减振器在自导系统结构设计中的应用

通过对减振器结构设计的理论分析，建立了减振器的数学模型，同时通过设计的模拟装置对减振效果进行了实测，效果良好。     

Signal Integrity: Fault Modeling and Testing in High-Speed SoCs

As we approach 100 nm technology the interconnect issues are becoming one of the main concerns in the testing of gigahertz system-on-chips. Voltage distortion (noise) and delay violations (skew) contribute to the signal integrity loss and ultimately functional error, performance degradation and reliability problems. In this paper, we first define a model for integrity faults on the high-speed interconnects. Then, we present a BIST-based test methodology that includes two special cells to detect and measure noise and skew occurring on the interconnects of the gigahertz system-on-chips. Using an inexpensive test architecture the integrity information accumulated by these special cells can be scanned out for final test and reliability analysis.     

三种常用面积注水井网的比较与选择

本较系统地分析了三种常用面积井网系统的注水特点。指明了五点井网系统是面积井网中最强化的一种注水方式，适用于低渗透与特低渗透油藏的注水开发。     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。     

正确选用热力管网保温材料的几个问题

介绍了做好热力管网保温应具备的有关知识和数据，以及宝钢蒸汽主干管网在采用四种保温材料下的经济保温层厚度和相对的节能效益，认为目前适于宝钢公司热源温度在６００℃以下较好的保温材料有新型矿渣棉制品和泡沫石棉板。     

绝对时钟智能控制器的研制

介绍了一种日常参数智能控制器的研制及研制过程中的几个重要问题的解决方法。特别是用于城市照明及美化城市的彩灯的开、关时间智能控制方面，给出了依据当地绝对时间、经度、纬度进行昼夜时间计算的方法，使之在不接光电传感器情况下可跟踪季节的昼夜变化。控制系统采用８９Ｃ２０５１单片机，配有时钟日历芯片ＤＳ１２８８７，系统体积小、功能强、可靠性高。     

DRB32在提高异种机互连传输中的应用

字结构不同的计算机互连，以往用软件转换字结构，增加了软件开销，导致传输效率降低。现介绍一种用硬件逻辑转换的方案，在数据传送过程中，使一台计算机的数据结构适应另一台计算机的要求。简捷、可靠、快速，大大地提高了异种机互连的传输率。     

固相缩聚共聚酯的熔融行为和结晶速率研究

通过固相缩聚合成了两种不同结构的高分子量共聚酯，研究了样品的熔融行为和结晶速率。研究发现，共聚酯的熔融峰随着固相聚合温度和时间的变化而与纯ＰＥＴ有明显的差别，共聚酯泊结晶速率与慢于纯ＰＥＴ的结晶速率。     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

织物弹道贯穿性能分析计算

纤维织物增强复合材料由于轻质和高冲击损伤容限而在防弹装甲设计及制造中逐渐得到应用,如人体防弹衣和车辆防护装甲。但是尚无较好的方法直接计算复合材料防弹特性,其中困难在于复合材料弹道冲击过程中的应变率效应和冲击破坏机理至今没有被揭示。解决问题的第一步是建立复合材料增强相(即织物)防弹特性计算方法。提出基于纤维力学性质应变率效应的织物弹道冲击破坏分析模型,计算不同面密度织物靶体在弹道贯穿过程中的弹体剩余速度,由此反映靶体防弹特性。用本文中提出的简单算法预测的结果与实测结果在靶体厚度不大时极为接近,而且也有可能将其扩展到纤维织物增强复合材料防弹性质的计算。