Warm-white light performance of Dy3+, Eu3+: NaLa(WO4)2 phosphors excited with a 450-nm LED

Dy³⁺, Eu³⁺: NaLa(WO₄)₂ phosphors are successfully synthesized through the solid-state reaction technique. The phase-structure and morphology are measured via X-ray diffraction and energy dispersive spectrometry. The concentrations of Dy³⁺, Eu³⁺, La³⁺, and W⁶⁺ are measured via ICP. The absorption and excited spectra are presented, which indicate that a blue band ranging from 430 to 480 nm is suitable for excitation. Using a commercial blue LED with a wavelength of 450 nm as the excitation light source, emission spectra for samples with varying dopant concentration ratios of Dy³⁺ to Eu³⁺ are obtained, which show good tunable yellow and red emission. For the purpose of investigating white LED performance, CIE spectra and a white light photo are also presented. The results reveal that varying the dopant concentration ratio of Dy³⁺ to Eu³⁺ plays a key role in the warm-white performance. With increasing concentration of Eu³⁺, the correlated color temperature decreases from 4069 to 3172 K, which indicates good warm-white performance.     

Microstructure and permeability of porous YSZ ceramics fabricated by freeze casting of oil-in-water suspension

Porous yttria-stabilized zirconia (YSZ) ceramics are fabricated through freeze casting of oil-in-water suspension followed by sintering at 1250−1550 °C. The pore structure, compressive strength and permeability of porous YSZ ceramics are tailored via altering the emulsion content and sintering temperature. The samples obtained using higher emulsion content or at lower sintering temperature show larger Darcian and non-Darcian constants due to their higher open porosity and larger pore size. Furthermore, the investigation on individual contributions of viscous and inertial resistances on the total pressure drop during permeation process indicates that the viscous resistance increases but the inertial resistance decreases with increasing the emulsion content or decreasing the sintering temperature for samples. Porous YSZ ceramics obtained in this work with a k₁ range of 3.14 × 10⁻¹³–1.12 × 10⁻¹² m² are appropriate for applications in filters and membrane supports.     

Effect of lanthanum doping on water content and diffusion properties of corundum for producing transparent ceramics

The effect of doping corundum with lanthanum on the content of water and other gas impurities, on the diffusion characteristics, on the unit cell size and static strength of fine-crystalline corundum synthesized under thermovapours conditions in a supercritical water fluid was studied.Content, release and diffusion coefficients of water and other volatile impurities in corundum were measured by kinetic thermodesorption mass spectrometry. Water is the main volatile impurity in fine-crystalline corundum. It was found that the introduction of lanthanum into the structure of corundum reduces several times the content of water and other gas-liquid impurities. An increase in the diffusion coefficient of water during the doping of corundum with lanthanum leads to an increase in the degassing rate of fine-crystalline raw materials. When doping corundum, lanthanum, being localized in structural defects, not only displaces structural hydroxyl groups with the formation of strong aluminate-like bonds, but also decreases in the unit cell and increases in the average static strength of the crystals. La-doped corundum, due to the reduced content of water and other gas impurities, is a promising raw material for the production of transparent ceramics.     

燃料电池空气电极的孔道结构调控

燃料电池是将化学能转化成电能的装置，其空气电极催化层的设计，既要包含丰富的、易于接近的反应活性位，也要具备高度连通的电子、质子以及反应物、产物传质通道，因此电极必须具有特定三维几何结构形貌和有序分布的各功能化孔道，确保催化活性位得以充分利用以及反应可以连续进行。针对催化剂孔道的几何结构调控，本文调研了最近报道的一系列研究工作，从模板法、高温相变法、模板/相变复合方法以及基于金属有机框架材料进行孔道设计等四种主要方法出发，综述了该领域的最新研究进展。     

Bond characteristics,vibrational spectrum and optimized microwave dielectric properties of chemically substituted NdNbO4

Coordination chemistry, bond state and vibrational spectrum of co-substituted microwave dielectric NdNb_1-x(Zr_0.5W_0.5)_xO₄ ceramics (x = 0.01∼0.05) were investigated. Raman spectra and XRD refinement showed a solid solution was formed. The compressed and elongated chemical bonds are responsible for the variations of crystal parameters and cell volume. Calculated chemical bond parameters indicated bond covalency, lattice energy and Nb-site bond energy act on the fluctuations of the permittivity, quality factor and temperature coefficient, respectively. Meanwhile, the infrared vibrational spectrum is fitted to quantify the contributions of observed IR mode to the intrinsic loss. Compact ceramic possesses excellent properties: ε_r ∼ 19.2, Q × f ∼ 55282 GHz and τ_f ∼ -11.36 ppm/°C with x = 0.04, at 1250°C.     

Effects of corrosion in liquid fluoride salt on the tensile strength of domestic SiC fibers

The relationship between the tensile strength of corroded domestic second-generation (2ed-gen) SiC fibers at various temperatures for 500 h in 46.5LiF-11.5NaF-42.0KF (mol. %) eutectic salt and the typical microstructure was studied. Weibull theory was used to analyze the critical defects that caused the tensile fracture, and the microstructure of fibers before and after corrosion was characterized. It is concluded that the decrease of tensile strength after corrosion at 800 °C is caused by the surface injury of fibers, which led to the shift of critical defects from the internal defects of virgin fibers to surface defects. Moreover, corrosion at higher temperature accelerates the corrosion process and dissolve the surface O-contained layer thoroughly. This shifts the critical defects back to the internal defects and will be helpful for the recovery of tensile strength of corroded fibers at the higher temperature.     

Ablation behavior of (TiZrHfNbTa)C high-entropy ceramics with the addition of SiC secondary under an oxyacetylene flame

The ablation behavior of high-entropy ceramics (HECs) was investigated in this study using an oxyacetylene flame at 2000 °C. Spark plasma sintering was used to construct a dense HEC (TiZrHfNbTa)C with a 20 vol% of SiC addition (HEC-20SiC). The densification of HEC-20SiC can be improved to a certain extent by adding SiC particles, increasing the hardness of HEC-20SiC to up to 24.6 GPa, and the crack deflection observed through the addition of SiC particles were considered to be the strengthening and toughening mechanisms. After ablation, Hf₆Ta₂O₁₇, Ti_5.1Ta_4.9O₂₀, Nb₂Zr₆O₁₇, TaZr_2.75O₈, and SiO₂ can be detected on an ablated surface and HEC-20SiC possesses the minimum mass ablation rate (?1.9 mg s^?1) and line ablation rate (2.1 μm s^?1) among the comparative ceramics. On the one hand, the SiC phase forms gaseous CO, CO₂, and SiO as well as viscous SiO₂ during ablation and some part of the heat can be dissipated by the evaporation of gaseous CO, CO₂, and SiO; further, pore defects can be healed by viscous SiO₂, thus inhibiting the diffusion of reactive oxygen species. On the other hand, the HEC phase with a lattice-distortion caused by single-phase solid-solution can effectively inhibit the invasion of reactive oxygen species and the outward migration of metal atoms. The invasion rate of reactive oxygen is considered to be the main step during HEC-20SiC ablation, and it is believed that higher principal component HECs can improve ablation performance even further.     

Energy storage performance of 0.55Bi0.5Na0.5TiO3-0.45SrTiO3 ceramics doped with lanthanide elements (Ln = La,Nd, Dy,Sm) using a viscous polymer processing route

Lead-free bismuth sodium titanate-strontium titanate (NBT-ST) dielectric ceramic materials have been extensively investigated energy storage materials because of their relaxor characteristics. In this study, four different lanthanide elements were introduced into the ferroelectric NBT-ST ceramic to improve their relaxor properties. The introduction of the lanthanide resulted in an increase in disorder at location A within the perovskite lattice and improved relaxor characteristics, leading to a stored energy density of more than 3.5 J/cm³. In particular, an ultrahigh recoverable stored energy density of 4.94 J/cm³ and efficiency of 88.45% were achieved at 440 kV/cm when the NBT-ST ceramic was modified with neodymium. The modified ceramic also exhibited good thermal stability in the range of 30–120 °C, as well as a fast discharge time of ～153 ns, indicating that Nd-incorporated NBT-ST is a promising candidate for electrical energy storage ceramic.     

Characterization of anisotropic gas permeability and thermomechanical properties of highly textured porous alumina

Porous alumina with a highly textured microstructure was fabricated by pulse electric current sintering (PECS) using alumina platelets. Highly oriented porous alumina with a porosity of 3%–50% was obtained by a pressure-controlled method of PECS. The properties of the highly textured porous alumina were measured in two directions. The nitrogen gas permeance and thermal conductivity at room temperature were higher in the direction along the platelet length due to the higher continuity of pores and the connectivity of alumina platelets, respectively. The anisotropy of the thermal conductivity at room temperature was investigated and explained by the effect of grain size of platelets as well as morphology and orientation of pores. The bending strength was higher with the loading direction along the platelet thickness. The thermal shock strength was clearly different in the two directions. The difference in the thermal shock strength was investigated by the measurement of properties and thermal stress analysis.     

Simultaneously enhancing mechanical and microwave absorption properties of Cf/SiC composites via SiC nanowires additions

C_f/SiC composite is an excellent structural and functional material, silicon carbide nanowires (SiCnws) are not only a toughening material but also a great application in the field of microwave absorption. In this study, SiCnws are grown on the surface of carbon fiber (C_f) by polymer impregnation and pyrolysis, and the SiC matrix was prepared by chemical vapor osmosis method. The SiCnws are introduced to enhance the mechanical and microwave absorption properties simultaneously. After 3 impregnations, the flexural strength of the composite was 107.35 ± 10 MPa. When the thickness is 1.86 mm, the minimum reflection loss value is ?41.08 dB, and the effective absorption bandwidth (RL ≤ ?10 dB) is 3.86 GHz. Furthermore, the microwave absorption mechanism of the material is discussed. This work provides a new method to prepare lightweight, stable and high-performance microwave absorption materials, and these materials are expected to be used in high temperature environments.