The influence of iodide on glass transition temperature of high-pressure nuclear waste glasses

The glass transition temperature (T_g) is a key parameter to investigate for application in nuclear waste immobilization in borosilicate glasses. T_g for several glasses containing iodine (I) has been measured in order to determine the I effect on T_g. Two series of glass composition (ISG and NH) containing up to 2.5 mol% I and synthesized under high pressure (0.5 to 1.5 GPa) have been investigated using differential scanning calorimetry (DSC). The I local environment in glasses has been determined using X-ray photoelectron spectroscopy and revealed that I is dissolved under its iodide form (I⁻). Results show that T_g is decreased with the I addition in the glass in agreement with previous results. We also observed that this T_g decrease is a strong function of glass composition. For NH, 2.5 mol% I induces a decrease of 24°C in T_g, whereas for ISG, 1.2 mol% decreases the T_g by 64°C. We interpret this difference as the result of the I dissolution mechanism and its effect on the polymerization of the boron network. The I dissolution in ISG is accompanied by a depolymerization of the boron network, whereas it is the opposite in NH. Although ISG corresponds to a standardized glass, for the particular case of I immobilization it appears less adequate than NH considering that the decrease in T_g for NH is small in comparison to ISG.     

Sputtered Ir–Ru based catalysts for oxygen evolution reaction: Study of iridium effect on stability

Magnetron sputtered low-loading iridium-ruthenium thin films are investigated as catalysts for the Oxygen Evolution Reaction at the anode of the Proton Exchange Membrane Water Electrolyzer. Electrochemical performance of 50 nm thin catalysts (Ir pure, Ir–Ru 1:1, Ir–Ru 1:3, Ru pure) is tested in a Rotating Disk Electrode. Corresponding Tafel slopes are measured before and after the CV-based procedure to compare the activity and stability of prepared compounds. Calculated activities prior to the procedure confirm higher activity of ruthenium-containing catalysts (Ru pure > Ir–Ru 1:3 > Ir–Ru 1:1 > Ir pure). However, after the procedure a higher activity and less degradation of Ir–Ru 1:3 is observed, compared to Ir–Ru 1:1, i.e. the sample with a higher amount of unstable ruthenium performs better. This contradicts the expected behavior of the catalyst. The comprehensive chemical and structural analysis unravels that the stability of Ir–Ru 1:3 sample is connected to RuO₂ chemical state and hcp structure. Obtained results are confirmed by measuring current densities in a single cell.     

破损水文观测孔涌水封堵技术在高河矿的应用

针对高河矿奥灰水文观测孔空水管锈蚀断裂漏水严重的问题,分析了存在的问题,制定了钻孔涌水封堵技术方案及相应的注浆施工工艺,并进行了为期7天的井下试验。封堵注浆压力达到6 MPa,使用注浆水泥50 t,水泥浆液凝固良好,注浆阀门打开后无出水现象。     

油藏中后期减氧空气驱提高采收率机理研究

尕斯库勒油田E¹₃油藏已经进入高含水时期，储采失衡加剧，综合含水率达到了80%以上，原油产量下降，经济效益变差。为了提高油藏原油采出程度、改善油藏开发效果，调研了国内外减氧空气驱的机理研究以及现场试验的资料，建立了以油藏真实孔渗饱数据为基础的一维条形地层机理模型，并选取该油藏Y12-27井组进行了减氧空气驱可行性验证。研究表明:纵向顶部减氧空气驱驱油效果优于水驱和氮气驱；驱替压力对原油采出程度影响不大；注水转注气可以提高原油采出程度；对于减氧空气驱，由于低温氧化反应的作用，氧气浓度对原油采出程度有一定影响，但比较微弱，其中，氧气浓度为10%时，驱替结束采出程度最高；尕斯库勒油田E¹₃油藏属于注水开发“双高”油藏，适用于减氧空气驱；对于该油藏Y12-27井组，顶部减氧空气驱驱油效果好于水驱和氮气驱，建议氧气浓度超过10%时采取关井等措施。     

Technological and sensorial properties of liquid nitrogen ice cream enriched with protein from brewing waste (trub)

Debittered trub (brewing waste) is an important source of protein source (70.26%). Trub and whey protein were used for 5% protein enrichment of ice cream frozen by liquid nitrogen. Three formulations were elaborated: ice cream standard (ICS), ice cream with whey protein (ICW) and ice cream with trub (ICT). Chemical composition, rheological properties, texture, overrun, melting rate, scanning electron microscopy and a sensorial test were performed. Results showed that ICT presented a higher viscosity, obtained on the upward curve up to 6.76 Pa s⁻¹, consistency index (22.96 (Pa s⁻¹)ⁿ), hysteresis area (140.40 mPa s⁻¹) and hardness (31113.33 g) but a lower melting rate (0.38 g min⁻¹), overrun (13.92%) and sensorial acceptability than the other formulations. The addition of trub debittered for protein enrichment improved ice cream properties and demonstrated that it could be used as a food ingredient.     

Fe-Zn基废脱硫剂制备铁碳材料及其对废水微电解性能

以Fe-Zn基废脱硫剂、煤、Na ₂CO ₃为原料进行高温炭热还原反应，制备了铁碳材料，实现了Zn和S的分离，有望能实现废脱硫剂的综合利用。考察不同工艺条件（配比，温度，时间）对铁碳材料品质，Zn单质分离效率和Na ₂S的收率影响。结果表明： 反应温度≥900℃，煤∶废脱硫剂≥1，Na ₂CO ₃∶废脱硫剂≥1.5，反应时长≥2 h，Zn、S的分离回收效率可达到95%以上。且900℃制备的铁碳材料比表面高达193.6 m ²/g，介孔孔体积为0.028 cm ³/g，炭均匀附着于铁骨架。微电解-芬顿联用降解有机废水实验表明：仅微电解或微电解-芬顿联用（H ₂O ₂=COD=1500 mg/L）时，自制铁碳材料的稳定化学需氧量（COD）去除效率（41.78%、73.56%）都高于商业铁碳（8.43%、48.43%)。本文实验结果表明废脱硫剂与煤和碳酸钠混烧可实现废脱硫剂中Zn与S的分离回收，成功获得了比表面高、去除COD性能好的铁碳材料。     

Research on optimization design of PWR flow distribution device based on numerical simulation

ABSTRACT

In the lower chamber of pressurized water reactor (PWR), the flow distribution device is the core module to distribute coolant into the core. It has complex structure and numerous design parameters. Therefore, it has important theoretical and practical significance to optimize the device. The mesh independence verification, turbulence model selection, and data processing all can influence the numerical simulation results of the lower chamber, in order to research the influence, a numerical simulation method based on the original model of CNP1000 reactor lower chamber is proposed in this paper. In the method, an optimization design method of flow distribution device is established based on surrogate model. The main design variables and optimization objectives are determined based on the device’s structure and function characteristics. And then it respectively adopts Kriging algorithm and multi-objective genetic algorithm to establish a surrogate model of flow distribution device and optimize it globally. Finally, the optimal design variables are obtained. Compared with the device’s performance before optimization, the after optimization has smaller total pressure loss and more uniform flow. The effectiveness and practicability of proposed optimization design method can be verified.     

Mesoporous g-C3N4 decorated by Ni2P nanoparticles and CdS nanorods together for enhancing photocatalytic hydrogen evolution

Ni₂P nanoparticles and CdS nanorods were grew together on a mesoporous g-C₃N₄ through a facile in-situ solvothermal approach. Under visible light (λ > 400 nm), the as-prepared ternary PCN–CdS-5% Ni₂P composite displays a high H₂ evolution rate with 2905.86 μmol g^?1 h^?1, which is about 14, 18 and 279 times that of PCN–CdS, PCN–Ni₂P and PCN, respectively. The enhanced photocatalytic activity is mainly attributed to the improved separation efficiency of the photocarriers by the type II PCN–CdS heterojunction and the effective extraction of photogenerated electrons by Ni₂P. Meanwhile, Ni₂P acts as co-catalyst to provide the photocatalytic active site for hydrogen reduction. In addition, PCN–CdS-5% Ni₂P composite exerts good stability in 12-h cycles.