Optimum section selection procedure for horizontal axis tidal stream turbines

Stochastic behavior of renewable energy sources forces designers to optimize the energy converters for the purpose of capturing the maximum amount of available energy. The performance of horizontal axis wind and tidal turbines mainly depends on the geometrical properties such as chord and twist distributions and also the types of sections which are utilized along the blade. The purpose of presented paper is introducing a procedure which can be utilized in order to select the optimum sections for horizontal axis tidal turbines for the purpose of increasing the turbine performance. The presented procedure also can be applied for horizontal axis wind turbines. For the purpose of evaluating the performance of the proposed method, two design types (chord and twist distributions) of tidal turbines are selected as case studies. Power coefficient is considered as objective function, and three types of hydrofoils namely NACA63-8xx, NACA44xx, and RISO-A1-xx are selected as candidate solutions. A blade element momentum theory model is used for calculating the power coefficient. The discrete ant colony optimization algorithm is selected as optimization tool. The results indicate that the utilization of the proposed method will considerably decrease the required process time for obtaining the optimum sections across the blade span, and also it is shown that using different types of sections across the blade span can increase the power coefficient of the turbine. The importance of the proposed method will be significant when various types of hydrofoils and airfoils can be considered as candidate sections across the blade span.

     

Efficiency evaluation of the photocatalytic degradation of zinc oxide nanoparticles immobilized on modified zeolites in the removal of styrene vapor from air

Styrene monomer is a volatile organic compound that has many applications in plastics, rubber, and paint manufacturing industries. Exposure to styrene vapor has certain effects, including suppression of the central nervous system, loss of concentration, weakness and fatigue, and nausea and there is a possibility of carcinogenesis in long-term exposure. Therefore, it is necessary to control and eliminate this vapor. The aim of this study was to investigate the performance of zinc oxide nanoparticles on modified natural zeolites in removing styrene vapor from the air. Natural zeolites of clinoptilolite were modified using hydrochloric acid and diphenyldichlorosilane. Next, zinc oxide nanoparticles with different ratios of 3, 5, and 10 wt% were stabilized on the zeolites. To determine their characteristics, samples were used from BET, SEM and XRD analyses. The input styrene concentration and the ratio of nanoparticles stabilized on zeolites were studied as effective functional parameters on the removal process. The efficiency results of natural zeolites (Ze) and modified zeolites (Mze) in styrene adsorption from the air show that the styrene breakthrough in the bed of MZe compared to that of Ze increases approximately two times. Also, the results showed that the removal by the process of UV/MZe-ZnO 3%, UV/MZe-ZnO 5%, and UV/MZe-ZnO 10%, was 36.5%, 40%, and 26%, respectively. From the results it can be concluded that MZe can increase the efficiency of photocatalytic degradation. Clinoptilolites of Iran can be used as an adsorbent to remove polluted air in industries that have low concentrations and flow rates.     

Effect of modified single‐wall carbon nanotubes on mechanical and morphological properties of thermoplastic elastomer nanocomposites based on (polyamide 6)/(acrylonitrile butadiene rubber)

Thermoplastic elastomer nanocomposites based on acrylonitrile butadiene rubber (NBR) and polyamide 6 (PA6), with acid functionalized single‐wall carbon nanotubes (SWNT), were prepared via a direct melt‐mixing process in an internal mixer. The influence of SWNT content (0, 0.5, 1, 1.5) on morphological properties of PA6/NBR with different ratios (80/20, 70/30, 60/40) were then investigated. Characterization of nanocomposites was conducted by using transmission electron microscopy, scanning electron microscopy, differential scanning calorimetry, and mechanical properties. Scanning electron microscopy micrographs proved the droplet‐matrix blend morphology in which the size of NBR droplets decreased as the SWNT loading increased, suggesting dispersion of SWNT in the PA6 phase. It was further proved by transmission electron microscopy images, showing homogenous dispersion of SWNT in the PA6 phase. Differential scanning calorimetry results showed a slightly reduced percentage of crystallinity in samples containing SWNT. The mechanical properties of nanocomposites indicated an enhancement in tensile strength, modulus, and hardness on increasing SWNT content. J. VINYL ADDIT. TECHNOL., 22:336–341, 2016. © 2014 Society of Plastics Engineers     

Numerical investigation of grooves effects on the thermal performance of helically grooved shell and coil tube heat exchanger

Heat exchangers are integral parts of important industrial units such as petrochemicals, medicine and power plants. Due to the importance of systems energy consumption, different modifications have been applied on heat exchangers in terms of size and structure. In this study, a novel heat exchanger with helically grooved annulus shell and helically coiled tube was investigated by numerical simulation. Helically grooves with the same pitch of the helical coil tube and different depth are created on the inner and outer wall of annulus shell to improve the thermal performance of heat exchanger. In the first section, thermal performance of the shell and coil heat exchanger with the helical grooves on its outer shell wall was compared with same but without helical grooves. At the second section, helically grooves created on both outer and inner wall of the annulus shell with different groove depths. The results showed that the heat exchanger with grooves on both inner and outer shell wall has better thermal performance up to 20% compared to the heat exchanger with grooves on only outer shell wall. The highest thermal performance achieves at lower flow rates and higher groove depths whereas the pressure drop did not increase significantly.     

Fault diagnosis of an automobile cylinder head using low frequency vibrational data

This paper proposes a vibration-based fault-diagnosis method for mechanical parts. This method, after algorithm development, only requires a single inexpensive test to inspect the part which could take as short as half a second. The algorithm is developed in three major stages, (i) exciting specimens without or with known faults using a controlled force and recording acceleration of a single point for a short time (ii) finding a signature for each faulty specimen, using Fourier transform and statistical analysis. (iii) Developing a multi-layer perceptron, as a mathematical model, using the results of stage (ii). The elements of a part signature are the inputs to the model. The location (and possibly size and shape factor) of the fault is model output. Stage (i) can be performed experimentally or alternatively with a validated FEM, one experiment or simulation per specimen. The proposed technique was examined to locate (isolate) a fault on an automobile cylinder head. The presented accuracy is considerable, and the data collected at fairly low frequency range (below 1200 Hz) were found to be sufficient for this technique. In the case study of this paper, possible fault locations are on a line; as a result, fault location has one dimension. It is shown that the technique can be extended to higher dimensions.     

Effect of process variables on product yield distribution in thermal catalytic cracking of naphtha to light olefins over Fe/HZSM-5

The effect of temperature, WHSV and Fe loading over HZSM-5 catalyst in thermal-catalytic cracking (TCC) of naphtha for the production of light olefins has been studied. The response surface defined by three most significant parameters is obtained from Box-Behnken design method and the optimal parameter set is found. The results show that ethylene increases with temperature, while propylene shows an optimum at 650 °C. Moderate WHSV is favorable for maximum production of light olefins. Addition of Fe to HZSM-5 has a favorable effect on the production of light olefins up to 6% of loading. Excess amount of loading decreases the conversion of naphtha, which leads to a drop in light olefin yields. The yield of light olefins (ethylene and propylene) at 670 °C, 44 hr⁻¹ and 6 wt% Fe has been increased to 5.43 wt% compared to the unmodified HZSM-5 and reaches to 42.47 wt%.     

On-line analysis of out-of-control signals in multivariate manufacturing processes using a hybrid learning-based model

Advanced automatic data acquisition is now widely adopted in manufacturing industries and it is common to monitor several correlated quality variables simultaneously. Most of multivariate quality control charts are effective in detecting out-of-control signals based upon an overall statistics in multivariate manufacturing processes. The main problem of such charts is that they can detect an out-of-control event but do not directly determine which variable or group of variables has caused the out-of-control signal and what is the magnitude of out of control. This study presents a hybrid learning-based model for on-line analysis of out-of-control signals in multivariate manufacturing processes. This model consists of two modules. In the first module using a support vector machine-classifier, type of unnatural pattern can be recognized. Then by using three neural networks for shift mean, trend and cycle it can be recognized magnitude of mean shift, slope of trend and cycle amplitude for each variable simultaneously in the second module. The performance of the proposed approach has been evaluated using two examples. The output generated by trained hybrid model is strongly correlated with the corresponding actual target value for each quality characteristic. The main contributions of this work are recognizing the type of unnatural pattern and classification major parameters for shift, trend and cycle and for each variable simultaneously by proposed hybrid model.     

Three-dimensional free vibration of variable thickness thick circular and annular isotropic and functionally graded plates on Pasternak foundation

This paper describes a study of three-dimensional free vibration analysis of thick circular and annular isotropic and functionally graded (FG) plates with variable thickness along the radial direction, resting on Pasternak foundation. The formulation is based on the linear, small strain and exact elasticity theory. Plates with different boundary conditions are considered and the material properties of the FG plate are assumed to vary continuously through the thickness according to power law. The kinematic and the potential energy of the plate-foundation system are formulated and the polynomial-Ritz method is used to solve the eigenvalue problem. Convergence and comparison studies are done to demonstrate the correctness and accuracy of the present method. With respect to geometric parameters, elastic coefficients of foundation and different boundary conditions some new results are reported which may be used as benchmark solutions for future researches.