Numerical simulations of specimen size and mismatch effects in ductile crack growth - Part II: Near-tip stress fields

The effect of ductile crack growth on the near tip stress field in two different specimen geometries has been investigated. For homogeneous specimens it is observed that the peak stress level increases with ductile crack growth. The effect is most pronounced up to about 1 mm of crack growth. For low and intermediate hardening there is a significant effect of specimen size on the stress level. In case of mismatch in yield stress, the simulations show that the increase in stress level in the material with the lower yield stress is of a similar magnitude as is the case for stationary cracks. In case of ductile crack growth deviation from the original crack plane occurs, the highest stresses are still found close to the interface, and not in front of the current crack tip.     

聚合物-金属界面相形貌的研究

环氧树脂在 Al 合金表面生成纤维状的界面相结构,其形成、发展和特征与树脂的体系、交联反应条件以及 Al 合金的表面状态有关。环氧树脂的基础相为颗粒状的超结构组织。聚合物界面相的力学破坏表现为纤维体的拉伸、变形和断裂,而基础相在纯剪切受力时出现在45°方向的裂纹,并发展导致连接层的破坏。     

A One-Dimensional Nonlocal Damage-Plasticity Model for Ductile Materials

This paper presents a new 1-D non-local damage-plasticity deformation model for ductile materials. It uses the thermodynamic framework described in Houlsby and Puzrin (2000) and holds, nevertheless, some similarities with Lemaitre’s (1971) approach. A 1D finite element (FE) model of a bar fixed at one end and loaded in tension at the other end is introduced. This simple model demonstrates how the approach can be implemented within the finite element framework, and that it is capable of capturing both the pre-peak hardening and post-peak softening (generally responsible for models instability) due to damage-induced stiffness and strength reduction characteristic of ductile materials. It is also shown that the approach has further advantages of achieving some degree of mesh independence, and of being able to capture deformation size effects. Finally, it is illustrated how the model permits the calculation of essential work of rupture (EWR), i.e. the specific energy per unit cross-sectional area that is needed to cause tensile failure of a specimen.     

A probabilistic model for cleavage fracture with a length scale--parameter estimation and predictions of stationary crack experiments

This study presents a large experimental investigation in the transition temperature region on a modified A508 steel. Tests were carried out on single-edge-notch-bend specimens with three different crack depth over specimen width ratios to capture the strong constraint effect on fracture toughness. Three test temperatures were considered, covering a range of 85 °C. All specimens failed by cleavage fracture prior to ductile tearing. A recently proposed probabilistic model for the cumulative failure by cleavage was applied to the comprehensive sets of experimental data. This modified weakest link model incorporates a length scale, which together with a threshold stress reduce the scatter in predicted toughness distributions as well as introduces a fracture toughness threshold value. Model parameters were estimated by a robust procedure, which is crucial in applications of probabilistic models to real structures. The conformity between predicted and experimental toughness distributions, respectively, were notable at all the test temperatures.     

Dynamic crack propagation with cohesive elements: a methodology to address mesh dependency

In this paper, two brittle fracture problems are numerically simulated: the failure of a ceramic ring under centrifugal loading and crack branching in a PMMA strip. A three‐dimensional finite element package in which cohesive elements are dynamically inserted has been developed. The cohesive elements' strength is chosen to follow a modified weakest link Weibull distribution. The probability of introducing a weak cohesive element is set to increase with the cohesive element size. This reflects the physically based effect according to which larger elements are more likely to contain defects. The calculations illustrate how the area dependence of the Weibull model can be used to effectively address mesh dependency. On the other hand, regular Weibull distributions have failed to reduce mesh dependency for the examples shown in this paper. The ceramic ring calculations revealed that two distinct phenomena appear depending on the magnitude of the Weibull modulus. For low Weibull modulus, the fragmentation of the ring is dominated by heterogeneities. Whereas many cracks were generated, few of them could propagate to the outer surface. Monte Carlo simulations revealed that for highly heterogeneous rings, the number of small fragments was large and that few large fragments were generated. For high Weibull modulus, signifying that the ring is close to being homogeneous, the fragmentation process was very different. Monte Carlo simulations highlighted that a larger number of large fragments are generated due to crack branching. Copyright © 2003 John Wiley & Sons, Ltd.     

Preparation of Plate Fe_(60)Co_8Zr_(10)Mo_5W_2B_(15) Bulk Amorphous Alloy and Its Fracture Toughness

1Introduction Duwez[1]synthesizedthefoilAu Siamorphousalloyforthefirsttimewithrapidsolidification,whichinitiatedthepreparationofamorphousalloysintheprocessofalloysolidification,andthereaftertheresearchonamorphousal loysdevelopedrapidly.Since1980s,withthec…     

粗轧机前推床同步拉杆断裂的分析与改进

通过对机前推床同步拉杆的受力分析及强度计算，查找出了造成拉杆断裂的原因，并提出了解决拉杆断裂的具体措施。     

高压水射流射孔井眼应力数值模拟研究

水力射孔技术是一种新型完井方式,利用深穿透水力射孔技术辅助定向压裂,可实现油层改造和油井增产。考虑套管水泥环的影响,采用有限元理论结合ANSYS软件计算了高压水射流水力射孔井眼周围的应力,重点分析了水力射孔参数对井周应力的影响规律,初步研究了直井水力压裂时水力射孔对裂缝起裂的影响。计算结果表明,沿最大水平地应力方向布孔时,孔眼根部的周向拉应力最大,裂缝将会在孔眼根部起裂;选择合理水力射孔参数可有效降低地层破裂压力。研究结果可为高压水射流水力射孔辅助定向压裂提供参数优选的依据。     

水力压裂净压力拟合分析解释技术研究与应用

基于三维裂缝延伸模拟模型的水力压裂净压力拟合分析解释技术,提出了净压力拟合分析解释的一般步骤及理论方法,研究了现场监测净压力的计算方法,并介绍了其在现场施工中的应用情况。该技术可以帮助认识地层参数和压裂参数,提高压裂施工成功率和有效率。     

Moral value transfer from regulatory fit: What feels right is right and what feels wrong is wrong.

People experience regulatory fit (E. T. Higgins, 2000) when the strategic manner of their goal pursuit suits their regulatory orientation, and this regulatory fit feels right. Fit violation feels wrong. Four studies tested the proposal that experiences of fit can transfer to moral evaluations. The authors examined transfer of feeling wrong from fit violation by having participants in a promotion or prevention focus recall transgressions of commission or omission (Studies 1 and 2). Both studies found that when the type of transgression was a fit violation, participants expressed more guilt. Studies 3 and 4 examined transfer of feeling right from regulatory fit. Participants evaluated conflict resolutions (Study 3) and public policies (Study 4) as more right when the means pursued had fit. (PsycINFO Database Record (c) 2010 APA, all rights reserved)