外转子电机关键技术及解决措施

对外转子电机的关键技术和主要工艺问题进行了探讨分析，并提出了解决措施。     

沙角C电厂2号发电机转子接地检测装置改造

介绍沙角发电C厂2号发电机转子接地检测装置的基本原理和在装置发出报警信号后的分析和判断过程。对该装置出现故障后ALSTOM公司提出的临时检测方案作了分析，指出了该方案的不足之处，提出并实施改进后的临时检测方案。     

一种工艺过程流体强化装置

介绍了一种提高工艺过程效率的强化装置,即通过在过程设备上设置振荡装置,使过程设备内的流体产生扰动,破坏流动边界层,使流体获得附加雷诺数提高流动的湍流程度,达到强化过程设备内工艺过程的目的。该强化装置的调节弹性大,适应范围宽。调节强化装置中转子的转速、几何尺寸、空间位置和方向等参数或更换挡板形式,就能适应各种工艺过程条件。该装置可用于传热、传质及化学反应等多种过程,以提高过程效率,节约能源和资金,减小设备体积,并可将机械搅拌类的间歇过程转化为连续过程。     

电动机笼形转子铸铝常见质量问题分析

在电机制造中，笼形转子三相异步电动机的转子铸铝质量的好坏直接影响电机的性能及力能指标。因此本文对常见的转子铸铝质量问题进行了分析，并提出了相应地解决措施，以获得优质的电机。     

黄埔发电厂#6发电机转冷水系统改造

黄埔发电厂#6发电机转冷水铜离子含量超标，通过对缺陷原因进行分析，针对二级水封的特性对溢出的转冷水进行回收并利用化学凝结水处理去除溶出的铜离子，通过控制转冷水的pH值最终减缓铜管的腐蚀.     

FINITE ELEMENT ANALYSIS OF THE FLOW INDUCED BY ROTATING BLADES IN AN INCOMPRESSIBLE VISCOUS FLUID

Aerodynamic loads on a multi-bladed helicopter rotor in hovering flight were calculated by solving the three-dimensional incompressible Navier-Stokes equations. The rotor wake effects were accounted by the correction of local geometric angle of attack according to a free-wake modeling in addition to an empirical modification for the tip flow effect. The validity and efficiency of the present method were verified by the comparisons between numerical results and experimental data.     

转子系统热膨胀状态下固有横振频率

把转子的惯性力看成作用在轴上的外力,采用新的非线性渐近法研究热膨胀对转子系统固有横振频率的影响.     

Detection of multiple cracks using frequency measurements

A method for detection of multiple open cracks in a slender Euler-Bernoulli beams is presented based on frequency measurements. The method is based on the approach given by Hu and Liang [J. Franklin Inst. 330 (5) (1993) 841], transverse vibration modelling through transfer matrix method and representation of a crack by rotational spring. The beam is virtually divided into a number of segments, which can be decided by the analyst, and each of them is considered to be associated with a damage parameter. The procedure gives a linear relationship explicitly between the changes in natural frequencies of the beam and the damage parameters. These parameters are determined from the knowledge of changes in the natural frequencies. After obtaining them, each is treated in turn to exactly pinpoint the crack location in the segment and determine its size. The forward, or natural frequency determination, problems are examined in the passing. The method is approximate, but it can handle segmented beams, any boundary conditions, intermediate spring or rigid supports, etc. It eliminates the need for any symbolic computation which is envisaged by Hu and Liang [J. Franklin Inst. 330 (5) (1993) 841] to obtain mode shapes of the corresponding uncracked beams. The proposed method gives a clear insight into the whole analysis. Case studies (numerical) are presented to demonstrate the method effectiveness for two simultaneous cracks of size 10% and more of section depth. The differences between the actual and predicted crack locations and sizes are less than 10% and 15% respectively. The numbers of segments into which the beam is virtually divided limits the maximum number of cracks that can be handled. The difference in the forward problem is less than 5%.     

水轮发电机转子动平衡的时-频方法

提出了一种基于时域分析和频域分析的动平衡方法，应用于水轮发电机转子的动平衡。在这种时-频动平衡方法中，用时域分析来确定不平衡力的相位，用频域分析来确定不平衡力的大小。该方法具有平衡精度高、起机次数少的优点。用1台300MW水轮发电机转子的现场试验数据验证了该方法的准确性和适用性。     

LY-8602系列催化剂的失活原因及对策

通过催化剂的评价及表征，对LY-8602系列催化剂在低硫裂解汽油加氢时的失活原因进行了研究，结果表明，其活性下降主要是催化剂的活性中心相Co-Mo-s遭到破坏，使催化剂表面的具有加氢活性的Mo^4 峰减小所致。采用新研制的高活性加氢催化剂LY-9702与LY-8602构成复合床催化剂，可以使加氢产品合格。