Impact of the anode operating conditions on the liquid water distribution in the cathode gas diffusion layer

Previous experimental results indicate that the humidification conditions at the anode have an impact on the liquid water distribution in the cathode gas diffusion layer. Numerical simulations are developed to reproduce and analyze this effect. Results consistent with the experimental results are first obtained by playing with the partition coefficients of an advanced pore network model computing the liquid water formation and transfer in the cathode gas diffusion layer (GDL) for a large range of operating conditions. Then, a model for the full anode – cathode assembly is developed by combining the pore network model of the cathode GDL and a 1D model describing the heat and water transfer in the various components of the anode-cathode assembly. This enables one to generalize the dry – wet regime diagram introduced in a previous work by incorporating the effect of the humidity condition at the anode.     

Application of the Microsoft Excel Solver tool in the solution of optimization problems of heat exchanger network systems

Optimization of heat exchanger networks (HEN_S) is a field of interest in Chemical Engineering. The aim is to use the residual heat of process streams to raise the temperature of other process streams which are cold, thus minimizing the use of hot and cold utilities. The usual way to deal with this task is to pose a linear programming problem according to a transshipment model in order to minimize either the general services consumptions or the number of hot and cold stream matchings required. This optimization is subjected to several restrictions given by the energy balances corresponding to each heat exchange.The high number of variables and equations obliges the use of specific software to solve these problems, e.g. GAMS (General Algebraic Modelling System). However, this software is not intuitive and requires a long time of training and a certain level of practice for the students to adequately use it.This work describes the use of Microsoft Excel-Solver for the sequential solving of HEN_S optimization problems according to the transshipment model. Solver is a much simpler, intuitive and easily available tool for the students who, besides, usually learn how to use it in the first years of their degree, in Informatics or similar subjects. Thus, it is not necessary to spend extra time in the teaching of the software, time that may be devoted to other contents.This paper presents an example of HEN_S problem proposed in the subject Simulation and Optimization of Chemical Processes corresponding to the Joint Master in Chemical Engineering of the Rey Juan Carlos University and the Autónoma University of Madrid and solved by the students using Excel-Solver.     

APP软件性能效率研究

性能效率是APP软件的重要质量属性，但目前缺乏APP软件性能效率的通用模型。分析了APP软件的性能特征，基于ISO/IEC 25010标准提出了APP软件的性能效率模型，定义了APP软件性能效率的子特性和度量指标。基于提出的APP软件性能效率模型，通过实验对APP软件的性能效率进行了度量及相关分析。     

Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics–based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.     

Practical Application of the Probabilistic‐Statistical Model of the Suspension Separation in Hydrocyclones

An effective practical approach that allows not only a significant reduction in the scope of practical experiments in the course of studying suspension separation processes in hydrocyclones, but also makes it possible to assess the intensity of random components of the processes and define the interrelation between such components and hydrodynamics of flows in a hydrocyclone is presented. Within the frames of the developed probabilistic‐statistical model of suspension separation in hydrocyclones on the basis of statistical self‐similarity properties, a relationship was found between determined and random components of the processes. This allowed transitioning from three‐parameter probability density functions for suspension particles in hydrocyclones to two‐parameter functions; thus significantly improving the efficiency of practical application of the developed model.     

冷链条件下气调包装酱卤鸭肉制品货架期预测模型的建立

目的 以气调包装酱卤鸭肉制品为研究对象,在冷链温度范围内建立一套准确、高效的货架期预测模型。方法 利用选择性培养基测定不同温度下产品各微生物数量,确定4~25℃条件下产品优势腐败菌。对乳酸菌数量与感官评定值进行了回归分析确定最小腐败量Ns。分别采用修正的Gompertz方程和平方根方程建立一、二级模型,并通过预测值与实测值对比验证模型的可靠性。结果 确定了4~25℃条件下产品优势腐败菌为乳酸菌,最小腐败量Ns=6.14(lg(cfu /g))。一、二级模型拟合度均良好,三种温度下模型预测值与实际值间的差异均在30％左右,波动幅度在10%以内。结论 实现了对4~25℃内任何时间点产品剩余货架期的预测,为冷链条件下气调包装酱卤鸭肉制品品质的变化提供了理论指导。     

Mixture ratio modeling of dynamic systems

Any knowledge extraction relies (possibly implicitly) on a hypothesis about the modelled-data dependence. The extracted knowledge ultimately serves to a decision-making (DM). DM always faces uncertainty and this makes probabilistic modelling adequate. The inspected black-box modeling deals with “universal” approximators of the relevant probabilistic model. Finite mixtures with components in the exponential family are often exploited. Their attractiveness stems from their flexibility, the cluster interpretability of components and the existence of algorithms for processing high-dimensional data streams. They are even used in dynamic cases with mutually dependent data records while regression and auto-regression mixture components serve to the dependence modeling. These dynamic models, however, mostly assume data-independent component weights, that is, memoryless transitions between dynamic mixture components. Such mixtures are not universal approximators of dynamic probabilistic models. Formally, this follows from the fact that the set of finite probabilistic mixtures is not closed with respect to the conditioning, which is the key estimation and predictive operation. The paper overcomes this drawback by using ratios of finite mixtures as universally approximating dynamic parametric models. The paper motivates them, elaborates their approximate Bayesian recursive estimation and reveals their application potential.     

Flow state monitoring of gas-water two-phase flow using multi-Gaussian mixture model based on canonical variate analysis

As a highly complex and time-varying process, gas-water two-phase flow is commonly encountered in industries. It has a variety of typical flow states and transition flow states. Accurate identification and monitoring of flow states is not only beneficial to further study of two-phase flow but also helpful for stable operation and economic efficiency of process industry. Combining canonical variate analysis (CVA) and Gaussian mixture model (GMM), a strategy called multi-CVA-GMM is proposed for flow state monitoring in gas-water two-phase flow. CVA is used to extract flow state features from the perspective of correlation between historical data and future data, which solves the cross correlation and temporal correlation of multi-sensor measurement data. GMM calculates the possibility that the current flow state belongs to each typical flow pattern and judges the current flow state by probability indicators. It is conducive to follow-up use of Bayesian inference probability and Mahalanobis distance-based (BID) indicator for flow state monitoring, which avoids repeated traversal of multiple CVA-GMM models and improves the efficiency of the monitoring process. The probability indicators can also be used to analyze transition flow states. The method combining the probabilistic idea of GMM with the deterministic idea of multimodal modeling can accurately identify the current flow state and effectively monitor the evolution of flow state. The multi-CVA-GMM method is validated by using the measured data of the horizontal flow loop of gas-water two-phase flow experimental facility, and its effectiveness is proved.