Preparation and antifouling performance of thin inorganic ultrafiltration membrane via assisted sol-gel method with different composition of dual additives

A novel TiO₂ thin film was prepared on the ceramic hollow fiber by the sol-gel method using poly(vinylpyrrolidone) (PVP) and polyvinyl alcohol (PVA) as additives. SEM images verified the formation of TiO₂ layer with various thickness using different composition of titania sols. The effect of the PVP and PVA contents on the TiO₂ sol properties, the separation and the antifouling performance of the ultrafiltration membranes were investigated thoroughly. When the contents of PVP and PVA were 1.0 wt% and 0.8 wt%, respectively, the resultant membrane showed a thickness of 0.55 μm with a pure water flux of 255 L m^?2 h^?1. In addition, the adherent foulant bovine serum albumin was applied to evaluate the antifouling performance. During the three fouling-recovery cycles, the flux recovery ratio and the flux decay ratio maintained about 99% and 30%. The BSA flux and rejection were still 169 L m^?2 h^?1 and 96.9% after the cycles, indicating a superior antifouling property.     

气相色谱法测定焦油中微量苯稠杂环化合物

利用蒸馏分离—气相色谱法技术,建立了同时测定煤焦油中苊、氧芴和芴的分析方法。通过对色谱条件的优化,以甲苯为溶剂,正十二烷为内标物,将煤焦油馏分采用DB-5毛细管柱,对煤焦油中苊、氧芴和芴定量分析。分析结果表明:3种主要成分线性关系良好,相关系数均大于0.9995,加标回收率为95.4%~102.4%,相对标准偏差为2.89%~7.14%。该方法分离效果好,检测结果准确、可靠。     

破损水文观测孔涌水封堵技术在高河矿的应用

针对高河矿奥灰水文观测孔空水管锈蚀断裂漏水严重的问题,分析了存在的问题,制定了钻孔涌水封堵技术方案及相应的注浆施工工艺,并进行了为期7天的井下试验。封堵注浆压力达到6 MPa,使用注浆水泥50 t,水泥浆液凝固良好,注浆阀门打开后无出水现象。     

Experimental investigation of different morphology textured ceramic tools by in-situ formed for the dry cutting

Surface texture is considered an important measure to improve the cutting performance of a tool. In this study, we have prepared three types of textured and conventional tools on the rake face by an in-situ formed method. During the experiment, the best parameters of three types of textured tools were selected for dry cutting AISI 1045 steel at different cutting speeds. Cutting forces, cutting temperatures, workpiece surface roughness, and tool wear were measured during the cutting process. The results showed that textured tools have significantly reduced cutting force, cutting temperature, and tool wear, and the roughness of the workpiece was improved compared with the conventional tool. The micro-pit texture tool has less stress contact region than the micro-groove width texture tool, but the micro-groove width texture tool exhibiting the best cutting performance. This investigation clearly showed that the textured tool prepared by the in-situ formed method has improved cutting performance.     

New exact solutions of the Tzitzéica-type equations in non-linear optics using the expa function method

One specific class of non-linear evolution equations, known as the Tzitzéica-type equations, has received great attention from a group of researchers involved in non-linear science. In this article, new exact solutions of the Tzitzéica-type equations arising in non-linear optics, including the Tzitzéica, Dodd–Bullough–Mikhailov and Tzitzéica–Dodd–Bullough equations, are obtained using the exp_a function method. The integration technique actually suggests a useful and reliable method to extract new exact solutions of a wide range of non-linear evolution equations.     

DyCrxFe(1-x)O3 nanoparticles prepared by wet chemical technique for photocatalytic applications

DyCr_xFe_(1-x)O₃ (0 ≤ x ≥ 0.4) nanoparticles were prepared using facile chemical route. Structural and morphological evaluation was carried out using X-ray diffraction (XRD) and electron microscopy. Formation of orthorhombic DyFeO₃ nanoparticles was confirmed by XRD with crystallite size of 9–10 nm. FESEM images revealed nearly spherical morphology of the fabricated nanoparticles. Energy dispersive X-ray (EDX) technique was employed to confirm the presence of Dy, Cr, Fe and O elements in DyCr_xFe_(1-x)O₃ nanoparticles. FTIR studies illustrated the presence of characteristics stretching and bending vibrations. UV–visible spectroscopy was used to analyze the photocatalytic performance of the DyFeO₃ and Cr-substituted DyFeO₃ nanoparticles and optical band gap measurements. Photocatalytic activities of the prepared substituted and un-substituted DyFeO₃ nanoparticles were conducted using three different dyes. These dyes were (i) methyl orange, (ii) rhodamine B and (iii) methylene blue. Lower band gap and higher photocatalytic performance was observed for Cr-substituted DyFeO₃ nanoparticles with methylene blue dye.     

复杂炼油塔模拟的改进联立方程内外层算法

在内外层算法的基础上，采用联立方程思想将主塔、侧线汽提塔视为一个整体进行建模，并针对复杂炼油塔的特点对算法提出了改进。首先，由于传统内外层法简化的K值模型对组成的变化不敏感，在处理带有石油的体系时，容易出现迭代次数较多，甚至部分塔板温度更新异常的问题，因此采用了汽相分数加和式推导了简化的K值模型加权因子。其次，借鉴流量加和法思想，规定侧线汽提塔的塔底产品流量作为设计变量，增强了算法收敛的稳定性。为验证改进后算法的有效性，采用不同的算法对实际的常压塔进行了模拟，结果显示改进后的算法适合应用于复杂炼油塔的模拟计算。     

喷油方式对斜齿轮齿面温度的影响

为探讨喷油方式对齿面温度的影响，以斜齿轮为研究对象，通过CFD仿真和试验研究不同喷油方式对斜齿轮齿面温度的影响。针对斜齿轮喷油润滑过程的特点，分析其齿面摩擦生热量，简化轮齿喷油润滑计算模型，并基于CFX进行齿面对流换热仿真研究，得到了不同喷油方式下的齿面温度；基于功率开放式斜齿轮试验平台，对不同喷油方式下的齿面温度进行了试验测量，与仿真计算结果进行对比分析。结果表明：在高速重载斜齿轮传动系统中，啮出侧喷油润滑的方式比啮入侧喷油润滑方式的冷却降温效果要好。     

面向医院建筑项目的IPD模式应用研究

医院建筑项目是非常复杂且具有挑战性的建设项目。传统的交付模式无法满足人们对医院建筑建设、运营方面的高要求,为此开展面向医院建筑项目的IPD模式应用研究。在对IPD模式发展现状整理的基础上,阐述医院建筑项目IPD模式的适用性。分析采用IPD模式的医院建筑项目特点,并以上海市某公立三甲专科医院项目为例,对IPD模式在国内的应用进行探索性研究。