7075铝合金热变形连接接头的组织与性能

应用Gleeble-3500热模拟机对7075铝合金进行了热变形连接试验,利用金相显微镜和扫描电镜对不同温度和保温时间的接头界面组织进行了观察和分析,并对接头进行了拉伸性能测试。结果表明:当连接温度为460 ℃,保温时间为24 h时,对界面进行EDS分析,界面处已经没有氧化物的偏聚,此时的力学性能最佳,抗拉强度达到444 MPa,屈服强度为265 MPa。     

Microstructure,mechanical properties and bio-corrosion properties of Mg-HA bionanocomposites fabricated by a novel severe plastic deformation process

This research investigates the alterations in microstructure, mechanical properties, and corrosion behavior of binary magnesium-hydroxyapatite bionanocomposites with 2, 5, and 10 wt%HA. By mixing Mg and HA powders with different percentages of HA contents, a combined method of cyclic extrusion compression (CEC), equal channel angular pressing (ECAP) and conventional extrusion were employed to consolidate the mixture of powders. All composites were examined. The results indicate that the addition of hydroxyapatite to magnesium improves the mechanical properties, but these properties are deteriorated with the hydroxyapatite content of over 5 wt%. The corrosion behavior of the composites was examined by immersion test, mass loss and polarization tests in Hank’s solution. The results indicate that Mg-5HA exhibits the best corrosion resistance and the corrosion rate increases when the HA content rises to more than 5 wt%. In addition, the specimen produced through the proposed method in this work indicates better corrosion resistance in comparison with cast and extruded pure Mg.     

强变形工艺对2519A铝合金组织与性能的影响

通过硬度测试、拉伸性能测试、透射电镜观察等分析手段研究了不同强变形工艺下2519A铝合金的力学性能与微观组织。结果表明,经50%的冷轧变形和165 ℃人工时效后,2519A合金的力学性能明显提高,其抗拉强度、屈服强度和伸长率分别为522 MPa、468 MPa和8.5%。而在冷变形前添加165 ℃×2 h预时效处理,合金的力学性能进一步提高,其抗拉强度、屈服强度和伸长率分别达到535 MPa、497 MPa和8%。预时效处理可以提高合金中θ′相的密度,使析出相分布更加均匀,有助于提高合金的力学性能。     

Multicellular Tumor Spheroids (MCTS) as a 3D In Vitro Evaluation Tool of Nanoparticles

Multicellular tumor spheroid models (MCTS) are often coined as 3D in vitro models that can mimic the microenvironment of tissues. MCTS have gained increasing interest in the nano‐biotechnology field as they can provide easily accessible information on the performance of nanoparticles without using animal models. Considering that many countries have put restrictions on animals testing, which will only tighten in the future as seen by the recent developments in the Netherlands, 3D models will become an even more valuable tool. Here, an overview on MCTS is provided, focusing on their use in cancer research as most nanoparticles are tested in MCTS for treatment of primary tumors. Thereafter, various types of nanoparticles—from self‐assembled block copolymers to inorganic nanoparticles, are discussed. A range of physicochemical parameters including the size, shape, surface chemistry, ligands attachment, stability, and stiffness are found to influence nanoparticles in MCTS. Some of these studies are complemented by animal studies confirming that lessons from MCTS can in part predict the behaviour in vivo. In summary, MCTS are suitable models to gain additional information on nanoparticles. While not being able to replace in vivo studies, they can bridge the gap between traditional 2D in vitro studies and in vivo models.     

Waves in generalized thermo-viscoelastic infinite continuum with cylindrical cavity due to three-phase-lag time-nonlocal heat transfer

Abstract

Generalized thermoelastic interactions due to three-phase-lag time-nonlocal heat transfer in a Kelvin-Voigt type infinitely extended visco-thermoelastic continuum with cylindrical cavity has been investigated. The two-temperature generalized thermoelasticity theory has also been taken into account. The problem has been solved in the domain of Laplace on the assumption that the surface of the cavity is free from traction and is subjected to a smooth and time-dependent-heating effect. Laplace inversion of the transformed solutions has been carried out numerically. The obtained numerical data for different considerations are plotted in graphs to study the effects of time-nonlocal parameter, two-temperature parameter and visco-thermoelastic relaxation parameter on different thermoelastic quantities of physical interest.     

Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component

This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness.     

Flame Front Deformation Instabilities of Filtration Combustion for Initial Thermal Perturbation

The flame front deformation instability of low-velocity filtration combustion within an inert packed bed is studied based on the initial preheating non-uniformity. Based on the experimental phenomena, an initial thermal perturbation model is numerically proposed so as to predict the deformation behaviors of the flame front instabilities. The numerical prediction indicates that the assumption of an initial thermal perturbation is a feasible explanation as the cause of the flame front inclination instability. As the initial thermal perturbation increases, the phenomena of the flame front break and shrinking instabilities could easily occur at high filtration velocity or low equivalence ratio. Moreover, the evolutions of the flame front break rate and the shrinking rate are quantitatively analyzed.     

随钻扩眼工具及技术研究

基于随钻扩眼技术优势的分析，研究了机械式、液压式和偏心式随钻扩眼工具执行机构和扩眼总成的机构原理，并介绍了国内所开展的相关研究。文章提出应加强现有工具的适应性和匹配性研究，发掘各类工具的优势。优化执行机构、扩眼总成和水力机构、重视底部钻具组合力学特性的分析是今后发展和完善随钻扩眼工具及技术的几个重要内容。实践表明，随钻扩眼技术在处理井下复杂情况、降低钻井综合成本、提高钻井速度、提高建井质量和安全性等方面具有显著的优势，随钻扩眼工具也正逐渐成为一种重要的石油钻井配套工具。     

最大塑性功原理在烧结体上限分析中的应用

最大塑性功原理又称第二塑性变分原理，在致密体塑性变形分析叶l是运用能量法进行变形力能计算的基础。本文从分析Drucker公设的亢要条件出发，证明了烧结体塑性变形最大塑性功原理的存在，片在该原理的荩础卜，推导出塑性变形的上限功率表达式，并以平面挤压条件下的上限法应用作为实例加以说明。     

The effect of ionic cross-links on the deformation behavior of homoblends made of poly(styrene-co-styrenesulfonic acid) and poly(styrene-co-4-vinylpyridine)

Deformation behavior of stoichiometric blends made from poly(styrene-co-styrenesulfonic acid) (SPS) and poly(styrene-co-4-vinylpyridine) (SVP) was investigated by TEM observation of strained thin films. An FTIR investigation revealed that ionic cross-links were formed between the component polymers upon blending due to intermolecular ion-ion interactions, which arose from proton transfer from sulfonic acid groups to pyridine groups. TEM observations indicate that the deformation mode of the blends changed from crazing only to crazing plus shear deformation, with the shear contribution becoming larger, as the ion content in the blends increased. Such changes in deformation mode can be understood as arising from an increase in the ‘effective’ strand density due to the formation of ionic cross-links upon blending. It was also found that the ionic cross-links via pyridinium cation/sulfonate anion ion pairs were more effective in inducing the transition of deformation mode than ionic cross-links via -SO₃⁻/Na⁺ or -SO₃⁻/Ca²⁺ ion pairs.