基于GIS单线图的配网停电单模拟操作应用研究

配电网停电会造成电力系统供配电可靠性以及服务质量下降,研究基于地理信息系统(GIS)单线图的配网停电单模拟操作应用。利用网格长度作为基本单位建立坐标系,以选取起始点与终止点为基础,通过四参数法将GIS坐标映射至图纸网格内,实现配网内设备初步布局,将杆塔、站房和整体均匀分布作为优化目标,设置多目标优化目标函数实现GIS单线图最终优化。选取某电力公司配网作为单模拟操作应用对象,模拟结果表明,单模拟操作配网停电后,该配网各负荷点年故障率、次平均停电时间以及年停电时间均有所减少,可有效提升配网的供配电可靠性。     

碳酸盐岩岩溶储层多井评价方法及地质应用

多井评价是建立在单井精细解释对比分析基础上的预测储层及含油气性平面分布规律的技术方法,而常规测井资料无法区分碳酸盐岩岩溶储层,因而利用多井评价结果确定岩溶发育程度在平面上的分布规律就显得十分重要。为此,在岩心标定成像测井的基础上,对四川盆地高石梯—磨溪地区15口井的成像测井岩溶发育特征进行分析,建立了中二叠统茅口组岩溶发育各分带的标准成像图版,利用交会图及直方图分析各分带的常规测井响应特征,在此基础上形成了电成像测井刻度常规测井识别岩溶发育带的新方法。研究结果表明:①高石梯—磨溪地区茅口组岩溶带自上而下可划分为风化壳残积带、垂直渗流岩溶带、水平潜流岩溶带以及受岩溶作用较弱的基岩;②风化壳残积带在成像测井图像显示为"暗—亮—暗"条带状模式,垂直渗流岩溶带为垂直线状与暗色斑状组合模式,水平潜流岩溶带为水平线状—层状与斑状组合模式,基岩整体显示为亮色块状模式偶见线状或斑状特征;③有效储层主要发育在垂直渗流带和水平潜流带的顶部;④该区茅口组岩溶发育主要受裂缝发育控制,而裂缝发育又与断层关系密切。结论认为,该新方法对碳酸盐岩岩溶储层的多井评价具有普遍适用性,为四川盆地中二叠统风险探井的部署提供了技术支撑。     

小型机载激光通信系统设计与验证

针对空空宽带高速通信的需求，设计了小型化机载激光通信系统。仿真分析了300 km、2.5 Gb/s无线激光链路性能，并通过运动仿真台模拟机动环境测试了系统的跟踪与通信性能，其中粗跟踪误差为533.2 μrad(1σ)，精跟踪误差为3.6 μrad(1σ)，测试数据传输240 s，通信误码率为2.82×10-9。仿真与实验验证了该系统用于远距离空空无线激光通信的可行性。     

Performance investigation on a novel 3D wave flow channel design for PEMFC

Flow field structure can largely determine the output performance of Polymer electrolyte membrane fuel cell. Excellent channel configuration accelerates electrochemical reactions in the catalytic layer, effectively avoiding flooding on the cathode side. In present study, a three-dimensional, multi-phase model of PEMFC with a 3D wave flow channel is established. CFD method is applied to optimize the geometry constructions of three-dimensional wave flow channels. The results reveal that 3D wave flow channel is overall better than straight channel in promoting reactant gases transport, removing liquid water accumulated in microporous layer and avoiding thermal stress concentration in the membrane. Moreover, results show the optimal flow channel minimum depth and wave length of the 3D wave flow channel are 0.45 mm and 2 mm, respectively. Due to the periodic geometric characteristics of the wave channel, the convective mass transfer is introduced, improving gas flow rate in through-plane direction. Furthermore, when the cell output voltage is 0.4 V, the current density in the novel channel is 23.8% higher than that of conventional channel.     

Advances in the in vitro digestion and fermentation of polysaccharides

In vitro digestion models are widely used to study the structural changes, digestion and release of food components under simulated gastrointestinal conditions. As compared to the in vivo digestion tests, the in vitro digestion reflects the digestion and utilisation of food after ingestion and has the advantages of being time consuming, inexpensive, reproducible and free from moral and ethical restrictions. This study reviewed the current research studies on the in vitro simulated digestion of polysaccharides conducted in the last 5 years and focused on the oral, gastric and intestinal digestion models, with the aim of providing a basis for the further testing of changes in the content, structure and active ingredients of polysaccharides before and after digestion.     

基于蛋白质组学技术研究秦川牛肉宰后贮藏过程中肌红蛋白含量及其衍生物转化

本实验采用4D-非标记蛋白质组学技术研究秦川牛肉贮藏过程中（0～8 d）肌红蛋白含量及其衍生物的转化情况，阐释冷却秦川牛肉中肌红蛋白含量及其衍生物转化的分子机制。结果表明：贮藏过程中，肌红蛋白表达量在宰后0～4 d上升、4～8 d下降，利用非标记蛋白质组学技术鉴定出与肌红蛋白及其衍生物相关的差异蛋白14 种，具体包括代谢酶、氧化还原酶、过氧化物酶、伴侣蛋白4 类，这4 类蛋白的表达共同调控贮藏过程中肌红蛋白含量的变化及其3 种衍生物之间的转化，具体表现为贮藏过程中肌红蛋白表达量整体呈下降趋势，氧合肌红蛋白相对含量持续下降，脱氧肌红蛋白、高铁肌红蛋白相对含量逐渐增加，导致肉色发生褐变。本研究结果有利于理解秦川牛肉贮藏过程肉类变色的复杂生化变化机制。     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

面向草莓抓取的气动四叶片软体抓手研制

农林业中果蔬的自动化采摘需求日趋强烈,末端抓手是实现无损采摘的关键。传统的末端抓手以刚性结构居多,现有的各种柔性抓手也存在抓取力不足、包覆性不佳等缺点。本文以草莓的无损采摘为研究对象,提出将草莓外部轮廓曲线作为设计曲线,设计了一种新型气动四叶片软体抓手。首先,对软体抓手的结构做仿真优化,提出一种安全地附着在目标物表面的设想。然后,在进行草莓表面的最小破坏应力试验的基础上,测试了软体抓手的末端力,验证了其实现无损抓取的可行性。再次,利用动态捕捉技术,研究了软体抓手叶面的弯曲变形规律。最后,选择使用弧线型气体通道的软体抓手进行了草莓抓取测试,结果证明了气动四叶片软体抓手可以实现草莓的无损抓取,抓取成功率达90%,破损率为2%,表明所研制的四叶片软体抓手用于草莓抓取时具有良好的稳定性和实用性,可用于草莓采摘的末端执行器。本研究也可为其他易损果蔬的采摘技术提供理论基础和技术支撑。