Modeling risk based maintenance using fuzzy analytic network process

The study deals with the problem of maintenance policy selection for an industrial unit. Maintenance policy selection is a multiple criteria decision making problem. Criteria considered here are ‘risk of equipment failure’ and the ‘cost of maintenance’. The maintenance policies considered are Corrective Maintenance (CM), Time Based Maintenance (TBM), Condition Based Maintenance (CBM) and Shutdown Maintenance (SM). For modeling, fuzzy analytic network process (FANP) has been employed. Chang’s extended analysis has been applied to deal with the fuzzy variables and the preferred maintenance policy alternative is found out using FANP analysis. The methodology was applied to a unit of a chemical plant and the suitable maintenance policy was found out for each of the 13 equipment of the unit. The results were compared to the earlier study using Analytic Hierarchal Process and Goal Programming (Arunraj and Maiti, 2010) vis-a-vis the existing practices. The results show that CBM is preferred when the risk possessed by an equipment is very high while CM is preferred in those cases where risk is low and cost is the main consideration. But in cases where both cost and risk are somewhat equally important, TBM is the preferred option.     

On Testing Prebond Dies with Incomplete Clock Networks in a 3D IC Using DLLs

3D integration of ICs is an emerging technology where multiple silicon dies are stacked vertically. The manufacturing itself is based on wafer-to-wafer bonding, die-to-wafer bonding or die-to-die bonding. Wafer-to-wafer bonding has the lowest yield as a good die may be stacked against a bad die, resulting in a wasted good die. Thus the latter two options are preferred to keep yield high and manufacturing costs low. However, these methods require dies to be tested separately before they are stacked. A problem with testing dies separately is that the clock network of a prebond die may be incomplete before stacking. In this paper we present a solution to address this problem. The solution is based on on-die Delay Lock Loop (DLL) implementations that are only activated during testing prebond unstacked dies to synchronize disconnected clock regions. A problem with using DLLs in testing is that they cannot be turned on or off within a single cycle. Since scan-based testing requires that test patterns be scanned in at a slow clock frequency before fast capture clocks are applied, On-Product Clock Generation (OPCG) must be used. The proposed solution addresses the above problems and allows a prebond with an incomplete clock network to be tested with low skew.     

Contraction Twinning Dominated Tensile Deformation and Subsequent Fracture in Extruded Mg-1Mn (Wt Pct) at Ambient Temperature

Metallurgical and Materials Transactions A - Due to their excellent strength-to-weight ratio, Mg alloys are attractive for applications where weight savings are critical. However, the limited cold...     

Topology Management Ensuring Reliability in Delay Sensitive Sensor Networks with Arbitrary Node Failures

The lifetime of a sensor network is influenced by the efficient utilization of the resource constrained sensor nodes. The tree-based data gathering offers good quality of service (QoS) for the running applications. However, data gathering at the sink reduces the network lifetime due to a fast failure of highly loaded nodes. Loss of connectivity and sensing coverage affect the performance of the applications that demand critical QoS. In this paper, a data gathering tree management scheme has been proposed to deal with arbitrary node failures in delay-sensitive sensor networks. A load-balanced distributed BFS tree construction procedure has been introduced for an efficient data gathering. Based on the initial tree construction, a tree maintenance scheme and an application message handler have been designed to ensure the reliable delivery of the application messages. The correctness of the proposed scheme has been verified both theoretically and with the help of simulation. The proposed scheme offers low overhead, enhanced network lifetime and good QoS in terms of delay and reliability of the application messages.     

Analysis of Fatty Acid and Lignan Composition of Indian Germplasm of Sesame to Evaluate Their Nutritional Merits

An attempt was made to individually analyze a germplasm collection of 54 indigenous Indian sesame cultivars for fatty acid and lignan composition of their seed oil by gas chromatography and high performance liquid chromatography, respectively. The entries varied in their fatty acid and lignan composition. The mean percentage contents of palmitic, stearic, oleic, linoleic and α‐linolenic acids ranged between 10–22, 5–10, 38–50, 18–43 and less than 1 whereas sesamol, sesamin and sesamolin scored between 3–37, 27–67, 20–59 of the total percentage of lignan, respectively. The highest percentage of α‐linolenic acid (ALA) was obtained in Var‐9 (1.3 % of the total fatty acids). Among the lignans, high sesamin content is considered to be significant, particularly in terms of long shelf life and nutraceutical value of sesame seed oil. The study has broadened our understanding related to differential biochemical composition of the rich sesame germplasms, thereby providing us with a useful groundwork for identifying potential targets and suitable cultivars for genetic engineering approaches to be undertaken in order to improve the nutritional quality of sesame oil, which in turn would be beneficial towards human health.     

Poly(ethylene oxide)‐g‐gellan polysaccharide nanocarriers for controlled gastrointestinal delivery of simvastatin

Herein, a novel gellan polysaccharide‐based amphiphilic copolymer was synthesized for the development of simvastatin‐loaded micellar nanoparticles. The nanoparticles were explored for their controlled drug release and improved pharmacodynamic potentials. The copolymer was characterized by Fourier transform infrared spectroscopy (FTIR) and elemental analysis. The onset of copolymer micellization was detected by fluorescence spectroscopy. Simvastatin was loaded into micellar particles by solvent evaporation method and the particles were then characterized by microscopic and light scattering techniques. The physical state of drug was studied by X‐ray diffraction analysis. Pharmacodynamic assessment of the micellar preparations was done on rabbit models. The copolymer formed micellar nanoparticles in water. Critical micellar concentration was 9.12mg/l. The micellar particles (426.8–912.6nm) entrapped a maximum of 18.86% drug. Higher negative zeta potential indicated physical stability of micellar systems. A simple diffusion mechanism was operative in the event of comparatively faster drug release in pH6.8 phosphate buffer solution. No significant drug‐copolymer interaction was traced by FTIR spectroscopy. The amorphization of drug into micellar particles reduced LDL‐cholesterol level by ～45% in hyperlipidemic rabbits and this was about 2.5 times higher than pure drug dispersion. Copolymer micellar nanoparticles of simvastatin could control cholesterol level in hyperlipidemic rabbits and thus had potential in drug delivery applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42399.     

Effects of SEBS-g-MA copolymer on non-isothermal crystallization kinetics of polypropylene

The non-isothermal crystallization kinetics of pure PP and PP/SEBS-g-MA blends up to volume fraction, Φ _d (0–0.50) was studied by differential scanning calorimetry at four different cooling rates. Crystallization parameters were analyzed by Ozawa and Liu models. The Ozawa model fits in the PP/SEBS-g-MA blends and indicates the effect of SEBS-g-MA copolymer on the crystallization process of polypropylene. Augis–Bennet model has been used to calculate activation energy, ?E, during non-isothermal crystallization process. The value of ?E decreased with SEBS-g-MA due to flexibility of SEBS-g-MA by which movements of chains of PP become easier.     

Green fire retardant finishing and combined dyeing of proteinous wool fabric

Flame retardancy was imparted to a scoured and bleached, proteinous woollen textile by using banana pseudostem sap, an ecofriendly waste agricultural product, at different pH levels. The flame retardancy characteristics of both the control and the treated fabrics were analysed in terms of the limiting oxygen index and the vertical flammability measurement. Thermal degradation and fire retardancy mechanisms were studied using thermogravimetry, scanning electron microscopy, and energy dispersive X‐ray analysis. Moreover, the charring mechanism of both the control and the banana‐pseudostem‐sap‐treated fabrics with varying pH was analysed and reported in detail. The wool fabric was also dyed with CI Acid Blue 25 using banana pseudostem sap as well as water as the medium. The fabric dyed with the banana pseudostem sap medium at pH 5.5 showed more colour exhaustion, colour strength, and thermal stability compared with the control wool fabric. The mechanism by which superior fire retardancy and colour strength are imparted to the woollen textile by the application of banana pseudostem sap is proposed.     

Novel organic–inorganic composite material as a cation exchanger from a triterpenoidal system of dammar gum: synthesis,characterization and application

A pioneer study has been conducted to synthesize novel hydrogel starting from a non-cellulosic raw material, gum dammar-a triterpenoidal system, and then converting this hydrogel into an organic–inorganic composite zirconium-based ion exchanger. Gum dammar was cross-linked with polyacrylamide zirconium (IV) iodo-oxalate [Gd-cl-poly(AAm)-Zr (IV) iodo-oxalate] by incorporating inorganic precipitates into the polymeric mixture. The polymeric mixture was synthesized using gum dammar (Gd), acrylamide (AAm), N, N′-methylene-bis-acrylamide (MBA) and potassium persulphate (KPS). The reaction conditions for synthesis of hydrogel and ion exchanger such as time (120 min), temperature (70 °C), solvent (4 mL), concentration of monomer (12.97 × 10^?3 mol/L), initiator (1.48 × 10^?4 mol/L), cross-linker (4.22 × 10^?4 mol/L) and ratio of zirconium oxychloride (0.1 M), potassium iodate (0.1 M) and oxalic acid (0.1 M) in ratio 2:3:2 were optimized to obtain maximum ion exchange capacity (2.02 meq/g). The morphology and structure of hydrogel and ion exchanger were studied using FTIR, SEM, XRD and TGA/DTA/DTG. The SEM study was followed by energy dispersive spectroscopy for elemental analysis. The ion exchanger was quite stable in various acids and bases at low concentration but it completely dissolved in acids and bases at high concentrations. Distribution studies showed that the synthesized ion exchanger had high selectivity for Pb²⁺ ions. Thus, the polymeric-inorganic hybrid material showed integration of both inorganic and organic characteristics within the composite material.