二次盐水及离子膜电解工序常见问题简析

介绍了二次盐水及离子膜电解工序的主要设备和流程,对二次盐水及离子膜电解工序运行中出现的问题进行了分析,并提出了解决措施。     

M8011H16铝合金防盗盖板生产工艺研究

研究了元素含量变化对8011铝合金防盗盖板综合性能的影响，在8011合金中改变Cu、Mn元素含量后可提高防盗盖板的强度，同时研究了烘烤处理后的强度变化问题。本文研究出了8011铝合金防盗盖板新的生产工艺制度。     

混联法氧化铝生产中熟料窑节能降耗的研究

通过对熟料窑的热工综合测试，分析了熟料窑的能耗组成和影响能耗的关键因素，总结了技术改造带来的经济效益和生产中存在的问题，提出了进一步挖潜降耗的措施。     

NaAlO_2-Al_2(SO_4)_3法制备拟薄水铝石成胶机理的研究

研究了拟薄水铝石和三水氧化铝的生成机理。考察了成胶pH、成胶温度对生成物类型的影响,在此基础上确定了NaAlO2溶液和Al2(SO4)3溶液成胶过程中完全中和时的临界体积比Ψ/Ψ0,在成胶过程中,当Ψ/Ψ0≤1时,NaAlO2溶液与Al2(SO4)3溶液发生中和反应生成拟薄水铝石和/或碱式硫酸铝;当Ψ/Ψ0>1时,过量的NaAlO2溶液发生自发水解反应,生成三水氧化铝。     

钕电解阳极过电位的测定

用慢扫描示波法测定了钕电解的阳极过电位 .考察了温度、阳极电流密度、Nd2 O3添加量、电解质组成等因素对阳极过电位的影响 ,探讨了降低阳极过电位的可能途径 .结果表明 ,阳极过电位随阳极电流密度的增加而增大 ,随温度的升高而减小 ,一定范围内 ,阳极过电位与阳极电流密度的对数呈线性关系 ,满足塔菲尔方程 ;电解质中LiF和Nd2 O3浓度增加 ,阳极过电位降低 ;适当控制阳极电流密度、升高温度、增加电解质中LiF和Nd2 O3的浓度并尽可能减小极间距 ,均有利于降低阳极过电位     

参数设计法在铝电解电容器设计中的应用探讨

论述了参数设计法在铝电解电容器设计开发阶段的应用。文中阐明了铝电解电容器的主要质量特性(损耗因子、电容量)及芯包外径的参数设计原理,并建立了归一化函数作为优选设计方案的判据。实例证明在铝电解电容器的设计过程中应用参数设计法以减小产品质量特性变异是有效的。     

Failure of a stationary pump engine piston

Piston failures are not a common occurrence, but they do occur, and failure is usually associated with fatigue crack growth. Most failures initiate at the gudgeon pin hole or in the skirt of the piston. Occasionally they fail elsewhere. In the example covered in this paper, failure initiated in the crown and progressed down to the gudgeon pin before final failure occurred. This paper outlines the cause and mode of failure and shows that small metallurgical discontinuities can contribute to these failures under the right circumstances.     

铝型材推弯工艺

通过铝型材圆环的推弯实验,研究了推弯工艺原理、变形过程,结合有限元模拟得到了和实验结果相吻合的型材厚度分布、成形零件卸载回弹后的曲率半径及型材截面畸变.结果表明:推弯零件曲率及截面畸变一致性高,成形模具结构简单且便于调整,数值模拟可以用于推弯工艺的优化分析.     

Structure of rapidly solidified aluminum alloys

This paper is a summary of an extensive research program carried out by the authors on the structure of rapidly solidified aluminum alloys; and a comparison with the work of others also involved in this field. The paper discusses the changes in the dendritic and non-dendritic structure of the matrix at cooling rates from 10^–3 to 10¹⁰ K/s and discusses the hetergeneity of the structure caused by interdendritic-segretion during solidification.     

Preparation of Ultra—fine Aluminum Nitride in Thermal Plasma

Ultra-fine aluminum nitride has been synthesized by the evaporation of aluminum powder at atmospheric-pressure nitrogen plasma in a hot-wall reactor.The average size of aluminum nitride particle is 0.11μm measured by scanning electric mirror(SEM),and the purity is at least over90% evaluated by X-Ray diffraction(XRD).The conversion of Al powder to aluminum nitride is strongly depended on the injection of NH3.Typical experimental parameters such as the feed rate of raw material,the flow rate of ammonia and the position of injecting aluminum powder into the reactor are given.