絮凝-固化联合真空预压处理高含水率淤泥(浆)试验研究

絮凝-固化联合法（FSCM）是超高含水率疏浚泥浆（EHW-MS）处理和循环利用的合理选择。然而,面向对填料力学性能要求较高的资源化利用情形时,FSCM在固化效率上仍存在一定的局限性。在FSCM的基础上引入低位真空预压技术（VP）,对EHW-MS用作路堤填料提出了一套新的技术方法——真空预压-絮凝-固化联合法（VP-FSCM）,以达到淤泥浆深度脱水、提高固化效率的目的。通过开展一系列室内模型试验,来确定所提出的VP-FSCM的优越性,并探究其处理优势随等效初始含水率的变化规律;结合微观测试手段,分析和论证了VP-FSCM的内在机理和可行性。结果显示,采用VP-FSCM能使试样的不排水抗剪强度最高提高至FSCM的1.65倍,并且强度优势稳定在1.2倍以上。其处理优势在微观层面上表现为C（A）SH凝胶、钙矾石等水化产物数量及发育程度得到明显提升,进一步填充与密实土体结构。     

真空预压联合间歇电渗加固疏浚淤泥试验研究

沿海地区的疏浚工程产生了大量疏浚淤泥。为了研究疏浚淤泥的处理方法,通过室内模型试验,对温州地区的疏浚淤泥进行了分级真空预压联合间歇电渗的加固处理,并对间歇通电的时间及间歇逐级加压电渗进行了研究。试验过程中监测了真空压力、电流、排水量和土表的沉降;试验之后,对土体含水率、十字板剪切强度以及电极腐蚀质量进行了测量。试验结果表明,虽然间歇通电时间越长,土体固结效果越好,但是间歇通电时长超过24 h时,土体加固效果开始减弱;然而,电极腐蚀质量和间歇电渗的平均能耗系数却依然与间歇通电时长呈正相关。此外,分级真空预压联合间歇逐级加压电渗法相比于分级真空预压联合间歇电渗法获得了更佳的土体加固效果,并且其电极腐蚀质量和间歇电渗的平均能耗系数也显著降低。     

Review on the effect of heat exchanger tubes on flow behavior and heat/mass transfer of the bubble/slurry reactors

Bubble/Slurry bubble column reactors(BCR/SBCR) are intensively used as multiphase reactors for a wide range of application in the chemical, biochemical and petrochemical industries. Most of these applications involve complicate gas–liquid/gas–liquid–solid flow behavior and exothermic process, thus it is necessary to equip the BCR/SBCR with heat exchanger tubes to remove the heat and govern the performance of the reactor. Amounts of experimental and numerical studies have been carried out to describe the phenomena taking place in BCR/SBCRs with heat exchanger tubes. Unfortunately, little effort has been put on reviewing the experiments and simulations for examining the effect of internals on the performance and hydrodynamics of BCR/SBCR. The objective of this work is to give a state-of-the-art review of the literature on the effects of heat exchanger tubes with different types and configurations on flow behavior and heat/mass transfer, then provide adequate information and scientific basis for the design and the development of heat exchanger tubes in BCR/SBCR, ultimately provide reasonable suggestions for better comprehend the performance of different heat exchanger tubes on hydrodynamics.     

碱性阻挡层抛光液中ULK介质抛光性能的研究

研究了化学机械抛光(CMP)过程中抛光液的SiO₂磨料质量分数和表面活性剂对多孔SiOCH薄膜(ULK介质)介电常数(k)及抛光速率的影响。所用抛光液(pH=10)主要由0%~4%(质量分数,下同)SiO₂、0.075%H₂O₂、1%邻苯二甲酸氢钾和不同质量浓度的表面活性剂组成,其中表面活性剂为非离子表面活性剂脂肪醇聚氧乙烯醚(AEO-9和AEO-15)、阴离子表面活性剂十二烷基硫酸铵(ADS)和两亲性非离子表面活性剂辛基苯酚聚氧乙烯醚(OP-50)。结果表明,磨料质量分数的增大会使ULK介质的去除速率和k值都增大。聚醚类表面活性剂都能在CMP过程中很好地保护ULK介质表面,降低其去除速率,OP-50的效果尤其好。当采用2%SiO₂+0.075%H₂O₂+1%KHP+200 mg/L OP-50的抛光液进行CMP时,ULK介质的去除速率为5.2 nm/min,k值增幅低于2%,Cu和Co的去除速率基本不变。     

高效全自动清淤系统在酸性水库的应用

针对 pH ≤ 3 的酸性水库周边地形复杂无法进入大型机械设备、淤泥沉积深夹带有大量织物、库底覆有土工膜易破损等特点,将前置浮船可升降的水面泥浆输送系统与地面泥浆输送系统串联可实现高浓度远距离管道输送,通过全自动监测,采用智能变频控制,保证系统在泥浆浓度可变、液面高度可变的大范围区间内连续且稳定运行。系统在调试运行期间,抽送高浓度泥浆为 19220.88m3,极大提高了酸性水库的清淤效率,降低了清淤成本。     

铜尾矿库尾矿全粒径规模化低碳消纳研究*

某大型矿冶集团针对该集团铜尾矿库尾矿大量堆存,安全环境风险突出,新建尾矿库选址困难、尾矿消纳途径有限等问题,通过长期摸索研究和对铜尾矿库尾矿粒径分布、成分、化学属性、浸出毒性和放射性等因素进行分析,探索出通过胶凝改造技术充填、制备公路工程无机结合料和铜尾矿资源脱硫分级综合利用的低碳材料消纳模式,尾矿库尾砂能够全粒径规模化消纳利用。单位产品分别消纳尾矿0.075t/t、0.1275 t/t和1t/t,降碳1.564t/t、0.054t/t和0.5195t/t,并分别具有40.0971元/t、12.1235元/t和14.4653元/t的环境正效益,同时协同处置了大量其他固体废物,真正实现了铜尾矿全粒径规模化增值消纳,在全国范围内有很好的借鉴意义。     

低成本钢尾渣-矿渣基矿山充填料的优化开发

 为实现多固废协同利用、降低充填成本,在矿渣基全粒级细尾砂胶结充填料基础上,以流动性和抗压强度为表征,利用热闷钢渣磁选尾渣(钢尾渣)替代部分矿渣作为胶凝材料,脱硫灰和水泥熟料替代部分专用添加剂作为外加剂,采用正交试验探寻掺量规律,优化固体填充料配比,开发钢尾渣-矿渣基软性矿山充填料,并研究了外加剂与胶材比、灰砂比等因素的影响。对比分析了矿渣基准组、钢尾渣-矿渣基准组(B1)、强度最优外加剂组分钢尾渣-矿渣组(B7)等3组充填料的微观形貌及XRD图谱以探究其水化机理。结果表明,钢尾渣替代矿渣量增加、外加剂与胶材比减小,充填料浆流动性改善,但充填体抗压强度下降。强度正交试验结果表明,钢尾渣掺量大小决定强度低高,脱硫灰掺量宜高于水泥熟料。进一步调整外加剂组分配比,在灰砂比为1∶6、钢尾渣替代矿渣为20%条件下,找出B7组外加剂组分为脱硫灰、水泥熟料分别替代30%、20%专用添加剂,B7组料浆扩展度为143 mm,充填体形貌为富铁绿泥石胶结假方体钙硅灰石,28 d抗压强度达2.13 MPa,较基准组低0.19 MPa,较B1提高0.26 MPa。该替代方案满足现场充填C2级强度的要求,改善流动性并显著降低了充填成本。优化的外加剂组分配比在灰砂比为1∶4条件下同样具有强度优化作用,但较灰砂比为1∶6条件下低。     

重金属强化含金矿石的氰化浸出

通过分析铊、铋、汞和铅等重金属强化金氰化溶解的电化学原理,对含金氧化物矿石和难浸硫化物金精矿进行了重金属强化浸金研究.结果表明:重金属对金氰化溶解的阳极过程有显著的强化作用,但在常规供氧条件下,金的溶解速率并未显著提高;只有同时采用阴极强化措施,才能使重金属起到显著提高金溶解速率的作用;对于含金氧化物矿石,单独采用重金属强化即可明显提高浸金速率,如果在过氧化氢助浸的基础上添加重金属,金的浸出速率会有更大幅度的提高;对硫化物金精矿而言,单独采用重金属无明显强化效果,只有在添加过氧化氢作为辅助氧化剂的基础上,重金属对金的浸出才能起到强化的作用,该体系中过氧化氢起到了强化阴极过程和氧化硫化物的双重作用.     

Technological condition in slurry electrolysis of high-silver galena concentrate

Effects of various technological conditions such as ρ(C1^- ), ρ(Fe)T, pH value and temperature on the cell voltage, lead leaching rate and the cathodic current efficiency of the slurry electrolysis of high-silver galena concentrate were studied, and the behavior regularity of lead and silver was investigated. As a result, the suitable condition was determinedas, ρ(C1^-)230g/L, ρ(Fe)T15g/L, pH 1, temperature 70℃, electrolysis time 6h. Under such condition,adopting the cathodic current density of 150 A/m2 and the liquid-solid ratio of 15 : 1, lead powder with a purity degree of 91. 18% was got. At the same time, leaching rate of lead, leaching rate of silver and cathodic current efficiency amounted to 96.88%, 70.88% and 75.68% respectively.     

Application of a time-dependent constitutive model to rheocast systems

A mathematical model has been developed to describe the velocity field in an agitated Al- 5Cu alloy in which B4C particles were suspended at different loading rates of up to 40 %. The material system was agitated by means of an electromagnetic rotary stirrer. The non- Newtonian behavior of the melt/solid slurry was allowed for using two models: the steady- state model of Joly and Flemings and the model of Brown, which takes account of time- dependent behavior. Calculations have shown that the two models behave similarly at high shear rates. In addition, if agitation was discontinued, very little time was required for the velocity (and hence the fluidity) of the slurry to decay.