CSTN-LCD用铬版清洗效果的改善

利用铬版清洗机对CSTN-LCD用铬版进行清洗处理,分析了清洗过程中出现的铬层脱落现象,铬层脱落与轴向喷射压力和水平切力密切相关,通过调整转速和喷射压力探索了安全使用条件:在转速不超过1000r/min,喷射压力低于0.5×105Pa的情况下使用铬版清洗机进行清洗是相对安全的。同时采用预清洗处理的方法满足清洁要求,使换线时间由平均3h缩短到平均1h以内,年产能提高270000片。     

The Precedence Effect in Three Species of Birds (Melopsittacus undulatus, Serinus canaria, and Taeniopygia guttata).

The perceived locations of paired auditory images, simulating direct sounds and their echoes, have been recently studied in budgerigars (Melopsittacus undulatus; M. L. Dent & R. J. Dooling, 2003a, 2003b). In this article, the authors extend those experiments to include measurements of the precedence effect using a discrimination paradigm in two additional bird species: canaries (Serinus canaria) and zebra finches (Taeniopygia guttata). Although time courses of summing localization, localization dominance, and echo thresholds were similar across all species, budgerigars had slightly higher overall levels of discrimination. The results from these experiments add further support that the precedence effect in birds is similar to that found in other animals and that the ability to suppress echoes that might degrade localization and auditory object perception may be a general property of the vertebrate auditory system. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Quality of Service in VoIP Communication

The focus of this paper lies in the practical aspects of voice over IP communication. VoIP configurations in the H.323 standard will be presented briefly. Following that, the fundamental protocol procedure of H.323 communication will be briefly explained. A further part of the paper will address the subject QoS (quality of service), and present the common measurement methods used in QoS. Results gained from experiments conducted in a VoIP environment will then follow. The investigations concentrate primarily on the load behavior of voice packets in relation to important parameters of this service. The results obtained are presented and evaluated in diagrams. The paper concludes with a summary.     

理想九点五态控制器原理的叙述

用计算的方式叙述理想九点五态控制器的控制原理。为便于人们理解二阶对象的运动中控制的变化过程,将抽象的对象转换为人们熟知的L-R-C电路,通过调节输入电压(即控制作用)的大小和方向来实现对对象性能的调节,并使系统达到理想的性能指标。最后用仿真来验证计算结果的正确性。     

Logistic模型的改进及在油藏可采储量预测中的应用

为了更准确地预测油气藏未来的经济可采储量，依据油气藏随开发必然要经历产量递减和生产收支平衡的实际。利用Logistic模型中技术可采储量、产量与时间的相互关系，经推导和改进后，再结合当前经济技术条件下的废弃产油量，预测油气藏的有效生产时间及其经济可呆储量。实践证实，改进后的Logistic模型预测结果更符合油气藏的生产实际，能为油气藏的储量管理提供可靠的依据。     

宝浪油田宝北区块低渗透油藏层系优化研究

针对宝浪油田宝北区块低孔低渗油藏地质特征以及油层层数多、分布井段长、部分零散层动用难度大等问题 ,研究了宝北区有效厚度、油层层数、单井产能及单井控制地质储量等层系划分与组合的技术经济界限 ,并在此基础上进行了宝北区层系划分与组合优化论证 ,最终优选出宝北区开发层系     

电荷耦合器件积分时间对微型成像系统成像质量的影响

在光圈固定的情况下，确定合适的积分时间对于提高微型电荷耦合器件(CCD)成像系统的成像质量，增强微型飞行器的侦察能力具有十分重要的意义。本文讨论了决定CCD积分时间的各种因素，重点研究了适用于微型飞行器的CCD成像系统的积分时间与像移的关系，并进一步推导了计算像移量的相关数学模型。利用该模型对不同积分时间内采集的运动图像进行了像质评价，结果表明，在保证曝光量的前提下，当像移量被限制在1个像素内时，可以获得相对理想的运动图像像质。     

海拉尔盆地的古河道砂体识别方法

本文基于海拉尔盆地贝尔凹陷西北部高精度三维地震资料,通过对时间域、频率域地震属性的分析,研究了河道砂体的变化及分布规律,总结出了一套利用时间域、频率域地震属性识别古河道的方法。其中对河道砂体较为敏感的沿层属性主要有均方根振幅、反射强度梯度、有效带宽及瞬时频度等。利用这种识别方法在该区找到水下分流河道砂体和河口坝砂体,为该区的岩性勘探部署提供了具体目标。     

Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

应用AR模型的IMU误差系数漂移预测研究

将影响IMU误差系数漂移并难于分离的多种因素综合为一种因素，假定IMU误差系数的漂移由一特定系统所引起，从而采用时间序列建模方法进行IMU误差系数漂移的预测。该方法具有消除各因素具体分析中的不确定性并减少其工作员的优点。文中描述了其原理，对某惯组的33个误差系数进行了时间序列建模与预测并得到有效的结果。最后还阐述了存在的问题及其解决方法。