B4C–TiB2 composites fabricated by hot pressing TiC–B mixtures: The effect of B excess

Previous research have reported that B₄C–TiB₂ composites could be prepared by the reactive sintering of TiC–B powder mixtures. However, due to spontaneous oxidation of raw powders, using TiC–B powder mixtures with a B/TiC molar ratio of 6: 1 introduced an intermediate phase of C during the sintering process, which deteriorated the hardness of the composites. In this report, the effects of B excess on the phase composition, microstructure, and mechanical properties of B₄C–TiB₂ composites fabricated by reactive hot pressing TiC–B powder mixtures were investigated. XRD and Raman spectra confirmed that lattice expansion occurred in B-rich boron carbide and B_xC–TiB₂ (x > 4) composites were obtained. The increasing B content improved the hardness and fracture toughness but decreased the flexural strength of B_xC–TiB₂ (x > 4) composites. When the molar ratio of B/TiC increased from 6.6:1 to 7.8:1, the Vickers hardness and the fracture toughness of the composites were enhanced from 26.7 GPa and 4.53 MPa m^1/2 to 30.4 GPa and 5.78 MPa m^1/2, respectively. The improved hardness was attributed to the microstructural improvement, while the toughening mechanism was crack deflection, crack bridging and crack branching.     

An Optimized Combination of Mine Water Control,Treatment, Utilization,and Reinjection for Environmentally Sustainable Mining: A Case Study

This paper presents a case study of an optimized combination of mine water control, treatment, utilization and reinjection to achieve the zero discharge of mine water. Mine water has been considered a hazard and pollution source during underground mining, so most mining enterprises directly discharge mine water to the surface after simple treatment, resulting in a serious waste of water. Moreover, discharging a large amount of mine water can destroy the original groundwater balance and cause serious environmental problems, such as surface subsidence, water resource reduction and contamination, and adverse impacts on biodiversity. The Zhongguan iron mine is in the major groundwater source area of the Hundred Springs of Xingtai, which is an area with a high risk of potential subsidence. To optimize the balance between mining and groundwater resources, a series of engineering measures was adopted by the Zhongguan iron mine to realize mine water control, treatment, utilization, and reinjection. The installation of a closed grout curtain has greatly reduced the water yield of deep stopes in the mine; the effective sealing efficiency reaches 80%. Nanofiltration membrane separation was adopted to treat the highly mineralized mine water; the quality of the produced water meets China’s recommended class II groundwater standard. Low-grade heat energy from the mine water is collected and utilized through a water-source heat pump system. Finally, zero mine water discharge is realized through mine water reinjection. This research provides a beneficial reference for mines with similar geological and hydrogeological conditions to achieve environmentally sustainable mining.

     

Synthesis,characterization, and visible-light photocatalytic activity of transition metals doped ZTO nanoparticles

Transition metals doping has been proved to be a feasible way for tuning the physical properties on the surface and bulk of nanomaterials and also for the good performance in decontamination of emerging pollutants. In this context, doped samples of zinc tin oxide or zinc stannate nanoparticles (ZTO NPs) by several transition metals were synthesized in order to enhance the optical absorbance with the aims of reducing the band gap and therefore ameliorated their photocatalytic activity. They were characterized by the X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy, Raman spectroscopy and photoluminescence. The XRD patterns and the microscopic observations showed the formation of spherical nanoparticles with an average size of about 30 nm and highly pure ZTO phase with an inverse spinel structure. The Raman spectra were dominated by bands relatives to the F2g (2) and A1g symmetries modes of inverse spinel structure. The band gap Eg is estimated to be 3.75 eV for the undoped sample, and 3.67, 3.64, 3.78 and 3.21 eV, for 2% Fe, 2% Mg, 2% Gd, and 2% Mn doped ZTO samples, respectively.Furthermore, the undoped ZTO NPs have the intrinsic problem of recombination of photogenerated charge carriers. We have shown that the reduction of the band gap and oxygen vacancies resulting from the doping effect could be a useful tool for trapping and avoid the recombination of electrons coming from photosensitized rhodamine B (RhB) under visible light irradiation. Owing to the structural advantages and low band gap, 2% Mn doped ZTO NPs, with the kinetic rate constants k of 0.024 min⁻¹, show enhanced performance for the elimination of RhB in aqueous solution compared to undoped and other doped ZTO NPs.     

Transparent and flexible films of new segmented polyurethane nanocomposites incorporated by NH2-functionalized TiO2 nanoparticles

In this work, TiO₂ nanoparticles are surface modified by NH₂-terminated organic moieties arised from 4,4′-methylene diphenyl diisocyanate (MDI). These nanoparticles are incorporated into ether-based segmented polyurethane (SPU) matrix. MDI is utilized as monomer together with poly(tetramethylene oxide) (PTMO) comonomer for preparing the final polymer as well. The NH₂-functionalized TiO₂ nanoparticles are covalently linked to the NCO terminals of the resulting SPU macromolecules during film preparation stage. Therefore, in addition to butylene glycol, these surface modified nanoparticles with enhanced organophilicity could play the role of the second chain extender of NCO-capped SPU macromolecules through formation of urea linkages. Optical and thermal behaviors of the transparent and flexible film (SPU/TiO₂–MDI) is compared with those of unmodified TiO₂ (SPU/TiO₂) and TiO₂-unloaded SPU films. Though the particle loading is only 5 wt.%, incorporation of TiO₂ and TiO₂–MDI nanoparticles into the SPU polymer enhances significantly the light absorption in UV region at 300–400 nm. SEM images of the prepared films clearly show a considerable decrease in particle aggregation for TiO₂–MDI into SPU matrix compared to that of unmodified TiO₂. TG analyses indicate a one-step decomposition pattern with onset temperatures of about 360 and 380 °C for neat SPU and SPU/TiO₂–MDI, respectively. Moreover, DTA thermograms of both nanocomposites show obviously two exothermic phase transitions in the thermal range of 330–440 °C.     

Diffusion behavior of dextrans in dairy systems of different microstructures

The diffusion of solutes through milk and milk-derived media (i.e. dairy systems) is an important factor in the transformation and stabilization of dairy products. In several polymer systems, the diffusion of solutes largely depends on the microstructure within the material. The aim of this work was to establish how the diffusion of solutes is affected by the microstructure of dairy systems. Diffusion measurements were carried out using the technique of fluorescence recovery after photobleaching (FRAP). Diffusion coefficients of a range of 8 fluorescein isothiocyanate (FITC)–dextrans (molecular weights from 4 to 2000 kDa) were measured in dairy systems. These systems had the same casein concentration (130 g kg^− 1) and water activity but their microstructure had been altered by different treatments: heat-treatment and rennet-induced coagulation. Microstructural parameters of these systems were estimated by the image analysis of transmission electron microscopy (TEM) micrographs. The results showed that the diffusion of solutes was affected by the microstructure of dairy systems. The application of heat-treatment hindered the diffusion of all solutes (irrespective of molecular weight), whereas rennet coagulation only increased the diffusion of the larger solute molecules (> 20 kDa). At the microscopic scale, the diffusion of solutes in dairy systems was mainly explained by both the pore size within the structure and by the interface area between the solute molecules and the surrounding matrix. Larger solutes diffused faster in dairy systems with larger pore sizes and less interface area.     

Mechanical properties of graphene films enhanced by homo-telechelic functionalized polymer fillers via π–π stacking interactions

Most researches on graphene/polymer composites are focusing on improving the mechanical and electrical properties of polymers at low graphene content instead of paying attention to constructing graphene’s macroscopic structures. In current study the homo-telechelic functionalized polyethylene glycols (FPEGs) were tailored with π-orbital-rich groups (namely phenyl, pyrene and di-pyrene) via esterification reactions, which enhanced the interaction between polyethylene glycol (PEG) molecules and chemical reduced graphene oxide (RGO) sheets. The π–π stacking interactions between graphene sheets and π-orbital-rich groups endowed the composite films with enhanced tensile strength and tunable electrical conductivity. The formation of graphene network structure mediated by the FPEGs fillers via π–π stacking non-covalent interactions should account for the experimental results. The experimental investigations were also complemented with theoretical calculation using a density functional theory. Atomic force microscope (AFM), scanning electron microscope (SEM), X-ray diffraction (XRD), nuclear magnetic resonance (NMR), thermal gravimetric analysis (TGA), UV–vis and fluorescence spectroscopy were used to monitor the step-wise preparation of graphene composite films.     

Grain size influence on the flexibility and luminous intensity of inorganic CaTiO3:Pr3+ crystal nanofibers

Traditional inorganic materials exhibit rigidity owing to the lack of polymer chains in polymer materials or atom slipping in metals. However, nanometerization has been recently proposed for the conversion of inorganic oxide materials into flexible materials. Herein, the flexible inorganic luminescent material, CaTiO₃:0.2%Pr³⁺, was synthesized through electrospinning, and the macroscopic flexibility of pure inorganic CaTiO₃:0.2%Pr³⁺ was achieved. The flexible membrane was characterized via X-ray diffraction, thermogravimetry, scanning electron microscopy (SEM), and photoluminescence analyses. The grain size was analyzed at various calcination temperatures via SEM, and the results suggested that the increase in the calcination temperature resulted in the growth of crystal grains. Studies have reported that the growth of crystal grains is beneficial for improving the luminescence performance; however, to obtain better flexibility, smaller crystal grains are required. This study provides an important reference for the design of flexible inorganic materials.     

Adaptive Finite-time Tracking Control for Class of Uncertain Nonlinearly Parameterized Systems with Input Delay

International Journal of Control, Automation and Systems - In this paper, the tracking problem for a class of uncertain nonlinearly parameterized systems with input delay based the adaptive...     

Single copper sites dispersed on hierarchically porous carbon for improving oxygen reduction reaction towards zinc-air battery

The demand for high-performance non-precious-metal electrocatalysts to replace the noble metal-based catalysts for oxygen reduction reaction(ORR)is intensively increasing.Herein,single-atomic copper sites supported on N-doped three-dimensional hierarchically porous carbon catalyst(Cu₁/NC)was prepared by coordination pyrolysis strategy.Remarkably,the Cu₁/NC-900 catalyst not only exhibits excellent ORR performance with a half-wave potential of 0.894 V(vs.RHE)in alkaline media,outperforming those of commercial Pt/C(0.851 V)and Cu nanoparticles anchored on N-doped porous carbon(CuNPs/NC-900),but also demonstrates high stability and methanol tolerance.Moreover,the Cu₁/NC-900 based Zn-air battery exhibits higher power density,rechargeability and cyclic stability than the one based on Pt/C.Both experimental and theoretical investigations demonstrated that the excellent performance of the as-obtained Cu₁/NC-900 could be attributed to the synergistic effect between copper coordinated by three N atoms active sites and the neighbouring carbon defect,resulting in elevated Cu d-band centers of Cu atoms and facilitating intermediate desorption for ORR process.This study may lead towards the development of highly efficient non-noble metal catalysts for applications in electrochemical energy conversion.