少量有机碳对单级自养脱氮工艺性能的影响

采用序批式生物膜反应器(SBBR),经过4个阶段的培养,快速富集好氧氨氧化细菌(AOB)和厌氧氨氧化细菌(AnAOB),并考察不同低碳氮比对工艺脱氮性能的影响。结果表明,NH4^+-N去除率可达到99%以上,TN去除率可达到90%以上。对应C/N=0、1和2时,反应器出水NH4^+-N和TN去除率分别为99.59%、99.5%、98.47%和93.75%、97.22%、98.11%。说明少量COD的存在,可实现同步硝化-厌氧氨氧化-反硝化,且在一定程度上提高脱氮效率。     

Output feedback controller for polytopic systems exploiting the direct searching of the design space

This paper deals with the problem of designing a robust static output feedback controller for polytopic systems. The current research that tackled this problem is mainly based on LMI method, which is conservative by nature. In this paper, a novel approach is proposed, which considers the design space of the controller parameters and iteratively partitions the space to small simplexes. Then, by assessing the stability in each simplex, the solution space for design parameters is directly determined. It has been theoretically proved that, if there exists a feasible solution in the design space, the algorithm can find it. To validate the result of the proposed approach, comparative simulation examples are given to illustrate the performance of the design methodology as compared to those of previous approaches.     

Transmission system restoration with co-optimization of repairs,load pickups,and generation dispatch

This paper studies the restoration of a transmission system after a significant disruption such as a natural disaster. It considers the co-optimization of repairs, load pickups, and generation dispatch to produce a sequencing of the repairs that minimizes the size of the blackout over time. The core of this process is a Restoration Ordering Problem (ROP), a non-convex mixed-integer nonlinear program that is outside the capabilities of existing solver technologies. To address this computational barrier, the paper examines two approximations of the power flow equations: The DC model and the recently proposed LPAC model. Systematic, large-scale testing indicates that the DC model is not sufficiently accurate for solving the ROP. In contrast, the LPAC power flow model, which captures line losses, reactive power, and voltage magnitudes, is sufficiently accurate to obtain restoration plans that can be converted into AC-feasible power flows. An experimental study also suggests that the LPAC model provides a robust and appealing tradeoff between accuracy and computational performance for solving the ROP.     

Analysis of adhesively bonded CFRE composite scarf joints modified with MWCNTs

The main objective of the present work is to improve the performance of bonded joints in carbon fiber composite structures through introducing Multi-Walled Carbon Nanotubes (MWCNTs) into Epocast 50-A1/946 epoxy, which was primarily developed for joining and repairing of composite aircraft structures. Results from tension characterizations of structural adhesive joints (SAJs) with different scarf angles (5–45°) showed improvement up to 40% compared to neat epoxy (NE)–SAJs. Special attention was considered to investigate the performance of SAJs with 5° scarf angle under different environments. The tensile strength and stiffness of both NE-SAJs and MWCNT/E-SAJs were dramatically decreased at elevated temperature. Water absorption showed a marginal drop of about 2.0% in the tensile strength of the moist SAJs compared to the dry one. Cracks initiation and propagation were detected effectively using instrumented-SAJs with eight strain gauges. The experimental results agree well with the predicted using three-dimensional finite element analysis model.     

关于新疆热电厂职业危害分析与讨论

对比不同热电厂企业工人接触职业危害因素情况,分析原因,为在建或已建热电厂提供职业危害因素预防措施,降低企业由于设计、施工或管理方面原因造成后期运行过程中职业危害接触超标情况的发生。根据我室历年对新疆地区热电厂职业危害因素检测结果与评价报告的比较,找出不同热电厂职业病危害因素的共性及异性,分析不同设备、工艺及管理方式不同所造成职业危害因素检测结果的差异及原因。建议优化厂区工艺及土建设计;优化设备选型及原料选择运用现代化的管理手段,加强职业卫生管理体系宣贯的有效运作。     

Generic mathematical programming formulation and solution for computer-aided molecular design

This short communication presents a generic mathematical programming formulation for computer-aided molecular design (CAMD). A given CAMD problem, based on target properties, is formulated as a mixed integer linear/non-linear program (MILP/MINLP). The mathematical programming model presented here, which is formulated as an MILP/MINLP problem, considers first-order and second-order molecular groups for molecular structure representation and property estimation. It is shown that various CAMD problems can be formulated and solved through this model.     

喷淋液滴在空气环境下的运动特性

本文以喷淋液滴在空气环境下运动特性为工程背景，建立单个液滴在常温、常压空气环境中的动量方程，分析液滴沉降特性、追赶特性及运动轨迹行为。计算结果表明，不同喷淋液滴初始条件下，短时间内存在重力大于曳力和重力小于曳力两种情况，但最终减速液滴均会达到受力平衡状态；液滴离开喷淋头后，垂向位移均迅速增大，液滴粒径越大、初始速度越大，垂向位移增长的速率也越大，达到相同位移的用时越短；液滴尺寸、初始速度相差越大，液滴追赶所用的时间越短，追赶位移越小，液滴尺寸、初始速度越接近，液滴追赶所用的时间越长，追赶位移越大；液滴初始速度越大、初始直径越大、喷射角度越大，横向速度消失越慢，达到的横向位移越大，喷射液滴覆盖的面积也越大。计算结果有助于优化工程实际中喷淋系统的设计与布置。     

Robust predictive extended state observer for a class of nonlinear systems with time-varying input delay

ABSTRACT

This paper deals with asymptotic stabilisation of a class of nonlinear input-delayed systems via dynamic output feedback in the presence of disturbances. The proposed strategy has the structure of an observer-based control law, in which the observer estimates and predicts both the plant state and the external disturbance. A nominal delay value is assumed to be known and stability conditions in terms of linear matrix inequalities are derived for fast-varying delay uncertainties. Asymptotic stability is achieved if the disturbance or the time delay is constant. The controller design problem is also addressed and a numerical example with an unstable system is provided to illustrate the usefulness of the proposed strategy.