基于FCM燃料的商业压水堆中子学分析

全陶瓷微封装(Fully Ceramic Microencapsulated,FCM)燃料是一种将三结构同向性型(Tri-structural isotropic,TRISO)燃料颗粒弥散于SiC基质的先进燃料,具有良好的包容裂变产物的能力,能有效地改善核燃料在严重事故下保持结构完整性的能力,有利于降低核电站发生大量放射性物质泄漏的风险,是耐事故燃料(Accident Tolerant Fuel,ATF)的主要研究方向之一。与传统UO_2陶瓷芯块燃料相比,FCM燃料的U装量较少,且燃料基体采用SiC,慢化能力较好,可能导致FCM燃料应用于商业压水堆时寿期初慢化剂温度系数为正,不能满足堆芯的固有安全性。本文以标准AFA3G 17×17栅格形式的UO_2-Zr合金燃料组件为参照对象,采用中核集团自主研发的NESTOR软件,分析了17×17和13×13两种栅格形式的FCM燃料(UN核芯)组件的中子学特性,评价了由13×13栅格形式的FCM燃料(UN核芯)组成反应堆堆芯的总体物理特性。研究表明:含钆可燃毒物的13×13栅格形式的FCM燃料(UN核芯)组件可满足欠慢化要求,13×13栅格形式的FCM燃料(UN核芯)用于大型商业压水堆堆芯的慢化剂温度系数可以为负,首循环堆芯可达到与参照堆芯接近的燃耗深度与循环长度,能初步满足商业压水堆堆芯的固有安全性和经济性的要求。     

脉冲高度权重技术测量197Au中子俘获截面

脉冲高度权重技术是利用C_6D_6探测器测量中子俘获截面的一种数据处理方法。在中国散裂中子源(China Spallation Neutron Source,CSNS)的反角白光中子源(Back-n)靶站上,通过测量金靶(~(197)Au)的中子俘获截面,验证了该方法的可靠性。首先利用Geant4蒙特卡罗程序模拟给出了不同靶条件下的探测器效率,脉冲高度权重函数等基本项,使得加权后的探测器效率与γ能量成正比。然后通过实验测量了~(197)Au中子俘获截面。结果表明:测量获得的中子俘获截面数据和ENDF/B-VⅢ.0评价数据相符合,同时发现随着实验靶尺寸的不同和质子束功率的增加,会使得实验本底的扣除误差越来越大。     

Broad-Spectral-Range Sustainability and Controllable Excitation of Hyperbolic Phonon Polaritons in α-MoO3

Hyperbolic phonon polaritons (HPhPs) in orthorhombic-phase molybdenum trioxide (α-MoO₃) show in-plane hyperbolicity, great wavelength compression, and ultralong lifetime, therefore holding great potential in nanophotonic applications. However, its polaritonic response in the far-infrared (FIR) range remains unexplored due to challenges in experimental characterization. Here, monochromated electron energy loss spectroscopy (EELS) in a scanning transmission electron microscope (STEM) is used to probe HPhPs in α-MoO₃ in both mid-infrared (MIR) and FIR frequencies and correlate their behaviors with microstructures and orientations. It is found that low structural symmetry leads to various phonon modes and multiple Reststrahlen bands (RBs) over a broad spectral range (over 70 meV) and in different directions (55–63 meV and 119–125 meV along the b-axis, 68–106 meV along the c-axis, and 101–121 meV along the a-axis). These HPhPs can be selectively excited by controlling the direction of swift electrons. These findings provide new opportunities in nanophotonic and optoelectronic applications, such as directed light propagation, hyperlenses, and heat transfer.     

Precise Extraction of Charge Carrier Mobility for Organic Transistors

Unreliable mobility values, and particularly greatly overestimated values and severely distorted temperature dependences, have recently hampered the development of the organic transistor field. Given that organic field‐effect transistors (OFETs) have been routinely used to evaluate mobility, precise parameter extraction using the electrical properties of OFETs is thus of primary importance. This review examines the origins of the various mobilities that must be determined for OFET applications, the relevant extraction methods, and the data selection limitations, which help in avoiding conceptual errors during mobility extraction. For increased precision, the review also discusses device fabrication considerations, calibration of both the specific gate‐dielectric capacitance and the threshold voltage, the contact effects, and the bias and temperature dependences, which must actually be handled with great care but have mostly been overlooked to date. This review serves as a systematic overview of the OFET mobility extraction process to ensure high precision and will also aid in improving future research.     

积分中值屈服准则解析厚板轧制椭圆速度场

为解决非线性Mises比塑性功率积分困难以及由此导致的轧制功率解析式难以获得的问题,本文通过建立并利用线性比塑性功率表达式对提出的椭圆速度场进行能量分析,得到了轧制力能参数的解析解.文中通过对变角度屈服函数求积分中值,构建了一个新的屈服准则,它是主应力分量的线性组合,在π平面上的轨迹是逼近Mises圆的等边非等角的十二边形,其基于Lode参数表达式的理论结果也与实验数据吻合较好.同时,根据厚板轧制时金属流动速度从入口到出口逐渐增大的特点,提出了水平速度分量满足椭圆方程的速度场,该速度场满足运动许可条件.通过相应的轧制能量分析,获得了基于线性屈服准则的内部变形功率以及基于应变矢量内积法上的摩擦功率与剪切功率.在此之上,通过泛函的极值变分导出了轧制力矩、轧制力以及应力状态系数的解析解,并与现场实测数据进行了对比,结果表明利用本文提出的屈服准则与速度场所建立的轧制力矩与轧制力模型与实测值吻合较好,其中轧制力误差小于5.3%,轧制力矩误差在6%左右.     

柠条的纤维特性及其双螺杆CMP制浆性能研究

以柠条为原料，分析了其化学组分和纤维形态，并探讨了柠条双螺杆CMP法的制浆工艺以及浆料的纤维形态和成纸的物理性能。研究结果表明：与针、阔叶木相比，柠条原料中纤维素和综纤维素质量分数较低，苯醇抽出物和热水抽出物质量分数较高，柠条纤维长度总体偏短，木质部和皮部的纤维质量平均长度分别为0.621和0.819 mm，还存在部分杂细胞。采用3.5% Na₂SO₃和1.5% NaOH常温预浸12 h、90℃汽蒸1 h后再用双螺杆挤浆机在质量分数35%下进行搓丝，并结合高浓盘磨机磨浆，所得CMP浆得率可达73%。柠条CMP浆基本保持了纤维原有的长度，质量平均长度达0.650 mm，长宽比为32.7，纤维解离较好，但分丝帚化情况不理想，含有部分纤维束和杂细胞。当加拿大游离度为300 mL时，柠条CMP浆成纸的环压强度指数和松厚度较高，分别为8.67（N·m）/g和2.56 cm³/g，抗张指数为19.6（N·m）/g，本色浆白度较高，达50%（ISO）。柠条CMP浆适合配抄瓦楞原纸等包装用纸，漂白后可配抄新闻纸和白板纸。     

Dual Inhibition of Pyruvate Dehydrogenase Complex and Respiratory Chain Complex Induces Apoptosis by a Mitochondria-Targeted Fluorescent Organic Arsenical in vitro and in vivo

Based on the potential therapeutic value in targeting mitochondria and the fluorophore tracing ability, a fluorescent mitochondria-targeted organic arsenical PDT-PAO-F16 was fabricated, which not only visualized the cellular distribution, but also exerted anti-cancer activity in vitro and in vivo via targeting pyruvate dehydrogenase complex (PDHC) and respiratory chain complexes in mitochondria. In details, PDT-PAO-F16 mainly accumulated into mitochondria within hours and suppressed the activity of PDHC resulting in the inhibition of ATP synthesis and thermogenesis disorder. Moreover, the suppression of respiratory chain complex I and IV accelerated the mitochondrial dysfunction leading to caspase family-dependent apoptosis. In vivo, the acute promyelocytic leukemia was greatly alleviated in the PDT-PAO-F16 treated group in APL mice model. Our results demonstrated the organic arsenical precursor with fluorescence imaging and target-anticancer efficacy is a promising anticancer drug.     

多肽N端修饰方法研究进展

多肽是源于生物体内的一类重要的生物活性物质,但由于稳定性差等原因,大大限制了其应用。通过对多肽进行结构修饰,可以改变其理化性质,进而提高其稳定性及生物活性。综述了近年来多肽N端修饰方法的研究进展,包括乙酰化、PEG(聚乙二醇)修饰、荧光试剂修饰、多肽N端亲水性基团修饰、NCL及EPL连接反应等,介绍了2-氨基辛酸、丁烯酶1、N-脒基-焦谷氨酰苯丙氨酸、N-terminal caps等多肽N端修饰实例。     

高密度聚乙烯/丁苯橡胶热塑性硫化胶的形状记忆性能

采用动态硫化法制备了高密度聚乙烯(HDPE)/丁苯橡胶(SBR)热塑性硫化胶(TPV),研究了橡塑比、定型温度、回复温度及增容剂苯乙烯-丁二烯-苯乙烯嵌段共聚物(SBS)对HDPE/SBR TPV形状记忆性能的影响,观察了其微观结构,提出了形状记忆行为机制。结果表明,HDPE/SBR TPV具有典型的"海-岛"结构,拉伸后其表面存在明显的取向结构;SBS能显著提高HDPE/SBR TPV的形状记忆性能,当SBS用量为6份、定型温度和回复温度均为120℃时,HDPE/SBR TPV的形状记忆性能最佳。