Influence of growth conditions on the V-defects in InGaN/GaN MQWs

The influence of the growth temperature,TMIn/TEGa andⅤ/Ⅲratio on the V-defects of InGaN/GaN multi-quantum wells（MQWs） has been investigated and discussed.When the TMIn flow increases from 180 to 200 sccm,the density of V-defects increases from 2.72×10¹⁸ to 5.24×10¹⁸ cm^-2,and the V-defect width and depth increase too.The density also increases with the growth temperature.The densities are 2.05×10⁸,2.72×10¹⁸ and 4.23×10⁸ cm^-2,corresponding to a growth temperature of 748,753 and 758℃respectively.When the NH₃ flows are 5000,6600 and 8000 sccm,the densities of the V-defects of these samples are 6.34×10¹⁸,2.72×10¹⁸ and 4.13×10¹⁸ cm^-2,respectively.A properⅤ/Ⅲratio is needed to achieve step flow growth mode.We get the best quality of InGaN/GaN MQWs at a growth temperature of 753℃TMIn flow at 180 sccm,NH₃ flow at 6600 sccm,a flatter surface and less V-defects density.The depths of these V-defects are from 10 to 30 nm,and the widths are from 100 to 200 nm.In order to suppress the influence of V-defects on reverse current and electro-static discharge of LEDs,it is essential to grow thicker p-GaN to fill the V-defects.     

Improvement of the efficiency droop of GaN-LEDs using an AlGaN/GaN superlattice insertion layer

With an n-AlGaN(4 nm)/GaN(4 nm) superlattice(SL) inserted between an n-GaN and an InGaN/GaN multiquantum well active layer,the efficiency droop of GaN-based LEDs has been improved.When the injection current is lower than 100 mA,the lumen efficiency of the LED with an n-AlGaN/GaN SL is relatively small compared to that without an n-AlGaN/GaN SL.However,as the injection current increases more than 100 mA,the lumen efficiency of the LED with an n-AlGaN/GaN SL surpasses that of an LED without an n-AlGaN/GaN SL. The wall plug efficiency of an LED has the same trend as lumen efficiency.The improvement of the efficiency droop of LEDs with n-AlGaN/GaN SLs can be attributed to a decrease in electron leakage due to the enhanced current spreading ability and electron blocking effect at high current densities.The reverse current of LEDs at -5 V reverse voltage decreases from 0.2568029 to 0.0070543μA,and the electro-static discharge(ESD) pass yield of an LED at human body mode(HBM)-ESD impulses of 2000 V increases from 60%to 90%.     

插入n-AlGaN/GaN超晶格改善GaN基LED的droop效应

在GaN基LED的n-GaN和InGaN/GaN发光区之间插入n-AlGaN/GaN超晶格来改善其droop效应。注入电流低于100mA时,插入n-AlGaN/GaN超晶格的LED的流明效率低于没有插入层的LED。注入电流高于100mA时,插入n-AlGaN/GaN超晶格的LED的流明效率高于没有插入层的LED。插入n-AlGaN/GaN超晶格后,GaN基LED在-5V的反向电压下,漏电由2.568029μA减少到0.070543μA。人体模式下,插入n-AlGaN/GaN超晶格的LED在2000V的静电电压下的通过率从60%提高到了90%。LED droop效应的改善是因为n-AlGaN/GaN超晶格过滤了穿透位错并改善了电流扩展能力。     

P 型氮化镓层生长压力对InGaN/GaN基发光二极管性能的影响

The advantages of In Ga N/Ga N light emitting diodes(LEDs) with p-Ga N grown under high pressures are studied.It is shown that the high growth pressure could lead to better electronic properties of p-Ga N layers due to the eliminated compensation effect.The contact resistivity of p-Ga N layers are decreased due to the reduced donor-like defects on the p-Ga N surface.The leakage current is also reduced,which may be induced by the better filling of V-defects with p-Ga N layers grown under high pressures.The LED efficiency thus could be enhanced with high pressure grown p-Ga N layers.     

基于InP衬底的GaAsSb/InP异质结晶体管

采用金属有机化学气相沉积生长了InP/GaAs0.5Sb0.5/InP 双异质结晶体三极管(DHBT)材料,研究了材料质量对器件性能的影响.制备的器件不但具有非常好的直流特性,而且还表现出良好的微波特性,其结果与能带理论的预言一致,DHBT集电结和发射结的电流理想因子分别为1.00和1.06,击穿电压高达15V,电流放大增益截止频率超过100GHz.     

浅析化肥对现代农业发展的意义

研讨化肥对农业发展的重要作用，通过从不同方面的比较分析，论述了化肥有着有机肥料无法比拟和替代的优势，强调了化肥生产要密切适应现代农业发展的要求，积极进行结构调整和产品优化。     

住房和城乡建设部出台核查评估办法 加强城镇生活垃圾处理设施建设运行监管

近日,住房和城乡建设部出台<全国城镇生活垃圾处理信息报告、核查和评估办法>(以下简称<办法>),确定由住房和城乡建设部负责"全国城镇生活垃圾处理管理信息系统"(以下简称信息系统)平台建设,负责全国城镇生活垃圾处理项目建设和运营的信息分析、总体评估和通报工作,对各地相关工作进行指导、监督和专项督察.     

MOCVD于高温AlN模板上生长的AlGaN材料

A high temperature AlN template was grown on sapphire substrate by metalorganic chemical vapor deposition.AFM results showed that the root mean square of the surface roughness was just 0.11 nm.Optical transmission spectrum and high resolution X-ray diffraction（XRD）characterization both proved the high quality of the AlN template.The XRD（002）rocking curve full width at half maximum（FWHM）was about 53.7 arcsec and（102）FWHM was about 625 arcsec.The densities of screw threading dislocations（TDs）and edge TDs wereestimated to be - 6 × 10^6 cm^-2 and - 4.7 ×10^9 cm^-2. AlGaN of Al composition 80.2% was further grown on the AlN template. The RMS of the surface roughness was about 0.51 nm. XRD reciprocal space mapping was carried out to accurately determine the Al composition and relaxation status in the AlGaN epilayer. The XRD （002） rocking curve FWHM of the AIGaN epilayer was about 140 arcsec and （102） FWHM was about 537 arcsec. The density of screw TDs was estimated to be - 4 × 10^7 cm^-2 and that of edge TDs was - 3.3 × 10^9 cm^-2. These values all prove the high quality of the AlN template and AlGaN epilayer.     

亚麻木酚素提取与纯化的研究进展

研究表明亚麻木酚素具有抗肿瘤、抗氧化、抗骨质疏松、抗心脑血管疾病等作用,而从亚麻籽中高效的提取分离亚麻木酚素已经成为当今的研究热点.综述国内外对亚麻木酚素的检测方法、提取工艺、分离纯化工艺和开发应用等方面的研究进展,并讨论各种方法的优缺点.     

降低中间储仓式锅炉制粉电耗的探讨

因煤粉锅炉制粉系统节能节能潜力较大,根据生产数据找到钢球规格配比、钢球的装载量、载煤量和通风量几点使制粉系统电耗偏高的重要因素,通过日常运行试验和理论计算等方式,分别找到制粉系统经济运行的四个最佳参数,找出降低磨煤机电耗的操作方法,从而实现制粉系统的节能运行。