On certain aspects of strain rate sensitivity of sheet metals

The formability of a material depends upon the strain hardening and strain rate hardening of the material. In this study, constitutive parameters using the power law constitutive equation are determined for six different strength steels and two aluminum alloys over different strain ranges, including approximations of the postuniform elongation range. Constitutive parameters are found to be different at different strain ranges. The strain hardening of steels increases with strain at low strain levels (less than 5%) and decreases at high strain levels (greater than 10%). Strain rate hardening decreases with strain for all steels and aluminum alloys. Uniform elongation depends only on strain hardening, and postuniform elongation depends only on strain rate hardening. However, the total elongation depends on both strain hardening and strain rate hardening.     

热处理对多孔铝合金压缩吸能性能的影响

采用渗流铸造工艺 ,制备了Al Si系多孔铝合金 ,讨论了其压缩变形特征及能量吸收性能 ,分别对ZL10 1、ZL111两种多孔铝合金进行T6热处理 ,研究了热处理对这两种多孔铝合金压缩吸能性能的影响。研究结果表明 ,热处理能够提高多孔铝合金的能量吸收能力 ,对屈服强度及能量吸收效率也有显著的影响 ,为提高多孔铝合金的压缩性能 ,应尽可能施行热处理     

Effect of equal channel angular extrusion on the microstructure and superplasticity of an Al-Li alloy

This research investigates the use of equal channel angular extrusion (ECAE) processing to produce a superplastic form of the aluminum alloy 2098. The starting material was a hot-rolled and precipitation-hardened plate with elongated grains of width 67–92 μm, and a composition in weight percent of 2.2% Li, 1.3% Cu, 0.73% Mg, 0.05% Zr, balance Al. Microstructural evolution was investigated with optical and transmission electron microscopy (TEM) and microhardness measurements after each step of a multipass ECAE process. ECAE produced a submicron grain structure with an average size of about 0.5 μm. The sub-grain microstructure size was a function of the magnitude of the input strain and the extrusion temperature. Misorientation angles of the developed submicron structure increase with increasing number of passes at warm working temperatures. Superplastic behavior of the ECAE-processed alloy was achieved. However, the low zirconium content of the 2098 alloy resulted in grain growth of the refined structure at the superplastic processing temperatures, placing a lower limit on the deformation rates that can be used.     

定向凝固的进展对高纯铝偏析法提纯工艺的影响

铝提纯工艺为高纯铝发展的关键。现在国内外通用的高纯铝制备工艺为三层液电解法和分步冷凝法。由于能耗高或提纯效率低，这两种工艺都不能完全满足当今工业发展的需要。针对当前广泛采用的凝固偏析法，结合定向凝固的新进展，讨论了改进结晶方式，提高提纯效率和生产效率的工艺方法。     

宽幅高速铝箔轧机轧制铝箔面残留油的原因及其预防

介绍了宽幅高速铝箔轧机轧制铝箔过程中，箔面残留油对产品质量的影响，探讨了箔面发生残留油的原因及其改进措施。     

铝合金激光-电弧复合焊接工艺研究

对LF6铝合金的激光-电弧复合焊接工艺进行了初步研究。通过工艺试验,分析研究了焊接速度、激光焦点位置、钨极与激光束之间的距离、焊接电流对焊缝质量(熔深、熔宽)的影响规律。     

Effect of pulse parameters on microstructure of joint in laser beam welding for SiC_p/6063 composite

1　INTRODUCTIONSiC particlesreinforcedcomposites ,thankstotheirlowcostsandhighlevelofstructuralproperties ,areshowingtheirpotentialincivilandmilitaryappli cation .SiC particlesreinforcedaluminummatrixcomposites wideapplicationinaerospaceandautomo tiveareattributedtotheirperformanceofhighspecif icstrength ,highspecificstiffness ,highelasticmodu lusandexcellentwearresistance .Thecoefficientofthermalexpansionandthermalconductivitycanberegulatedbychangingthecontentandsizeofrein forcingparticl…     

智能温度控制仪在铝电解铸造保温炉上的应用

简要介绍了KX-C智能温控仪的性能、特点;结合铝电解铸造保温炉的控制要求,阐述了KX-C智能温控仪对保温炉的恒温控制过程。应用表明,该仪器由于具有控制准确、动作灵敏、接线简单、无需校准、成本较低、可靠性高、无需维护等优点,可很好满足实际生产的要求。     

我国铝土矿资源综合分析

综合分析了我国铝土矿资源分布格局、矿床特征和矿石特点及其对氧化铝工业的决定性制约作用,为我国铝工业"十·五"及其远景规划提供资源基础资料与建议.     

煤矸石制备聚合氯化铝铁钙与应用试验研究

以煤矸石为原料,经过高温焙烧、酸浸、聚合、熟化等过程制备了高效无机高分子絮凝剂聚合氯化铝铁钙（PAFCC）,通过单因素试验研究了PAFCC制备条件对浊度、COD和UV₂₅₄去除率的影响。试验结果表明,PAFCC最佳聚合条件为pH值2、聚合温度60℃、聚合时间5 h、在40℃下熟化28 h。混凝结果表明：制备的PAFCC对浊度有极好的去除效果,达95.70%,同时,对COD、UV₂₅₄也有一定的去除效果,去除率分别达到47.51%、45.98%。炼化废水混凝结果表明：PAFCC对浊度和总磷有较好的去除效果,同时,对COD及氨氮也有一定的去除效果,效果明显优于传统PAC。