工艺参数对纳米颗粒Cu/SiO_2复合薄膜结构和光谱特性的影响

用离子束溅射法制备了具有反常光吸收特性的纳米颗粒CU／SiO2复合薄膜。获得了在离子来参数一定时，基片温度、膜料的沉积时间和镀膜后的保温时间等工艺参数对这种薄膜结构和光学特性的影响规律，并对纳米颗粒Cu／SiO2复合薄膜的反常光吸收特性作了计算和解释。     

离子注入中污染的产生及防护

本文概述了离子注入过程中污染产生的原因和防止污染的措施，特别强调了对微粒污染和金属污染的防护以满足ＵＬＳＩ加工对离子注入的要求。     

用轴向气胎式离合器,制动器改造旧飞剪

采用轴向式气胎离合、制动器，改造了旧飞剪，解决了原剪机电磁离合、制动器控制不准确的问题；该剪机改造后在成品轧机后使用，剪切用１２０ｍｍ×１２０ｍｍ坯生产的大规格产品（１８ｍｍ以上），增产、增效，年总经济效益为９７．８万元     

SnO2超微粒子薄膜的气敏特性研究

作者用自行设计的直流气体放电活化反应蒸发装置制备出平均粒径约为40nm的SnO_2超微粒子薄膜.研究了不同氧分压下所得SnO_2超微粒膜的形貌、结构和组成等特性,以及不同样品对各种易燃气体的气敏特性,得出了灵敏度随氧分压及灵敏度随工作温度的变化曲线.     

应用粒子动态分析仪研究水力旋流器流场

利用粒子动态分析仪(PDA),对水力旋流器内固相颗粒流场做了全面的测定,得出水力旋流器内固相颗粒的流态、浓度及粒度分布,为进一步查清水力旋流器的工作机理提供了重要理论依据。     

径向磁悬浮轴承结构特性研究及其模型的建立

本文分析研究了径向可控磁悬浮轴承的多磁极结构对系统模型的影响，推导并建立了一种新的考虑耦合作用的数学模型。     

Chemical leaching and magnetic properties of non-equilibrium Al(Co–Cu) powders produced by rod milling

We report upon the chemical leaching and magnetic properties of nanoscale crystalline Al_0.6(Co₂₅Cu₇₅)_0.4 alloy powders produced by rod milling. X-Ray diffractometry (XRD), transmission electron microscopy, differential scanning calorimetry, vibrating sample magnetometry, and superconducting quantum interference device magnetometry were used to characterize the as-milled and leached specimens. After 400 h of milling, only the b.c.c. phase of the intermetallic compound γ-Al_3.892Cu_6.10808 was detected by XRD. After annealing the leached specimen at 600 °C for 1 h, the nanoscale crystalline phase was transformed into the f.c.c. Cu phase, and this was accompanied by a change in the magnetic properties. The peaks of the magnetization shifted towards lower temperature with increasing external field. The temperature behavior at T_f (45 K) for direct current (d.c.) magnetic susceptibility measurements was quite different for field cooling and zero-field cooling. After cooling the leached specimen from 800 °C, magnetization increased gradually.     

SHAPE GENERALIZED ISOTHERMAL EFFECTIVENESS FACTOR FOR FIRST-ORDER KINETICS

A generalized effectiveness factor equation (Eq. (32)), in terms of modified Bessel functions, is derived for a catalyst pellet of arbitrary shape. The derivation is based on utilizing an appropriate one-dimensional approximation for the Laplacian in an arbitrary shaped body subjected to a uniform external concentration field. The comparison of the result with the available expressions for various geometries is highly satisfactory. It unifies the expressions for the three fundamental shapes, viz., infinite slab, infinite cylinder and sphere, and also compares very well with the exact solutions for finite shapes over the entire range of the Thiele modulus.     

溶胶-凝胶法制备HAP骨水泥材料的研究

文章对用溶胶－凝胶法（简称SOL－GEL）烧结制备HAP骨水泥材料的工艺条件进行了研究，并探索了HAP粉剂与柠檬酸水溶液构成和凝结体系的可行性，结果显示出该材料作为医用骨水泥材料的可能性。     

Numerical simulation of typical contact situations of brake friction materials

In the paper, a model typical for contact situations of automotive brakes is established based on the method of movable cellular automata. The processes taking place at local contacts in an automotive brake system are analysed. Based on microscopic and micro-analytical observations, the following contact situations were simulated: (i) a couple of ferritic steel against pearlitic steel, both covered by an oxide layer mixed with graphite nanoparticles and (ii) the same situation but without oxide layers. The results of calculated mean coefficients of friction of the oxide-on-oxide contact correspond well to expected values for a real braking system, whereas steel-on-steel contact are twice as high. This allows one to make some conclusions; for example, oxide formation will take place more quickly than friction layer elimination, and finally this is responsible for the stabilisation of the coefficient of friction.