Evolution mechanism of the microstructure and mechanical properties of plasma-sprayed yttria-stabilized hafnia thermal barrier coating at 1400 °C

Yttria stabilized hafnia (Hf_0.84Y_0.16O_1.92, YSH16) coatings were sprayed by atmospheric plasma spraying (APS). The effects of thermal aging at 1400 °C on the microstructures, mechanical properties and thermal conductivity of the coatings were studied. The results show that the as-sprayed coating was composed of the cubic phase, and the nano-sized monoclinic (M) phase was precipitated in the annealed coating. The presence of M phase effectively constrained the sintering of the coating due to its superior sintering-resistance. The Young's modulus kept at a nearly same level of ~78 GPa even after annealing, and the coating annealed for 6 h yielded a maximum value of hardness but revealed a declining tendency in the Vicker's hardness with prolonged sintering time. The thermal conductivity increased from 0.8-0.95 W m^-1 K^-1 at as-sprayed state to 1.6 W m^-1 K^-1 after annealing at 1400 °C for 96 h. The dual-phase coating is promising to serve at temperatures above 1400 °C due to its excellent thermal stability and mechanical properties.     

Synergistic effects of modified TiO2/multifunctionalized graphene oxide nanosheets as functional hybrid nanofiller in enhancing the interface compatibility of PLA/starch nanocomposites

The aim of this study is to investigate the synergistic effects of modified TiO₂/multifunctionalized graphene oxide nanosheets at different ratios on the interface compatibility between starch and poly(lactic acid) (PLA). To this end, silanylated nano-TiO₂ (MTiO₂, 1 and 2%) and alkylated maleic anhydride grafted graphene oxide (f-GO, 0.1, 0.2, and 0.4%) at different combinations are blended with the PLA-starch composites using solution blending technique. Then, the synergistic effects of MTiO₂ and f-GO on PLA/starch matrix are investigated in terms of the morphology, crystallinity, structural characterization, thermal stability, dynamic mechanical, and antiaging properties, and the related mechanisms. The Raman and Fourier transform infrared spectroscopy spectra verify the successful synthesis of the two modified nanofillers (f-GO and MTiO₂) and the formation of strong hydrogen bond within the PLA-starch nanocomposites. Due to the strong interfacial interaction and the synergistic effect from the combination of 1% MTiO₂ and 0.2% f-GO, obvious improvement was observed in PLA-starch versus other nanocomposites in terms of morphology, thermal stability, surface hydrophobicity, storage modulus, ultraviolet-shielding capacity, and aging-resistance. Furthermore, differential scanning calorimeter (DSC), isothermal crystallization kinetic, and X-ray diffraction analysis demonstrate that f-GO and the M-TiO₂ significantly synergize in enhancing the crystallization rate and crystallinity of PLA/starch matrix. These results provide novel insights for constructing high-performance nanocomposites and facilitate their applications in food packaging.     

Corrosion behavior of air plasma spraying zirconia-based thermal barrier coatings subject to Calcium–Magnesium–Aluminum-Silicate (CMAS) via burner rig test

Three different kinds of thermal barrier coatings (TBCs) — 8YSZ, 38YSZ and a dual-layered (DL) TBCs with pure Y₂O₃ on the top of 8YSZ were produced on nickel-based superalloy substrate by air plasma spraying (APS). The Calcium–Magnesium–Aluminum-Silicate (CMAS) corrosion resistance of these three kinds of coatings were researched via burner rig test at 1350 °C for different durations. The microstructures and phase compositions of the coatings were characterized by SEM, EDS and XRD. With the increase of Y content, TBCs exhibit better performance against CMAS corrosion. The corrosion resistance against CMAS of different TBCs in descending was 8YSZ + Y₂O₃, 38YSZ and 8YSZ, respectively. YSZ diffused from TBCs into the CMAS, and formed Y-lean ZrO₂ in TBCs because of the higher diffusion rate and solubility of Y³⁺ in CMAS than Zr⁴⁺. At the same time, 38YSZ/8YSZ + Y₂O₃ reacts with CAMS to form Ca₄Y₆(SiO₄)₆O/Y_4·67(SiO₄)₃O with dense structure, which can prevent further infiltration of CMAS. The failure of 8YSZ coatings occurred at the interface between the ceramic coating and the thermally grown oxide scale (TGO)/bond coating. During the burner rig test, the Y₂O₃ layer of the DL TBCs peeled off progressively and the 8YSZ layer exposed gradually. DL coatings keep roughly intact and did not meet the failure criteria after 3 h test. 38YSZ coating was partially ablated, the overall thickness of the coating is thinned simultaneously after 2 h. Therefore, 8YSZ + Y₂O₃ dual-layered coating is expected to be a CMAS corrosion-resistant TBC with practical properties.     

水提法提取—电感耦合等离子体质谱法测定婴幼儿配方奶粉中的碘

用水提取婴幼儿奶粉中的碘,亚铁氰化钾和乙酸锌盐析法沉淀蛋白,过滤后可以得到澄清处理液。用电感耦合等离子体质谱对提取样液进行测定,130Te作为内标物进行定量分析。该方法简便快捷,检出限为0.10 mg/kg加标回收率为90.8%~109%,相关系数0.999,精密度试验RSD2%。     

基于关键路径延时检测的自适应电压缩减技术

为了减小传统的最差情况设计方法引入的电压裕量,提出了一种变化可知的自适应电压缩减(AVS)技术,通过调整电源电压来降低电路功耗.自适应电压缩减技术基于检测关键路径的延时变化,基于此设计了一款预错误原位延时检测电路,可以检测关键路径延时并输出预错误信号,进而控制单元可根据反馈回的预错误信号的个数调整系统电压.本芯片采用SMIC180 nm工艺设计验证,仿真分析表明,采用自适应电压缩减技术后,4个目标验证电路分别节省功耗12.4％,11.3％,10.4％和11.6％.     

Design and performance study of phase‐locked loop using fractional‐order loop filter

The present work reports the realization of an analog fractional‐order phase‐locked loop (FPLL) using a fractional capacitor. The expressions for bandwidth, capture range, and lock range of the FPLL have been derived analytically and then compared with the experimental observations using LM565 IC. It has been observed that bandwidth and capture range can be extended by using FPLL. It has also been found that FPLL can provide faster response and lower phase error at the time of switching compared to its integer‐order counterpart. Copyright © 2014 John Wiley & Sons, Ltd.     

Managing readiness-relevant activities for the organizational dimension of ERP implementation

An organization requires performing readiness-relevant activities to ensure successful implementation of an enterprise resource planning (ERP) system. This paper develops a novel approach to managing these interrelated activities to get ready for implementing an ERP system. The approach enables an organization to evaluate its ERP implementation readiness by assessing the degree to which it can achieve the interrelated readiness relevant activities using fuzzy cognitive maps. Based on the interrelationship degrees among the activities, the approach clusters the activities into manageable groups and prioritizes them. To help work out a readiness improvement plan, scenario analysis is conducted.     

Digital image correlation strain measurement of thick adherend shear test specimen joined with an epoxy film adhesive

Structural bonding and bonded repairs of composite materials become more and more important. Understanding the strain within the bondline leads to suitable bonding design. For new design approaches the strain distribution within the bondline has to be analyzed. Thus, often finite element analysis (FE) are used. However, a huge challenge is the availability of reliable material properties for the adhesives and their validation. Previous work has shown that it is possible to measure the small displacements resulting within thin epoxy film adhesives using high resolution digital image correlation (DIC). In this work a 2D DIC setup with a high resolution consumer camera is used to visualize the strain distribution within the bondline over the length of the joint as well as over the adhesive thickness. Therefore, single lap joints with thick aluminum adherends according to ASTM D 5656 are manufactured and tested. Local 2D DIC strain measurements are performed and analyzed. Two different camera setups are used and compared. The evaluation provides reliable material data and enables a look insight the bondline. The results of the full field strain data measured with DIC are compared with numerical simulations. Thus, material models as well as chosen parameters for the adhesive are validated. Compared to extensometers, giving only point-wise information for fixed measuring points, the DIC allows a virtual point-wise inspection along the complete bondline. Furthermore, it allows measuring close to the bondline to reduce the influence of adherend deformation.