Hydrogenation of CO2 to Hydrocarbons over Zirconia-Supported Cobalt Catalyst Promoted with Potassium

Catalysis Letters - The purpose of this study was to investigate the promotive effect of potassium on the catalytic performance and properties of Co/ZrO2 catalysts during hydrogenation of CO2 to...     

Three and one-dimensional hierarchical α-Fe2O3 nanostructures for photoelectrochemical water oxidation

Journal of Materials Science: Materials in Electronics - Herein, we report the synthesis of three-dimensional (3D) and one-dimensional (1D) hierarchical hematite (α-Fe2O3) nanostructures on...     

Modifying the photocatalytic property of ZnO-based photoelectrodes by introducing MgFe2O4 nanoparticles

Journal of Materials Science: Materials in Electronics - Limited light absorption and acute charge recombination on the surface of ZnO nanostructure-based photoelectrodes are the basic challenges...     

Impression creep behavior of different zones in friction stir welded Mg–Zn–Mn wrought alloy

The friction stir welded joint of wrought ZM21 alloy was divided into five parts, and their localized creep behavior was studied via the impression method. The tests were carried out in the stress range of 300–450 MPa (σ_imp/G ≈ 0.02–0.03) and in the temperature range of 448–523 K. Optical and SEM micrographs and EDS taken before and after the impression tests were used to study the microstructure of various zones of the FS welded joint. Power law was found to satisfactorily relate the stress and strain rates. The steady-state impression velocity was found to vary significantly between the advancing and retreating sides of TMAZ and HAZ. For TMAZ, the creep exponent on the AS was 4.8, and on the RS, it was 7.8. The activation energy on the AS was ~?133 kJ/mol, and on the RS, it was ~?101 kJ/mol. Similarly, for HAZ, the creep exponent on the AS was found to be 5.5 and on the RS, it was 4.9. The activation energy on the AS was ~?86 kJ/mol and on the RS, it was ~?232 kJ/mol. The cross-over of steady-state impression velocity of different zones indicates that the weak zone was temperature and stress dependent. Within the stresses and temperatures studied, the weld zone's creep resistance (i.e., lower minimum impression velocity) was found to be better than the base material. As it is with most magnesium alloys, dislocation climb was found to be the operative mechanism in the FS weldments of ZM21 alloy. The rate-controlling mechanism remains to be identified because the wide variation in n and Q values suggests that different creep mechanisms are in operation in different zones.

Graphical abstract

     

Analysis of energy saving in user equipment in LTE-A using stochastic modelling

Telecommunication Systems - Energy saving in User Equipment (UE) is one of the important issues for limited sources of power in the device. It is critical for the UE to maximize its energy...     

Optimizing the Structure of a Production System for Activated Carbon

Russian Engineering Research - A system for the production of activated carbon is considered. The thermal deformation of its components in operation is of interest. A frame design is developed,...     

As the number falls,alternatives to the Hagberg–Perten falling number method: A review

This review examines the application, limitations, and potential alternatives to the Hagberg–Perten falling number (FN) method used in the global wheat industry for detecting the risk of poor end-product quality mainly due to starch degradation by the enzyme α-amylase. By viscometry, the FN test indirectly detects the presence of α-amylase, the primary enzyme that digests starch. Elevated α-amylase results in low FN and damages wheat product quality resulting in cakes that fall, and sticky bread and noodles. Low FN can occur from preharvest sprouting (PHS) and late maturity α-amylase (LMA). Moist or rainy conditions before harvest cause PHS on the mother plant. Continuously cool or fluctuating temperatures during the grain filling stage cause LMA. Due to the expression of additional hydrolytic enzymes, PHS has a stronger negative impact than LMA. Wheat grain with low FN/high α-amylase results in serious losses for farmers, traders, millers, and bakers worldwide. Although blending of low FN grain with sound wheat may be used as a means of moving affected grain through the marketplace, care must be taken to avoid grain lots from falling below contract-specified FN. A large amount of sound wheat can be ruined if mixed with a small amount of sprouted wheat. The FN method is widely employed to detect α-amylase after harvest. However, it has several limitations, including sampling variability, high cost, labor intensiveness, the destructive nature of the test, and an inability to differentiate between LMA and PHS. Faster, cheaper, and more accurate alternatives could improve breeding for resistance to PHS and LMA and could preserve the value of wheat grain by avoiding inadvertent mixing of high- and low-FN grain by enabling testing at more stages of the value stream including at harvest, delivery, transport, storage, and milling. Alternatives to the FN method explored here include the Rapid Visco Analyzer, enzyme assays, immunoassays, near-infrared spectroscopy, and hyperspectral imaging.     

Controlling the Heating of a Rod Using the Current and Preceding Time Feedback

Automation and Remote Control - Using the process of heating a rod in a furnace as an example, we study the feedback control synthesis problem for plants with distributed parameters. To form the...