A 250-Mb/s/pin, 1-Gb double-data-rate SDRAM with a bidirectionaldelay and an interbank shared redundancy scheme

This paper describes three circuit technologies indispensable for high-bandwidth multibank DRAM's. (1) A clock generator based on a bidirectional delay (BDD) eliminates the output skew. The BDD measures the cycle time as the quantity charged or discharged of an analog quantity, and replicates it in the next cycle. This achieves a 0.18-mm ², two-cycle-lock clock generator operating from 25 to 167 MHz with a 30-ps resolution. (2) A quad-coupled receiver eliminates the internal skew caused by the difference between a rise input and a fall input by 40%. (3) An interbank shared redundancy scheme (ISR) with a variable unit redundancy (VUR) efficiently increases yield in multibank DRAM's. The ISR allows redundancy match circuits to be shared with two or more banks. The VUR allows the number of units replaced to be variable. These circuit technologies achieved a 250-Mb/s/pin, 8-bank, 1-Gb double-data-rate synchronous DRAM     

An ISDN Subscriber Loop Transmission System Based on Echo Cancellation Technique

This paper proposes an ISDN subscriber loop transmission system based on an echo cancellation technique which fully supports the CCITT recommended basic interface for ISDN, i.e.,B + B + Dover metallic cables. System design considerations of cable loss, crosstalk, impulsive noise, and system requirements such as power feeding on a caLl-by-call basis are discussed, and a transmission system is proposed. The proposed system is characterized by the use of a new line code, named "modified biphase code." The use of this code with fixed line loss equalization and coherent detection achieves circuit simplification. A special adaptation algorithm is incorporated with the echo canceller that significantly reduces convergence time. Experimental results show satisfactory performance with respect to the residual echo and the bit error rate. Since the system requires only a simple nonadaptive circuit for analog portion, it is suitable for LSI implementation.     

Phase diagram and Raman spectroscopy of EuCl2---NaCl binary mixtures

A phase diagram of the EuCl₂---NaCl system was determined by differential scanning calorimetry (DSC) and the activity coefficients of EuCl₂ and NaCl in this system were estimated under some assumptions. According to DSC measurement, it was found that there were two phase transitions at 1123.9 K and 1016.8 K. In order to specify the melting point of EuCl₂ we did Raman spectroscopy experiments. Thus, the melting point of EuCl₂ was evaluated to be 1016.8 K which was detected as the lower peak in the DSC curve. Raman spectroscopy of this system suggested that complex species were not formed clearly in the EuCl₂ poor system and the estimated activity coefficients of EuCl₂ also supported this suggestion.     

Highly Stable Au Nanoparticles with Tunable Spacing and Their Potential Application in Surface Plasmon Resonance Biosensors

Colloidal Au‐amplified surface plasmon resonance (SPR), like traditional SPR, is typically used to detect binding events on a thin noble metal film. The two major concerns in developing colloidal Au‐amplified SPR lie in 1) the instability, manifested as a change in morphology following immersion in organic solvents and aqueous solutions, and 2) the uncontrollable interparticle distance, determining probe spacing and inducing steric hindrance between neighboring probe molecules. This may introduce uncertainties into such detecting techniques, degrade the sensitivity, and become the barricade hampering colloidal Au‐based transducers from applications in sensing. In this paper, colloidal Au‐amplified SPR transducers are produced by using ultrathin Au/Al₂O₃ nanocomposite films via a radio frequency magnetron co‐sputtering method. Deposited Au/Al₂O₃ nanocomposite films exhibit superior stability, and average interparticle distances between Au nanoparticles with similar average sizes can be tuned by changing surface coverage. These characteristics are ascribed to the spacer function and rim confinement of dielectric Al₂O₃ and highlight their advantages for application in optimal nanoparticle‐amplified SPR, especially when the probe size is smaller than the target molecule size. This importance is demonstrated here for the binding of protein (streptavidin) targets to the probe (biotin) surface. In this case, the dielectric matrix Al₂O₃ is a main contributor, behaving as a spacer, tuning the concentration of Au nanoparticles, and manipulating the average interparticle distance, and thus guaranteeing an appropriate number of biotin molecules and expected near‐field coupling to obtain optimal sensing performance.     

Wall slip and melt-fracture of polystyrene melts in capillary flow

We investigated slip and unstable flow phenomena of polystyrene melts in capillaries from the view of the effects of temperature and molecular weight by using three polystyrene samples with different molecular weights (M_w = 192,000, M_w = 258,000, and M_w = 321,000). The slip velocities are estimated by the Mooney method and the modified Mooney method. We found that the slip velocity increases and the critical slip stress above which a slip starts to occur decreases with the temperature. We also observed the melt-fracture at above a critical melt-fracture stress higher than . We found that the onset of melt fracture is affected by the extensional stress near the entry region to the capillary in the barrel and the melt-fracture tends to easily occur with increase of the molecular weight, but is not sensitive to the temperature.     

Novel transdermal drug delivery system with polyhydroxyalkanoate and starburst polyamidoamine dendrimer

In search of an efficient transdermal drug delivery system (TDDS), a polyhydroxyalkanoate (PHA)-based system with a polyamidoamine dendrimer was examined. Tamsulosin was used as the model drug. The dendrimer was found to act as the weak enhancer. By adding the dendrimer, the dendrimer-containing PHA matrix achieved the clinically required amount of tamsulosin permeating through the skin model. This is also the first report of the application of PHA and dendrimer to the TDDS.     

A circulating current control scheme for multiple three‐level NPC inverter systems

In recent years, motor drive systems for steel rolling mills have been steadily increasing in capacity. In particular, the development of three‐level NPC (Neutral Point Clamped) inverters is now focusing on the replacement of cycloconverters. In order to satisfy such a requirement, in this paper a multiple three‐level NPC inverter system is proposed. The configuration consists of two three‐level NPC inverters with the same configuration connected in parallel by current limiting reactors. In this case, the circulating current flowing between the two three‐level NPC inverters must be controlled to prevent a decrease in the maximum output capacity. In particular, a new method for control of the circulating current is a major topic of discussion. The method is based on space voltage vector‐based PWM (Pulse Width Modulation) control for the three‐level NPC inverters and the circulating current is controlled by adjusting the output durations of the respective space voltage vectors. In this method the circulating current controller can be decoupled from the motor current controller. Therefore, it is possible to design the different controllers independently. In addition, the experimental results obtained using an induction motor show that the circulating current can be reduced to within 2% of the rated motor current when the motor current response exceeds 1000 rad/s. © 2001 Scripta Technica, Electr Eng Jpn, 136(2): 38–48, 2001     

Study of shunt type SFCL equipped with electromagnetic repulsion switch for large capacity

Using a high‐temperature superconductor, we constructed and tested a model Superconducting Fault Current Limiter (SFCL). The SFCL that we proposed has a vacuum interrupter with electromagnetic repulsion mechanism. We set out to construct a high‐voltage‐class SFCL. We produced an electromagnetic repulsion switch equipped with a 24‐kV vacuum interrupter (VI). However, the opening speed becomes slower, because the larger vacuum interrupter needs a heavier‐weight contact. For this reason, the current which flows in a superconductor may not be interruptible within a half cycle of current. In order to solve this problem, it is necessary to change the design of the coil connected in parallel and to strengthen the electromagnetic repulsion force at the time of opening the vacuum interrupter. Thus, the design of the coil was changed, and in order to examine whether the problem is solvable, a current limiting test was conducted. We carried out a current limiting test using second‐generation (2G) HTS wire. The element used in this experiment has a stainless steel stabilizer on both sides of the wire. In the experiment we succeeded in interrupting the current of a superconductor within a half cycle. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 173(4): 20–27, 2010; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21039     

Improvement of Stainless Steel Making Operation Adapting Instable Raw Material Price

Sumikin Iron and Steel Corporation (SISC) is the main manufacturing base of seamless tube materials in Sumitomo Metals group, and stainless steel making plant is in charge of semi‐manufactured special steel products such as stainless and high alloy steel. Total manufacturing costs of these special steels are heavily dependent on the price of raw material. Therefore, reduction of its usage and optimizing operation process in order to absorb influence of its unstable price are important issues. In this report, we introduce three cases as following: yield improvement in order to reduce raw material usage, optimization of the steel dust usage, and active use of low‐price raw material through dividing refining process.     

Development of a Simplified Calculation Tool for Voltage Drop Caused by Transformer Inrush in Distribution System

It is well known that a voltage drop due to inrush current at an energizing transformer may at times interrupt electrical equipment. Generally, the voltage drop is calculated by using a sophisticated tool such as EMTP, so that the transformer saturation phenomenon has been properly represented. However, it is not practical for distribution system engineers to calculate the voltage drop with transformer inrush by using EMTP, because there are many network access requests needing such calculations with many kinds of transformers. Therefore, in this paper, a simplified and easy‐to‐use calculation tool for voltage drops caused by transformer inrush in a distribution system is developed. In order to understand the voltage drop by inrush current during the planning stage, it is formulated by considering the transformer saturation/unsaturation periods in each winding type. The newly developed tool is based on versatile spreadsheet software such as Microsoft Excel ýO.R. It can be used with accuracy similar to that of EMTP. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 185(1): 36–47, 2013; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22394