Thermal imaging of time-varying longitudinal defects in the internal coating of a tube

We deal with the mathematical model of the incremental degradation of the internal coating (e.g. a polymeric material) of a metallic pipe in which a fluid flows relatively fast. The fluid drags solid impurities so that longitudinal scratches, inaccessible to any direct inspection procedure, are produced on the coating. Time evolution of this kind of defects can be reconstructed from the knowledge of a sequence of temperature maps of the external surface. The time-varying orthogonal section of this damaged interface is determined as a function of time and polar angle through the identification of a suitable effective heat transfer coefficient by means of Thin Plate Approximation.     

某矿快速掘进最优炮孔间距的选择

山西某矿5308底抽巷在掘进过程中速度慢、效率低，直接影响工作面的瓦斯抽采，为了改善上述情形，对炮孔间距进行研究。通过使用ANSYS软件对不同炮孔间距下快速掘进效果的模拟分析，并经现场验证，得出了适应该矿的最佳炮孔间距。结果表明：炮孔间距为500 mm时，爆破产生裂隙发育范围和岩石损伤区域都最大，快速掘进的效果最好。     

结合优化支持向量机与K-means++的工控系统入侵检测方法

针对工业控制系统传统单一检测算法模型对不同攻击类型检测率和检测速度不佳的问题，提出一种优化支持向量机和K-means++算法结合的入侵检测模型。首先利用主成分分析法（PCA）对原始数据集进行预处理，消除其相关性；其次在粒子群优化（PSO）算法的基础上加入自适应变异过程避免在训练的过程中陷入局部最优解；然后利用自适应变异粒子群优化（AMPSO）算法优化支持向量机的核函数和惩罚参数；最后利用密度中心法改进K-means算法与优化后的支持向量机组合成入侵检测模型，从而实现工业控制系统的异常检测。实验结果表明，所提方法在检测速度和对各类攻击的检测率上得到明显提升。     

Simulation Analysis of the Heat Transfer Performance of an N-type Microchannel Heat Exchanger

A microchannel heat exchanger with a triangular wave and symmetrical triangular wave structure was proposed in this paper. In addition, a new N-type microchannel heat exchanger was developed to balance the heat transfer performance and pressure drop. The relationship between different configurations of the N structure of the microchannel and the heat transfer performance was analyzed. The results showed that, at a high inlet flow rate, the symmetrical triangular wave microchannel had the best heat transfer performance, followed by the triangular wave microchannel and the straight channel. At the same flow rate, the degree of disturbance of the fluid was highest in the symmetrical N-structure microchannel, and an excellent heat transfer effect was observed.     

发夹式换热器管束流致振动数值模拟研究

运用计算流体力学方法,采用ANSYS CFX软件对发夹式换热器的壳侧流场进行了三维数值模拟。流场计算中采用多孔介质模型对管束区域进行简化,分析了壳侧流场的速度分布,结果表明:直管段部分的流体湍流强度大于弯管段,且外层管束所在区域为高流速区,受流体冲刷严重。结合流场信息,通过功率谱生成随机激振力,采用ABAQUS软件模拟计算了湍流激振下管束的振动响应,结果显示管束的面外均方根位移远大于面内位移,且弯管部分的振动位移最大。该研究结果可为发夹式换热器的性能分析和优化设计提供参考和依据。     

Design of disturbance observer based on adaptive-neural control for large-scale time-delay systems in the presence of actuator fault and unknown dead zone

This article presents an adaptive neural compensation scheme for a class of large-scale time delay nonlinear systems in the presence of unknown dead zone, external disturbances, and actuator faults. In this article, the quadratic Lyapunov–Krasovskii functionals are introduced to tackle the system delays. The unknown functions of the system are estimated by using radial basis function neural networks. Furthermore, a disturbance observer is developed to approximate the external disturbances. The proposed adaptive neural compensation control method is constructed by utilizing a backstepping technique. The boundedness of all the closed-loop signals is guaranteed via Lyapunov analysis and the tracking errors are proved to converge to a small neighborhood of the origin. Simulation results are provided to illustrate the effectiveness of the proposed control approach.     

NSGA-Ⅱ和NSGA-Ⅲ应用于换热网络多目标优化的对比

针对换热网络多目标优化问题，采用目前应用较广泛的两种多目标遗传算法，即NSGA-Ⅱ和NSGA-Ⅲ，对两种算法的性能进行对比研究。案例研究结果表明，NSGA-Ⅱ算法比NSGA-Ⅲ算法运行效率更高，NSGA-Ⅲ的运行时间是NSGA-Ⅱ的2倍以上；NSGA-Ⅱ算法的应用并不严格地受限于3个目标的最大目标数量，NSGA-Ⅱ在求解大于3个目标的多目标优化问题时也可能具有良好的性能，目标数量并非选择NSGA-Ⅱ和NSGA-Ⅲ算法的严格标准。对10×5换热网络案例进行4个相关目标改造优化时，从换热网络的单一性能指标来看，NSGA-Ⅱ算法更容易获得各目标的极值。从最小年度总费用的评价指标来看，两种算法的最优方案效果相近。对7×3换热网络案例进行6个目标的优化时，NSGA-Ⅲ算法得到各目标的极值较优。从最小年度总费用的评价指标来看，NSGA-Ⅲ算法获得的投资费用和年度总费用更小。对于目标函数数量不超过3个，或者3个以上具有一定相关性的多目标优化问题，推荐优先使用NSGA-Ⅱ算法实现快速寻优；而NSGA-Ⅲ算法由于其基于参考点的选择机制，运行效率较慢，更适合用于收敛困难的高维多目标优化问题。     

悬浮于润滑油中的颗粒运动分析及其对油膜压力的影响

对含有固体颗粒的局部润滑流域建立格子Boltzmann(LBM)离散模型,分析固体颗粒在润滑油中的动力学特性;考虑颗粒形状的影响,推导计入单个固体颗粒运动的润滑方程,并分析得到油膜压力;将油膜流动特性与颗粒动力学计算相结合,分析不同形状的颗粒运动对于油膜压力的影响。分析发现,当颗粒进入润滑油后,经过很短的瞬时颗粒就会达到一个瞬态稳定的状态,无论颗粒在油膜厚度方向的初始位置位于两壁面之间的中线上侧还是下侧,颗粒都会向中线位置移动;当颗粒速度为0时对于油膜压力的影响较大,随着颗粒速度逐渐增大,颗粒对于油膜压力的影响逐渐减小;当颗粒的宽度在油膜厚度方向相同时,长宽比越大的颗粒对于油膜压力的影响也越大;当颗粒长轴相等时,颗粒在油膜厚度方向的宽度越大,则其对于油膜压力的影响也越大,即颗粒形状对于油膜流动的阻碍能力越强,则其对于油膜压力的影响越大。     

Biological Water Treatment by a Hybrid Fluidized-Bed Bioreactor: Theoretical Study

A hybrid fluidized-bed bioreactor for water purification was proposed and analyzed. It is a novel type of bioreactor characterized by hitherto unknown stationary and dynamic features. Steady-state characteristics of this hybrid bioreactor with external liquid circulation are presented. A quantitative analysis of steady-state properties of the bioreactor was performed with the aid of an original mathematical model developed for a double-substrate aerobic microbiological process. A steady-state analysis of aerobic processes characterized by different oxygen demand was performed. The effect of essential parameters was evaluated, including carbonaceous substrate concentration in the feed stream to the apparatus, aeration intensity, total residence time of a liquid in the bioreactor, and height of the bed of fine carrier particles.