ZrO_2掺杂对SACM高强度玻璃纤维结构性能的影响

以SACM(SiO_2-Al2O3-CaO-MgO)高强玻璃纤维体系为基础,掺杂不同质量分数的ZrO_2,研究其玻璃的结构和性能。结果表明:在SACM高强玻璃纤维体系中,玻璃纤维直径越小,其拉伸强度和断裂伸长率越大;随着ZrO_2质量分数的增加,玻璃纤维的拉伸强度和断裂伸长率均呈现先增大后减小的趋势;玻璃样品的质量损失率则呈现先减小后增大的趋势,而玻璃转变温度和软化温度在ZrO_2质量分数为1%时,出现极大值。     

电磁连铸和微合金化对5356铝合金组织性能的影响

研究了不同电源功率、拉坯速率和冷却水量等参数以及微量Sc元素对5356铝合金组织和性能的影响。结果表明,在电源功率10 k W,拉坯速率8 cm/min,冷却水量1.7 m3/h的工艺条件下,5356铝合金具有最优的表面和内部质量以及综合力学性能,抗拉强度、伸长率分别可达310.0 MPa和16.3%,且铸锭表面无明显铸造缺陷,边部组织基本为等轴晶,心部组织呈破碎枝晶形态,第二相分布均匀。5356铝合金合理的均匀化处理工艺参数为440℃,30 h,空冷,均匀化处理后合金元素Mg的微观偏析基本消除,在晶界连续分布的Al8Mg5相明显回溶。微量的Sc元素显著提高5356铝合金的强度和塑性。实验证明,5356Al+0.4%Sc(质量分数)合金晶粒明显细化,第二相数量减少,抗拉强度和伸长率达330.0 MPa和29.0%,分别提高6.5%和77.9%。     

α-Al2 O3微粒对铸造Al-Si合金微弧氧化膜耐蚀性的影响

目的通过共生沉积技术将α-Al2O3微粒引入到铸造Al-Si合金微弧氧化膜中,并研究其对膜层耐蚀性的影响。方法利用SEM和XRD分析α-Al2O3微粒对微弧氧化膜微观结构及成分的影响。通过极化曲线、交流阻抗谱及中性盐雾试验评价膜层的耐蚀性。结果α-Al2O3微粒复合改变了微弧氧化膜的组成及结构。微弧氧化膜呈双层结构,表面存在大量微孔,主要组成为γ-Al2O3;加入α-Al2O3微粒后,微弧氧化复合膜的表面微孔大幅减少,致密度提高,且膜层中α-Al2O3相增多。此外,α-Al2O3微粒复合改善了微弧氧化膜的耐蚀性。微弧氧化膜在质量分数为3.5%的Na Cl溶液中的自腐蚀电流密度约为1.476×10-5A/cm2,多孔层电阻Rp及阻挡层电阻Rb分别为0.259 kΩ·cm2及69.18 kΩ·cm2,耐盐雾试验时间为1200 h。加入α-Al2O3微粒后,微弧氧化复合膜的自腐蚀电流密度仅为微弧氧化膜层的28%,Rp大幅增加至274.5 kΩ·cm2,且Rb也上升了一个数量级,耐盐雾试验时间可达1440 h。结论α-Al2O3微粒的引入可以大幅提高铸造Al-Si合金微弧氧化膜的耐蚀性。     

Hydrothermal synthesis of boehmites with various particle sizes and transition to α-Al2O3 powders by calcination

Boehmite powders with various particle sizes have been prepared by hydrothermal method and the α-Al2 O3 powders yielded after subsequent calcination have been studied. Dispersive crystalline boehmite powders of 30-100 nm, 0.4-0. 6μm and 1μm in size were obtained respectively by changing the hydrothermal precursors and the pH value of hydrothermal slurry. Calcination of boehmite powders of 30-100 nm at 1250℃ for 1h resulted in the formation of single-phase α-Al2O3,and the products consisted of vermicular particles. The boehmite powders of 0.4-0.6μm were also fully converted to α-Al2O3 at 1250℃, and the products consisted of plate-like particles with the same size of 0. 4-0. 6μm. The boehmite powders of 1μm calcined at 1350℃ for 2h were still composed of a little proportions of transition aluminas besides α-Al2 O3, and the particles sintered severely. The reaction processes for the formation of crystalline boehmites under hydrothermal conditions and α-Al2O3 powders during calcination have been discussed.     

Compositional tailoring effect on crystal structure,mechanical and thermal properties of γ-AlON transparent ceramics

In view of the practical application of γ-AlON as a promising transparent structural ceramic, in-depth insight into its mechanical and thermal properties is essential. The solid-state MAS NMR technique was combined with XRD Rietveld refinement to confirm the crystal structure of Al_(8+x)/3O_4-xN_x (x = 0.299–0.575). These structural parameters were further applied to predict hardness and elastic properties based on theoretical exploration, which are in good agreement with the experimental values. A slight enhancement of mechanical properties with increasing nitrogen concentration is attributed to the stronger chemical bond in octahedra. The experimental thermal conductivity of γ-AlON transparent ceramics was improved slightly with the rise of x in the temperature range from 298 K to 1074 K. The intrinsic lattice thermal conductivity was determined by eliminating the extrinsic phonon scattering as well as the thermal radiation. The reason for the discrepancy between experimental and intrinsic thermal conductivity was revealed. The present methods provided powerful and accessible guidelines in optimizing the mechanical and thermal properties of oxynitride materials.     

用于珠光颜料的片状氧化铝制备

采用熔融盐法制备片状α-Al2O3,研究了硫酸盐、煅烧温度、添加剂(磷酸盐、二氧化钛)对片状α-Al2O3晶体形貌的影响。当氢氧化铝凝胶煅烧温度为900℃时,没加硫酸盐分解所得的氧化铝晶相为κ-Al2O3晶相,而加入硫酸盐的氧化铝晶相为α-Al2O3晶相,熔融盐降低了片状α-Al2O3的形成温度,促进κ-Al2O3向α-Al2O3晶型转变。煅烧温度由900℃上升到1200℃时,片状α-Al2O3的团聚程度降低,颗粒尺寸分布更加均匀。当煅烧温度在1200℃下、磷酸盐添加量为3%、二氧化钛添加量为2%时,所制得片状氧化铝分散均匀,径厚比较大,片状氧化铝平均粒径为5.225μm、厚度约400-500 nm。     

气相色谱法测定γ-戊内酯的方法学研究

采用内标法进行了γ-戊内酯测定的气相色谱方法学研究。采用十二烷为内标物,对气相色谱分析γ-戊内酯的专属性、精密度、准确度、检测限等进行了验证。结果表明,气相色谱检测γ-戊内酯具有良好的线性（γ-戊内酯和内标物十二烷的浓度比（g/g）在0.25～2.5之间成线性,相关系数R2=0.9984）,重复测定相对标准偏差小于5.0%,加标回收率为99.5%~104.6%。实验表明内标气相色谱法可以用于γ-戊内酯的定量分析。     

Chain stiffness and chain conformation of poly(α-methylene-γ-butyrolactone) in dilute solutions

The chain stiffness and local chain conformation of atactic poly(α-methylene-γ-butyrolactone) (PMBL), which is a side chain cyclic structural analog of poly(methyl methacrylate) (PMMA), with a weight-average molecular weight (M_w) ranging from 2.8 × 10³ to 2.6 × 10⁶ in N,N-dimethylformamide (DMF) and γ-butyrolactone (GBL) were characterized by size exclusion chromatography with a multi-angle light-scattering detector (SEC-MALS) and synchrotron radiation small-angle X-ray scattering (SAXS). Based on the Kratky-Porod worm-like chain model, the scattering functions and the M_w dependence of z-average root-mean-square radius of gyration <S²>_z^1/2 yielded the Kuhn segment lengths λ⁻¹, the diameter of the PMBL chains d, and the excluded-volume strengths in DMF and GBL. The local conformation of atactic PMBL in DMF and GBL were slightly larger than those of atactic PMMA, due to the presence of the conformationally rigid lactone ring structure.     

枯草芽孢杆菌Dg5041液体发酵生产γ-聚谷氨酸

以枯草芽孢杆菌Dg5041为生产菌,对其摇瓶发酵生产γ–聚谷氨酸(γ-PGA)的工艺进行研究,通过单因素实验和正交实验获得了该菌的优化培养条件。优化的培养基组成为:葡萄糖35 g/L,酵母膏10 g/L,谷氨酸钠40 g/L,MgSO41.0 g/L,K2HPO4 2.0 g/L,MnSO40.5 g/L,pH 7.0,250 mL锥形瓶装液量50 mL。菌种在37℃,120 r/min培养24 h加入5%NaCl后继续培养24 h,γ-PGA产量达到18.54 g/L。研究结果表明,枯草芽孢杆菌Dg5041是一株很有潜力的γ-PGA高产菌。     

Ce_(0.7)Zr_(0.3)/γ-Al_2O_3纳米固溶体的制备及其结构

以氯氧化锆、硝酸铈、硝酸铝为原料,按n(Ce)∶n(Zr)=0.7∶0.3的比例,采用化学共沉淀法与有机物共沸蒸馏法,将CeO2、ZrO2分散到γ-Al2O3表面上使其形成Ce0.7Zr0.3O2/γ-Al23固溶体。用XRD考察纳米固溶体在不同温度下焙烧后的相结构。结果表明:Ce0.7Zr0.3O2/γ-Al2O3纳米固溶体为立方晶型,且随着焙烧温度的升高,样品的衍射峰依次变强,峰宽变窄。