Unique CNTs-chained Li4Ti5O12 nanoparticles as excellent high rate anode materials for Li-ion capacitors

Composite anode materials with a unique architecture of carbon nanotubes (CNTs)-chained spinel lithium titanate (Li₄Ti₅O₁₂, LTO) nanoparticles are prepared for lithium ion capacitors (LICs). The CNTs networks derived from commercial conductive slurry not only bring out a steric hindrance effect to restrict the growth of Li₄Ti₅O₁₂ particles but greatly enhance the electronic conductivity of the CNTs/LTO composites, both have contributed to the excellent rate capability and cycle stability. The capacity retention at 30 C (1 C = 175 mA g^?1) is as high as 89.7% of that at 0.2 C with a CNTs content of 11 wt%. Meanwhile, there is not any capacity degradation after 500 cycles at 5 C. The LIC assembled with activated carbon (AC) cathode and such a CNTs/LTO composite anode displays excellent energy storage properties, including a high energy density of 35 Wh kg^?1 at 7434 W kg^?1, and a high capacity retention of 87.8% after 2200 cycles at 1 A g^?1. These electrochemical performances outperform the reported data achieved on other LTO anode-based LICs. Considering the facile and scalable preparation process proposed herein, the CNTs/LTO composites can be very potential anode materials for hybrid capacitors towards high power-energy outputs.     

DC conductivity and AC impedance of Mn doped magnesia alumina spinel (MgAl2-2xMn2xO4) over a large temperature range

MgAl_2-2xMn_2xO₄ (MAMO) with x = 0-0.12 was synthesized in a single-phase form by solid-state reaction. XRD analysis showed that the samples had the cubic center structure of the Fd-3 m space group. Electrical properties of the samples were studied over the temperature range of 300 K∼1073 K. The results showed that the DC conductivity (σ_DC) increased from 10⁻¹¹S/cm at 300 K (MAMO, x = 0) to 10^-3S/cm at 1073 K (MAMO, x = 0.12). The equivalent circuit of the complex impedance spectra suggested that the relaxation of charge carriers was of non-Debye type. The conduction was mainly caused by grain boundaries and the capacitance was mainly attributed to polarization. The complex permittivity values (ε’ and ε’’) were increased by two orders of magnitude with the increase in Mn content and temperature over the measured frequency range (1 Hz-1 MHz). Therefore, doping with Mn could be applied to modify the electrical properties of MAMO at high temperature.     

亲水作用色谱-串联质谱法测定动物源运动食品中3种氨基糖苷类抗生素的残留量

该研究建立了一种亲水交互作用色谱-串联质谱（HILIC-MS/MS）法测定动物源运动食品中潮霉素B、新霉素、安普霉素3种氨基糖苷类抗生素残留量的方法。结果表明，样品经Sielc Obelisc R柱分离，采用0.1%甲酸水溶液-乙腈梯度洗脱，可以实现3种目标物组分的分离。在此条件下，3种氨基糖苷类抗生素在5～500 ng/mL的质量浓度范围内线性关系良好，相关系数R2为0.999 5～0.999 9，检出限均为15 μg/kg，定量限均为50 μg/kg，保留时间的日间和日内相对标准偏差（RSD）分别为3.5%～7.9%和3.5%～4.1%，峰面积的日间和日内RSD分别为3.6%～7.4%和3.2%～3.9%，加标回收率为85.7%～93.6%，回收率试验结果的RSD为3.1%～5.2%。该方法可以满足动物源运动食品中3种氨基糖苷类抗生素的检测需求。     

Rapid screening of DON contamination in whole wheat meals by Vis/NIR spectroscopy and computer vision coupling technology

This work intends to develop an online experimental system for screening of deoxynivalenol (DON) contamination in whole wheat meals by visible/near-infrared (Vis/NIR) spectroscopy and computer vision coupling technology. Spectral and image information of samples with various DON levels was collected at speed of 0.15 m s⁻¹ on a conveyor belt. The two-type data were then integrated and subjected to chemometric analysis. Discriminant analysis showed that samples could be classified by setting 1000 μg kg⁻¹ as the cut-off value. The best correct classified rate obtained in prediction was 93.55% based on fusion of spectral and image features, with reduced prediction uncertainty as compared to single feature. However, quantification of DON by quantitative analysis was not successful due to poor model performance. These results indicate that, although not accurate enough to provide conclusive result, this coupling technology could be adopted for rapid screening of DON contamination in cereals and feeds during processing.     

Finite element analysis of fracture behavior in ceramics: Competition between artificial notch and internal defects under three-point bending

Evaluation of the nonlinear relationship between the surface defect size and fracture strength of ceramics is important for engineering applications. In this study, we aim to predict the apparent nonlinear relationship between the defect size and fracture strength of single-edge notched beams (SENBs) using the finite element method. Specifically, we applied the methodology for predicting fracture strength from microstructure distribution data (relative density, pore size, aspect ratio, and grain size) to a finite element analysis (FEA) model in which the shape and size of the initial defects are defined at notch locations. By reproducing the apparent nonlinearity caused by the competition between the surface and internal defects within the framework of linear elastic fracture mechanics, the effectiveness of the FEA methodology for the evaluation of strength scatter and allowable crack size in ceramics was demonstrated.     

杭州湾南岸滩涂沉积物中HCHs与DDTs污染特征分析

摘 要：目的 了解六六六（hexachlorocyclohexanes,HCHs）与滴滴涕(dichloro diphenyl trichloroethanes,DDTs)在杭州湾南岸滩涂沉积物中的污染现状。方法 于2018年4月，采集杭州湾南岸地区4个采样点不同深度（0~80 cm）滩涂沉积物，利用气相色谱-串联质谱法（gas chromatography tandem mass spectrometry, GC-MS/MS）测定了该区域中HCHs与DDTs的含量，对其分布规律进行分析，使用共识沉积物质量基准法对其生态学风险进行了评估。结果 所有样品中均检出，HCHs与DDTs含量分别为4.20~6.24 μg/kg与3.37~4.73 μg/kg，主要以β-HCH、δ-HCH以及DDE为主，其污染主要来源于历史性工业品，整体污染处于较低水平；20.3%的沉积物样品中DDEs含量以及28.1%的样品DDTs总量介于阈值效应浓度(threshold concentration, TECs) 和可能效应浓度(probable effect concentration, PECs)之间。结论 杭州湾南岸沉积物中HCHs与DDTs的污染处于较低水平，具有较小的生态学风险。     

Characterization of anisotropic gas permeability and thermomechanical properties of highly textured porous alumina

Porous alumina with a highly textured microstructure was fabricated by pulse electric current sintering (PECS) using alumina platelets. Highly oriented porous alumina with a porosity of 3%–50% was obtained by a pressure-controlled method of PECS. The properties of the highly textured porous alumina were measured in two directions. The nitrogen gas permeance and thermal conductivity at room temperature were higher in the direction along the platelet length due to the higher continuity of pores and the connectivity of alumina platelets, respectively. The anisotropy of the thermal conductivity at room temperature was investigated and explained by the effect of grain size of platelets as well as morphology and orientation of pores. The bending strength was higher with the loading direction along the platelet thickness. The thermal shock strength was clearly different in the two directions. The difference in the thermal shock strength was investigated by the measurement of properties and thermal stress analysis.     

APP软件性能效率研究

性能效率是APP软件的重要质量属性，但目前缺乏APP软件性能效率的通用模型。分析了APP软件的性能特征，基于ISO/IEC 25010标准提出了APP软件的性能效率模型，定义了APP软件性能效率的子特性和度量指标。基于提出的APP软件性能效率模型，通过实验对APP软件的性能效率进行了度量及相关分析。     

Combustion synthesis of AlN doped with carbon and oxygen

Carbon-and-oxygen-doped AlN specimens were prepared by combustion synthesis using Al, graphite, and AlN. Graphite addition changed the product color from white to blue. By XRD, the lattice constant increased slightly with increasing carbon content. Blue AlN powder was synthesized with a molar ratio of the diluent AlN of 0.2-0.5 with a fixed graphite content of 0.05. At an AlN molar ratio exceeding 0.6, carbon was not successfully incorporated due to the lower reaction temperature. Calcination at 800°C in air removed residual graphite without changing the crystal structure or product color. Oxygen, nitrogen, and carbon analyses revealed that blue AlN powders contained 0.45-0.54 mass% carbon and 1.4-1.6 mass% oxygen, while the undoped AlN contained 0.021 mass% carbon and 0.94 mass% oxygen. The origin of the white-to-blue color change was investigated via reflection measurements. Blue AlN exhibits an absorption peak at 634 nm (1.96 eV). From first-principles electronic structure calculations, the C-doped AlN and carbon-and-oxygen-doped AlN with a 1:1 ratio could be classified as p-type, whereas the O-doped AlN and 1:3 carbon-and-oxygen-doped AlN were n-type. One reason for the absorption peak at 634 nm may be a transition from the conduction band to an upper unoccupied state. These results suggest the possible control of optical and electronic properties of AlN via carbon-and-oxygen doping.     

Rational Designs for Lithium-Sulfur Batteries with Low Electrolyte/Sulfur Ratio

Lithium-sulfur batteries (LSBs) are considered a promising next-generation energy storage device owing to their high theoretical energy density. However, their overall performance is limited by several critical issues such as lithium polysulfide (PS) shuttles, low sulfur utilization, and unstable Li metal anodes. Despite recent huge progress, the electrolyte/sulfur ratio (E/S) used is usually very high (≥20 µL mg⁻¹), which greatly reduces the practical energy density of devices. To push forward LSBs from the lab to the industry, considerable attention is devoted to reducing E/S while ensuring the electrochemical performance. To date, however, few reviews have comprehensively elucidated the possible strategies to achieve that purpose. In this review, recent advances in low E/S cathodes and anodes based on the issues resulting from low E/S and the corresponding solutions are summarized. These will be beneficial for a systematic understanding of the rational design ideas and research trends of low E/S LSBs. In particular, three strategies are proposed for cathodes: preventing PS formation/aggregation to avoid inadequate dissolution, designing multifunctional macroporous networks to address incomplete infiltration, and utilizing an imprison strategy to relieve the adsorption dependence on specific surface area. Finally, the challenges and future prospects for low E/S LSBs are discussed.