer new possibilities for the heat dissipation in electric and electronic components, for example, by a three‐dimensional shaping of the heat sinks. To face safety regulations, improved fire performance of those components is required. In contrast to unfilled polymers, those materials exhibit an entirely different thermal behavior. To investigate the flammability, a phosphorus flame retardant was incorporated into thermally conductive composites of polyamide 6 and hexagonal boron nitride. The flame retardant decreased the thermal conductivity only slightly. However, the burning behavior changed significantly, due to a different heat propagation, which was investigated using a thermographic camera. An optimum content of hexagonal boron nitride for a sufficient thermal conductivity and fire performance was found between 20 and 30 vol%. The improvement of the fire performance was due to a faster heat release out of the pyrolysis zone and an earlier decomposition of the flame retardant. For higher contents of hexagonal boron nitride, the heat was spread faster within the part, promoting an earlier ignition and increasing the decomposition rate of the flame retardant.     

脉冲高度权重技术测量197Au中子俘获截面

脉冲高度权重技术是利用C_6D_6探测器测量中子俘获截面的一种数据处理方法。在中国散裂中子源(China Spallation Neutron Source,CSNS)的反角白光中子源(Back-n)靶站上,通过测量金靶(~(197)Au)的中子俘获截面,验证了该方法的可靠性。首先利用Geant4蒙特卡罗程序模拟给出了不同靶条件下的探测器效率,脉冲高度权重函数等基本项,使得加权后的探测器效率与γ能量成正比。然后通过实验测量了~(197)Au中子俘获截面。结果表明:测量获得的中子俘获截面数据和ENDF/B-VⅢ.0评价数据相符合,同时发现随着实验靶尺寸的不同和质子束功率的增加,会使得实验本底的扣除误差越来越大。