FeBP非晶态合金超细微粒的合成及其对PH3分解的催化作用

用化学还原法合成了FeBP非晶态合金超细微粒，用电感耦合等离子体光谱（ICP）、X射线粉末衍射（XRD）、透射电子显微镜（TEM）和差热分析（DSC）等手段对其进行了物性表征，并用微型催化反应装置考察了其对PH3分解的催化作用，结果表明，非晶态合金FeBP对PH3的分解具有良好的催化作用，能使PH3的分解温度从800℃以上降到500℃左右。490℃时分解率超过90％，540℃时达100％。     

以表面负载季铵盐阳离子型苯/丙乳胶粒为模板制备ZrO_2空心微球

以C9油与甲基丙烯酰氧乙基三甲基氯化胺的共聚物P(C9-DMC)为乳化剂制备苯/丙阳离子乳胶粒,并以其为模板,利用直接包覆法制备了由17 nm左右微晶体堆成的ZrO2空心微球。所制得的样品采用FT-IR、XRD、TEM和SEM等进行了表征。     

Preparation of Plate Fe_(60)Co_8Zr_(10)Mo_5W_2B_(15) Bulk Amorphous Alloy and Its Fracture Toughness

1Introduction Duwez[1]synthesizedthefoilAu Siamorphousalloyforthefirsttimewithrapidsolidification,whichinitiatedthepreparationofamorphousalloysintheprocessofalloysolidification,andthereaftertheresearchonamorphousal loysdevelopedrapidly.Since1980s,withthec…     

聚苯硫醚复合涂层的耐磨性能

研究了用固体润滑石墨、碳化硅、二硫化钼等填料改性的聚苯硫醚 (PPS)涂层的耐磨性能。实验结果表明 ,聚苯硫醚复合涂层具有优良的耐磨性 ;加入适量 ( 3 0 % )的石墨、碳化硅等固体润滑剂 (石墨 :碳化硅 =2∶3 ) ,可以有效提高涂层的耐磨性能 ,而二硫化钼和三氧化二铬的减摩效果更佳     

Effects of thermal and mechanical treatments on a titanium-based conversion coating for aluminium alloys

The influence of mechanical deformation and heating on the protective performance of a chromium-free conversion treatment for aluminium alloys has been assessed by polarisation and AC impedance measurements. Protection is unlikely to be seriously compromised by typical production operations.     

液晶光阀光电导层光吸收系数的研究

用化学气相沉积法制备了液晶光阀中光电导层———非晶硅薄膜,从实验中得出最佳制备工艺的参数取值。给出了用包络线法测量非晶硅薄膜光吸收系数的原理,测量了样品的光吸收系数随波长的变化规律。得到样品在最佳工艺条件下的光吸收系数高于1×103cm-1。     

Al-Zn-Ce非晶合金的相选择与组织结构演化

本文研究了具有典型分解特征的Al-Zn-Ce非晶合金的形成和晶化过程，探讨了各种相的生成顺序。XRD和DSC测试结果表明强烈的化合物短程序有利于Al-Zn-Ce非晶合金的形成。在Al-Zn-Ce非晶合金的晶化过程中存在复杂的相选择行为，多种相的竞争形核和有限生长使其具有复杂的结构特点。同时，结果也表明冷速对该体系非晶的形成有很大影响。     

高合金钢铸造用涂料的试制与开发

介绍了炉爪用合金钢1Cr25Ni20Si2Re,导板用合金钢2Cr32Ni5采用串箱铸造过程中，有关镁砂粉涂料和石英粉涂料的试制。结果表明：镁砂粉涂料为不透气涂料，不太适用，而合理配方的石英粉涂料使用性能良好。     

Experimental Study on Polymer Artificial Bone with HA Coated and Fiber Liners

1Introduction HA(hydroxyapatite)wasakindofbioactiveceram ics,whichhadexcellentbiocompatibilityandtissueaffin ityinthatitscomponentsweresimilartothoseofhuman bone[1].Soitwasthebestknownhumanbonesubstitute,andunprecedentedeffecthadbeenharvestedinrecenttwo d…     

Plasma Sprayed Hydroxyapatite Coatings with Nano-hydroxyapatite Prepared by Ultrasonic Precipitation Process

Nano-particle hydroxyapatite （ HA ） was prepared with a novel ultrasonic precipitation process and the as-prepared nanopowder was used to produce hydroxyapatite （ HA ） coatings on titanium substrate via plasma spraying. The phase and the microstructare of the coating were characterized by X- ray diffraction （XRD） and scanning electron microscopy （SEM）. Results showed that spherical particles could be prepared by ultrasonic precipitation process; and a corresponding dense HA coating with molten surface and low-porosity cross-section structure was acquired. During the plasma spraying process, new phases of Ca3 （ PO4 ）2 and Ca2 P2O7 were generated. After heat-treating at 800℃ for 1 h, the contents of Ca3 （ PO4 ）2 and Ca2 P2O7 decreased while HA content increased. Tensile adhesion tests showed that the plasma sprayed coating prepared with the spherical nanoparticles exhibited high tensile bond strength.